Enwork Landing User manual

Landing
Rev A 7/30/18
Landing Team Table (Solid Surface/Quartz) Installation Instruction
Installation Instructions

1) Parts and Fasteners Included
INSTALLATION GUIDE
24mm Cam Dowel 8mm x 1in Dowel Pins
Keel Block Keel
Sub Top Top SurfaceEnd Panel
#10 x 2 Phillips Screw
#10 x 1 Phillips Screw

1) Parts and Fasteners Included
INSTALLATION GUIDE
Angle BracketWire Chase (Left & Right) Wire Chase Door Panel

1) Parts and Fasteners Included
INSTALLATION GUIDE
5/16 Flange Nut #10 x 1 Phillips Screw
Foot Bar Weldment
Angle Bracket
Optional Foot Bar Parts

2) Tools and Supplies Required
INSTALLATION GUIDE
Phillips Drive Phillips Head Screw Driver Rubber Mallet
Cordless Drill Ratchet 5/16 Deep Socket

4) Assembly:
INSTALLATION GUIDE
Fig. 2
Fig. 3
Fig. 2 Assemble Keel Block and Keels. Keel Blocks
should be assembled with the Cam Dowel surfaces
facing each other(as shown).
Fig.3 Assembly should be placed as shown (Edge
band side up)
Keel Sub Assembly
Fig. 1
Fig. 1 Install (4) Cam Dowels Pins into the (4) centrally
located 5mm pre drilled holes on the Keel. Repeat for
second Keel.

4) Assembly:
INSTALLATION GUIDE
Fig. 5
Fig. 5 Align the Cam Dowels and Dowel Pins and
assemble the (2) End Panels and the Keel Sub
Assembly.
Assemble with End Panel Glides up (as shown).
Base Sub Assembly
Fig. 4
Fig. 4 Install (4) Cam Dowels Pins & (6) 8mm Dowels
Pins into (10) centrally located pre drilled holes on the
End Panel. Repeat for second End Panel.
Fig. 6
Fig. 6 Ensure all Cam Dowels are tight and flip the
entire Base Sub Assembly into an upright position (End
Panel Glides down). Be careful not to damage End
Panel edges and corners.

4) Assembly:
INSTALLATION GUIDE
Fig. 7 Insert the 8mm Cam Dowels Pins into the 5mm
pre-drilled holes on the Sub Top (bottom surface
shown).
Top Assembly
Fig. 9 Secure Sub Top to End Panels with #10 x 2
Phillips Screws using pre-drilled holes.
Insert (4)8mm x 1 Dowel Pins into the End panels.
Fig. 7
Fig. 9
Fig.8
Fig 8. Align the Cam Dowels Pins and Cams and
assemble the Sub Top to the Base Sub Assembly. Cam
the Sub Top and the Base Sub Assembly together.

4) Assembly:
INSTALLATION GUIDE
Fig. 11 Insert Cam Dowels Pins into the 5mm pre-
drilled holes on the End Panels. Align the Cam Dowel
Pins and Cams and assemble the Wire Chase Side
Panels.
Top Assembly
Fig. 12 Cam the Sub Top and the Base Sub Assembly
together
Fig. 11
Fig. 12
Fig. 10
Fig. 10 Align the Top Surface with the 8mm Dowel
Pins and install the Top Surface.

4) Assembly:
INSTALLATION GUIDE
Top Assembly
Fig. 14 Install Wire Chase Door Panels
Fig.14
Fig. 13
Fig. 13 Install the Angel Brackets to the End Panels
and Wire Chases using the 1/8in pre drilled holes.
Secure using #10 x 1 Phillips Screw
Fig. 15 Level the Landing Table using the End Panel
Levelers.
Fig.15

4) Assembly:
INSTALLATION GUIDE
Fig. 16
Fig. 17
Fig. 16 Attach Angle Bracket to End Panel with (4) #10 x
1 Phillips Screws using 1/8in predrilled holes. Repeat
for opposite End Panel.
Fig. 17 Attach foot Bar Weldment using (2) 5/16 Flange
Nuts. Repeat for opposite End Panel
Optional Foot Bar Assembly

12900 Christopher Drive Lowell, MI 49331
800.815.7251 www.enwork.com
Specifications subject to change without notice.