Enwork Odyssey User manual

Odyssey
Installation Guide
PART NUMBER SABXXX
CONFERENCE TABLES
TI0082
Odyssey Conference Table Installation Guide – Rev 02.23

2TI0082 - Odyssey Table Installation Instructions
1 — TOOLS AND SUPPLIES REQUIRED
Drill Hex Head Driver
Level
Dead Blow Hammer
Marker
Philips Screw Driver
Ratchet
Square Head Driver
Combination Wrench
Socket
Philips Head Driver
Tape Measure
Utility Knife

3TI0082 - Odyssey Table Installation Instructions
2 — INCLUDED PARTS AND FASTENERS
10-10 x 1“ Truss Head SQ/
Phillips (SCREW 1)
#10 x 1/2“ Phillips Flat Head
Wood Screw

Serrated Flange Bolt

Zipbolt Surface Connector Clear Rubber Bumper,
Adhesive Backed

Bolt

Bolt
¼-20 x 1-¼
Socket head Cap Screw


Phillips Pan Head

Flathead Screw
Washer

Hex Head Bolt
Binding Bolt
Wood Dowel

4TI0082 - Odyssey Table Installation Instructions
2 — INCLUDED PARTS AND FASTENERS

Bolt

Bolt
Level

Philips
Embedded Brace

Top Connection Bracket

Base Bottom Assembly

Top Plate Assembly
(SAM-2003-x)


Philips



Draw Plate 1
(EAM-1000-1)

Bolt
Base Leg

Draw Plate 2
(EAM-2000)

5TI0082 - Odyssey Table Installation Instructions
2 — INCLUDED PARTS AND FASTENERS
Base Shroud

Right Extrusion (EAA-2002-x-R)
OR (EAA-2003-x-R)
C-Channel
(EAM-1001-xx)
Left Extrusion (EAA-2002-x-L)
OR (EAA-2003-x-L)
Mid Extrusion
(EAA-2002-x-M)

6TI0082 - Odyssey Table Installation Instructions



connection holes on the Base Bottom Assembly.


connection holes on the Base Bottom Assembly.

3.1
3.3
3.2
3 — BASE ASSEMBLY
2x
2x
2x

Base Leg assembly, until it covers the Assembly.
3.4
2x

7TI0082 - Odyssey Table Installation Instructions
Line up the connection holes of the Top Plate
Assembly(SAM-2003-x) with the Base Leg assembly.

When the base assemblies are completed,

Note: If there are the access doors present
they should face to the inside.
Connect the Top plate assembly to the Right
Angle Bracket (pre installed on Base Shroud) on

3.5
3.7
3.6
3 — BASE ASSEMBLY
2x 2x

8TI0082 - Odyssey Table Installation Instructions
Extrusion Description
Top
Bottom
Outside
Inside
U-Channel
Space
Assemble the C Channels (EAM-1001-xx) into the

facing up and the opening of the C facing outside.
Note: Do not tighten the bolts at this time
Place the extrusions in a clear area on a non marring
surface, in an order similar to their completed position.
Note: The Number of extrusions is dependent on table length.
Assemblies with 2 extrusions, assemble
the Left and Right Extrusion
Assemblies with 3 extrusions, skip to
section 5) Table Frame Assembly
Assemblies with 4 extrusions, assembly the Mid Extrusion
4.1
4.3
4.2
4 — EXTRUSION ASSEMBLY


Note: Do not tighten the bolts at this time
4.4

9TI0082 - Odyssey Table Installation Instructions
Slide the next extrusion on to the C-Channel.
Assemble (1) Draw Plate 1, (1) Draw Plate 2

connection hole and loosely tighten so the

Note: The extrusions must be aligned and square before they
are fully tightening. Adjust as necessary while tightening.
Once the Draw Plates are fully tightened, Fully tighten



Note: Depending on table length, Left & Right
Extrusions may be assembled at this point.
4.5 4.6
4 — EXTRUSION ASSEMBLY

10TI0082 - Odyssey Table Installation Instructions
Place the fully assembled beams on the
Base Assembly, seating the channel of the
extrusion in to the U Channel of the base.
Secure the ends of both extrusion to the

bolt, then proceed to secure the extrusion

Repeat process for the other end of the table.
Align the holes of the assembled beams to
the holes of the assembled bases.
5.1
5.3
5.2
5 — TABLE FRAME ASSEMBLY
Slide the extrusions completely until the
surfaces meet. The C Channel holes
should align with the top slots on the
middle extrusion assembly, shown right.
5.4

11TI0082 - Odyssey Table Installation Instructions
Slide the extrusions completely until the surfaces
meet. The C Channel holes should align with the top
slots on the middle extrusion assembly, shown right.
Loosely assemble the Top Connection Bracket, (2)

Insert the this assembly into the inside of the extrusions
There will be 2 for every Top Connection


bolt into each Extrusion connection hole and tighten.
Note: The extrusions must be aligned and square before they
are fully tightening. Adjust as necessary while tightening.
Fully tighten the bolts connecting the extrusion
to the base at this time (see Fig 5.5).
5.5
5.7
5.6
5 — TABLE FRAME ASSEMBLY
Position the 2 outer most Top Connection

and then evenly distribute the remaining
Brackets along the length of the extrusion.
Do not tighten yet. These may need to be
repositioned later in the assembly process.
5.8

12TI0082 - Odyssey Table Installation Instructions
Loosely assemble the Extrusion Cap (EAM-2010-x) ,

Press the end cap in all the way tight against the
end of the extrusion. Insure the back side of the

Fully tighten
5.9
5 — TABLE FRAME ASSEMBLY
2x

13TI0082 - Odyssey Table Installation Instructions
Levelers are accessible through the
access hole on the tops of the base.
Place a level spanning both beams and
level the table across it’s depth.
Place a level on the beam between the 2

6.1
6.3
6.2
6 — LEVELING

14TI0082 - Odyssey Table Installation Instructions
Place the worksurfaces on a non-marring surface and
attach the Embedded Braces to the routings using
the #10 x 1.00 Pan Head Phillips Wood Screws.
Note: When attaching the braces, secure both end and
then use every other screw hole provided. This will aid
when attaching the work surface to the table frame.
Before attaching the work surface to the table tops
assembly, verify there is no interference with the Top
Connection Bracket and any power unit/cutouts.
Location of the Top Connection Bracket

Tighten all of the brackets to the extrusion at this time.
Place the work surfaces onto the table frame. When
placing the end piece, insure there are no screw heads
interfering between the worksurface and the beams.
Any screw(s) causing interference may be removed.
This will only occur on the End Work Surface pieces.


Note: number of surfaces may vary depending on table length.
7.1
7.3
7.2
7 — TABLE TOP ASSEMBLY
Verify the work surface is aligned and centered.
Attach the work surface to the table assembly using

7.4

1.800.815.7251
enwork.com
12900 Christopher Dr. Lowell, MI 49331
Specications subject to change without notice.
Rev 02.2023