EOS SBM App Module Manual instruction

EOS SBM App module and EOS Spa Control app – quick start up guide Print no. 2934 4672 13.21
EOS SBM App Module
General guide for setup and operation
Before the setup
Install the SBM App module and connect it to the sauna control unit with the pre-mounted sauna bus
cable (requires a free RJ12 sauna bus connector in the sauna control unit). Connect the module to
your router / cable modem (internet access point) using a standard Ethernet cable (RJ45). Make sure
the internet connection is available and is not blocked by the firewall (port 7250 should be available).
Make sure the sauna control unit has been set up correctly and remote control has been cleared
during initial setup.
01 Setup preparation
Download the free “EOS Spa Control” app on your mobile device from the Google PlayStore or Apple
AppStore and install it. Keep the sauna control unit and the SBM App module powered (stand by
mode). Launch the app. Self-guided setup process will lead you through all steps.
02 Welcome screen
Welcome to the setup of your EOS Spa Control app. Tap on “launch setup”
button to start.
03 MAC address
For setup and pairing you will need an individual MAC address. This
address you can find printed on the type shield attached on the SBM App
module.

EOS SBM App module and EOS Spa Control app – quick start up guide Print no. 2934 4672 13.21
03 Enter the MAC address
Pairing step 1
Give in the last three pairs of the individual MAC address in the
corresponding fields.
„Where do I find the MAC address“ – press to get help with locating the
MAC address.
Tap on “Start pairing” to initiate the pairing sequence. Hold on a pointed
tool, e.g. a paper clip, ready.
04 Press the pairing button
Pairing step 2
Now press firmly on the pairing button on the SBM App module with a
pointed tool (e.g. paper clip end) for 1 second.
You need to do this within 60 seconds. The countdown will be displayed
on the app screen.
05 Pairing successful
Pairing step 3
If the pairing has been successful, the appropriate confirmation screen
will be displayed. Otherwise repeat the pairing.
You mobile device is now successfully paired with the app module (with
your sauna control unit).
Tap on “Next” to finalize the setup.

EOS SBM App module and EOS Spa Control app – quick start up guide Print no. 2934 4672 13.21
06 Name your sauna
Pairing step 4
Here you can assign a name to your sauna, for instance “My Sauna”.
To complete the setup tap on the “to the control” button.
How to control your sauna with the app
01 Start you sauna
To unlock the app and start your sauna (start heating) press and hold
both buttons for 3 seconds.
02 Faulty connection
If the app has lost connection to the SBM App module, e.g. no internet
connection or due to a connection fault, an error message will be shown:
“No connection to the sauna can be established at the moment. Please try
again later”.
The app will try to reconnect automatically. The error message will
disappear once the connection has been re-established.

EOS SBM App module and EOS Spa Control app – quick start up guide Print no. 2934 4672 13.21
03 Sauna being started
While the start or stop command is being transmitted to the sauna control
unit a temporary overlay screen „your sauna is being switched on“ will be
displayed.
04 Climate settings
If you have a dry Finnish sauna or a sauna with
humidity operation the climate settings interface
will accordingly display the settings for
temperature only (right image) or temperature
and humidity (left image). Use +/- to adjust.
You can also switch light and stop the heating
through the corresponding buttons.
Current climate values will be displayed in the
upper area.
05 Other settings
Press the cog symbol the upper right corner to check the global
parameters, such as the sauna cabin name, paired MAC address and the
app version.
In this submenu you can delete the pairing – for this press on “disconnect
sauna”.