Eterna D040 Setup guide

Ifyou experience problems:
If your lightisdefectiveor developsafault, pleasereturn ittothe placewhere you boughtit. You can call
our Helpline for advice.TheHelpline will gladlygiveadviceon anyaspectofanyEterna Lighting product
but may notbe able togivespecific instructions regarding individual installations.
Ifindoubt,consultaqualified electrician.
Helpline:
Tel:[phone]Fax: [phone]Email: [e-mail]
For answers tofrequently asked questions (FAQs)and other information visit our web-site
www.eterna-lighting.co.uk
Lampreplacement:
>Switchoff the electricityatthe mains.
>Removethe glassdiffuser byprizing the metal ring that retainsit outofthe fitting using asmall flat
bladed screwdriver.
>Pull the old lampstraight out of its socket and replaceonlywithone ofthe sametypeand rating.
IMPORTANT !Do nottouch thelamp withbarefingers,use asoft clean clothor tissue.
>Replacethe glass diffuser pressing firmly backintoplace.
Replacementlamptype:
Wattage: 20 W
Supply Voltage:12 V
Type:G4 M47 capsule
Cleaning:
>Clean this lightfitting onlywithasoftdry cloth
>Donot useanychemical or abrasivecleaners.
Eventually, you may wanttoreplace thislightfitting:
When your lightfitting comestothe end ofit’slifeor you choosetoupdateor upgrade it
byreplacing it,pleasedonotdisposeofitwithyour normalhousehold waste,please
recycle where facilitiesexist. When you need todisposeofthisfitting,check withyour
retailer or local authority for suitable options. Newregulationswill encouragethe
recycling ofWastefromElectricaland ElectronicEquipment(European “WEEE
Directive”effectiveAugust 2005 ).
PLEASE READ THESE INSTRUCTIONSBEFORE
INSTALLING YOUR NEWFITTING
--
PLEASE RETAINFORFUTUREREFERENCE
Surface /recessmountedcapsule
downlights
Model(s)
D040,D041, D042,D043, D044,D045
Pack contents:
Capsule downlight 1
Surfacemounting ring 1
G4 M47 20W capsule lamp 1
Fixing pack 1

Safetymarkings:
Read thisfirst:
>Ifin anydoubt,consultaqualified
electrician.
>Suitable for indoor useonly.
>Thisproduct isonlysuitable for usein living
areas(notfor areasconstantlysubject to
moisture ).
>Thisproduct issuitable for installation on
surfaces withnormal flammability(indicated by
the "F" in atriangle )e.g.wood,plasterboard,
masonry. It isnotsuitable foruseonhighly
flammable surfaces(e.g.polystyrene,
textiles ).
>Useonlywithasuitable 240V /12Vstepdown
transformer.
>Donot connect lights directly tothe mains.
>Donotoverload the transformer,check that the
total Wattage ofall fittingsdoesnotexceed the
maximum marked on the transformer.
>Before making fixinghole(s),checkthatthere
are no obstructionshiddenbeneaththe
mounting surfacesuchaspipes or cables.
>Makesurethatthe fixingsare strong enough to
supportthe considerable weightofthe fitting
and hold it rigidly.
>If the location ofyour newfitting requiresthe
provision ofanewelectrical supply, the supply
must conformwiththe requirements ofthe
latest edition ofthe IEE wiring regulations.
>Donotcoverthe fitting and /or transformer
withany insulating materials.
>Thisfitting usesSELV (Safety Extra Low
Voltage ). Donotconnect any parttoearth.
>The fitting must be positioned sothat there is at
least 0.3m(300mm )between the bulb and
anyilluminated surface.Donotusethe fitting
without the safetyshield fitted.
>When replacing thelamp,do nottouchwith
bare fingers, grip the lampwithatissueor
clean soft cloth.
>Donotattachtosurfaceswhichare damp,
freshlypainted or otherwiseelectrically
conductive(e.g.metallic surfaces).
>Ifin anydoubt,consultaqualified
electrician.
Installation:
SURFACE
1) Check thatthetransformer you intend touseto
power your fitting isadequatelyrated for the
total number offittingsyou are installing and
thatithasbeen installedin accordancewithall
of the manufacturers instructions.
2) Choosethe location for your new fitting.
3) Prepare the routefor the cable between the
light and the transformer.
4) Extract the lightfromits surround bygently
levering itoutusing asmallscrewdriveror
other flatbladed implement. Takegreatcare
not todamage the decorativefinish.
5) Withthe cable threaded through the surround,
secure the surround in position usingsuitable
fixings appropriatetothe mounting surface.
6) Gently pull the cable through your prepared exit
routeand press the lightfitting backintothe
surround. Makesure thatyou do not trap aloop
of cable behind the light fitting.
7) Makethe connection ofthe cable tothe
transformer.Werecommend the useofan
Eterna Lighting transformer whichhassockets
designed toallowthe plug fittedtoyourlightto
plug directly in.
Note:Ifyou haveanyother transformer in
whichthere is no provision for connection using
the plug fitted toyour light,you willneed tocut
the plug off and usean alternativemethod of
connection.Theconnectionstothe lightfitting
are notdesignated Liveor Neutral.Make
connectionsusing aterminal block, ensure that
there are no strandsofwire protruding and
wrap well withinsulating tape.
8) Restore the power and switchon.
RECESSED
1) Check thatthetransformer you intend touseto
power your fitting isadequatelyrated for the
total number offittingsyou are installing and
thatithasbeen installedin accordancewithall
of the manufacturers instructions.
2) Choosethe location for your new fitting.
3) Prepare the routefor the cable between the
light and the transformer.
4) Extract the lightfromitssurround bygently
levering itoutusing asmall screwdriver or
other flatbladed implement.Takegreatcare
not todamage the decorativefinish.
5) Makeahole in the mounting surfaceof61mm
diameter.
6) Gently pull the cable through your prepared exit
routeand press the lightfitting backintothe
mounting surface.Makesure thatyou do not
trap aloop of cable behind the light fitting.
7) Makethe connection ofthe cable tothe
transformer.Werecommend theuseofan
Eterna Lighting transformer whichhassockets
designed toallowthe plug fitted toyour lightto
plug directly in.
Note:If you haveanyother transformer in
whichthere is no provision for connection using
the plug fitted toyour light,youwill need tocut
the plug off and usean alternativemethodof
connection.The connectionstothelightfitting
are notdesignated Liveor Neutral.Make
connectionsusing aterminal block, ensure that
there are no strandsofwireprotruding and
wrap well withinsulating tape.
8) Restore the power and switchon.
Important!
Never touchthe glass when the lightisswitched on.
Allow light tocool before changing the bulb
61mm
Prizeout glass and
ring withflatblade
Assembling the plug:
>Onceyou havethreaded the cablesfromyour light toyour transformer,
you will need topushthe pinsatthe endsofyour cablesintothe plug
body. Note,oncethe pins havebeen inserted they cannot be removed.
Hole cut outrequired: 61mm diameter.