Eterna RDL12 User manual

Model:
RDL12 / RDL18
Recessed LED Downlight
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
Pack contents:
1 x Fitting
1 x Driver
1 x 250mm cable
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
874/2012
MODELNO.
RDL Range
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.
CLEANING:
Clean this light tting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
RDL12
RDL18
Email: [email protected].uk / [email protected].uk
Visit our website: www.eterna-lighting.co.uk Made in ChinaIssue 0716
LAMP SPECIFICATIONS: RDL12 RDL18
Lumens total ux 1010 lm 1510 lm
Lumens from chip 1200 lm 1800 lm
Rated Wattage 12.7W 18.5W
Rated luminous ux 1010 lm 1510 lm
Nominal life time of the lamp 25,000 hrs 25,000 hrs
Colour temperature 4000K 4000K
Number of switching cycles
before premature lamp
failure
15,000 15,000
Warm-up time up to 60 % of
the full light output Instant full light Instant full light
Dimmable No No
LED array area (Ø) 145mm 205mm
Nominal beam angle >120° >120°
Rated power 12.7W 18.5W
Rated lamp lifetime 25,000 hrs 25,000 hrs
Lamp power factor >0.9 >0.9
Lumen maintenance factor at
end of nominal life 70% 70%
Starting time 0.1s 0.1s
Colour rendering >80 >80
Colour consistency Within 6 step
Macadam ellipse
Within 6 step
Macadam ellipse
Rated peak intensity 355cd 525cd
Rated beam angle >120° >120°
Voltage 240V 240V
Not suitable for accent lighting

READ THIS FIRST:
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This light tting must be installed by a competent
person in accordance with the current building
and IEE wiring regulations.
As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
This product is designed and constructed according
to the principles of the appropriate British Standard
and is intended for normal domestic service. Using
this tting in any other environments may result in
a shortened working life, for example where there
is prolonged periods of use or higher than normal
ambient temperatures such as lighting public or
shared spaces or in nursing / care home facilities.
Switch o the mains before commencing installation
and remove the appropriate circuit fuse or lock o
MCB.
This unit is suitable for indoor use only.
This product is suitable for installation on surfaces
with normal ammability e.g. wood, plasterboard
and masonry. It is not suitable for use on highly
ammable surfaces (e.g. polystyrene, textiles).
Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.
The chosen location of your new tting should allow
for the product to be securely mounted and safely
connected to the mains supply (lighting circuit).
Do not cover the tting and/or transformer with any
insulating materials.
Do not attach to surfaces which are damp, freshly
painted or otherwise electrically conductive (e.g.
metallic surfaces).
This product is designed for permanent connection
to xed wiring: this must be a suitable circuit
(protected with the appropriate MCB or fuse).
When making connections ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.
This product is double insultated. DO NOT
CONNECT ANY PART TO EARTH.
IMPORTANT:
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out,
these tests are specied in the current IEE wiring and
building regulations.
The luminaire is designed for mounting in a
ceiling, between 5-10mm thick.
INSTALLATION:
01. Locate suitable position without obstructions
(allow minimum 75mm around the hole for the
spring clips) and minimum ceiling void height of
150mm. (see Fig.1 opposite).
02. Isolate mains.
03. Make a round xing hole in the ceiling (see sizes
below), ensuring that the hole is cut accurately, we
recommend the use of a circular hole cutter.
i) RDL12: 12W unit is 160mm - 164mm diameter.
ii) RDL18: 18W unit is 220mm - 225mm diameter.
NOTE: Ensure cut-out holes are burr free before
installations.
04. Make connection to driver.
05. Before feeding the luminaire into the hole, ensure
the large spring clips point up. (See Fig. 2).
06. Feed the rest of luminaire into the hole in the
ceiling ensuring it is ush to the mounting
surface. (See Fig. 3).
07. Switch on and test the luminaire.
LAMP REPLACEMENT:
This luminaire has a sealed LED lamp and is
maintenance free, no lamp replacement is required.
3m minimum dimension between groups of panels
5m maximum dimension between groups of panels 5m max
5m is maximum area of diuser in any one 5m x 5m group
panel of diuser separated groups of panels
KEY
5m
Fig 1
12W: ø 160-164mm
18W: ø 220-225mm
75mm 75mm
5-10mm
ET 150mm
Fig 2
Fig 3
Maximum
classication
of lower
surface
Use of space
below the
diusers
Maximum
area of each
diuser panel
Max total
area of
diuser
panels as
percentage
of oor area
of the space
in which the
ceiling is
located
Minimum
separation
distance
between
diuser
panels
TP (a)
Any except
protected
stairway
No limit No limit No limit
TP (b) Rooms 5.sq m 50 3M TP (b)
Circulation
spaces except
protected
stairways
5.sq m 15 3M
LAYOUT RESTRICTIONS ON LIGHTING DIFFUSERS IN
SUSPENDED CEILINGS
LAYOUT RESTRICTIONS ON TP(b) LIGHTING DIFFUSERS
L
N