Eterna ML5040 User manual

Issue 2014
Model:
ML5040
Mirror Light With Dual Voltage Shaver Socket
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
Pack contents:
1 x Mirror light
2 x 15W G13 T8 450mm tubes
1 x Fixing kit
FOR PRODUCT ADVICE:
• T: 01933 673 144
• F: 01933 678 083
• E: [email protected].uk
Visit our website:
www.eterna-lighting.co.uk
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
874/2012
A
MODELNO.
ML5040
MODELNO.
A++
XXX kWh/1000h
18.57
ML5040
A
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
CLEANING:
Clean this light tting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.
For breakage information visit:
www.eterna-lighting.co.uk
LAMP SPECIFICATIONS:
Nominal Wattage 15W
Rated Wattage 15W
Average lifetime hours 15,000 hrs
Nominal useful luminous ux 1010 lm
Rated luminous ux 1010 lm
Luminous ecacy (Lm/W) in
50Hz operation 67
Luminous ecacy (Lm/W) in
HF operation 67
Rated lamp Lumen
maintenance
2000hrs: 95%
4000 hrs: 92%
6000 hrs: 91%
8000 hrs: 91%
12000 hrs: 85%
Rated survival factors
2000hrs: 99%
4000 hrs: 97%
6000 hrs: 95%
8000 hrs: 91%
12000 hrs: 85%
Lamp dimensions (mm) 450mm
Cap type G13
Lamp Mercury content to an
accuracy of 0.1mg ≤2.5mg
Colour rendering index Ra ≥80
Colour temperature 3000K
Ambient temperature required
to achieve maximum luminous
ux
25°C
Dimmable No
Ballast EEI A2

READ THIS FIRST:
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This product contains glass, care must be taken when
assembling, tting or handling to prevent personal
injury or damage to the product.
This light tting must be installed in accordance
with the Building Regulations making reference to
the current edition of the IEE Wiring Regulations
(BS7671). The Building Regulations may be obtained
from OPSI (Oce of Public Sector Information) or
viewed and downloaded from www.communities.
gov.uk following the link for Building Regulations.
Switch o the mains before commencing installation
and remove the appropriate circuit fuse.
This tting contains an isolating transformer rated
at 20W maximum and is only intended for use with
electric shavers. It is possible to connect other
devices to the socket outlet such as chargers for
electric toothbrushes provided they are tted
with the correct plug. Use of the socket to power
equipment requiring greater than 20W will cause
the transformer to overheat and/or stop working
altogether. Please refer to the manufacturers
instructions supplied with your appliance to
determine whether it is suitable for use in the
location where you have installed your shaver light
and that the power consumption is less than 20W.
The switch in your tting turns the light on and o.
The sockets are permanently live.
When using the shaver socket, ensure that the
correct socket is used according to the working
voltage of your appliance. Connecting your
appliance to the wrong socket could cause
permanent damage to your appliance, your tting
or both.
Suitable for indoor use only.
This tting is suitable for use in bathrooms in Zone 2
or outside. This tting must not be installed in zones
0, 1 see diagram below:
This product is suitable for installation on surfaces
with normal ammability (indicated by the “F” in a
triangle) e.g. wood, plasterboard, masonry. It is not
suitable for use on highly ammable surfaces
(e.g. polystyrene, textiles).
Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.
The chosen location of your new tting should allow
for the product to be securely mounted and safely
connected to the mains supply (lighting circuit).
The tting, especially the shaver socket, should be
placed where it cannot be splashed.
This product is designed for permanent connection
to xed wiring: this should be either a suitable
lighting circuit (protected with a 5 or 6 Amp MCB or
fuse) or a fused spur (with a 3 Amp fuse) via a fused
connection unit. We recommend that the supply
incorporates a switch for ease of operation.
Make connections to the electrical supply in
accordance with the following code:
Live - Brown or Red
Neutral - Blue or Black
Earth - Green and Yellow
This product must be connected to Earth.
When making connections, ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation. Wrap loose terminal blocks well with
insulating tape.
Disconnect the tting from the electrical supply
before ash or high voltage testing.
Suitable for indoor use only.
If the location of your new tting requires the
provision of a new electrical supply, the supply
must conform with the requirements of the Building
Regulations making reference to the current edition
of the IEE Wiring Regulations (BS7671).
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out:
these tests are specied in the Wiring Regulations
(BS7671) referred to in the Building Regulations.
INSTALLATION:
01. Choose the location for your mirror light
complying with the conditions listed opposite.
02. Lay the tting at and remove the four screws
that retain the mirror (two each side).
03. Lift the mirror o of the tting and store safely.
04. Using the metal case as a template, mark the
position of the xing holes. Laying a spirit level
across the top of the metal case will help ensure
that your mirror is installed level.
05. Prepare the xing holes as appropriate to your
mounting surface.
06. Pierce the rubber grommet in the cable entry
hole that you intend to use. Do not make the
hole too large, the rubber grommet must make a
watertight seal around the supply cable.
07. Thread the supply cable through the pierced
grommet.
08. Secure the metal case to the wall using the
xings supplied. If the xings supplied are not
appropriate to your installation, use suitable
alternatives.
09. Remove the plastic box covering the mains
terminals and shaver socket transformer.
10. Make the electrical connections according to the
colour code opposite.
11. Re-t the plastic cover over the terminals and
transformer.
12. Fit the uorescent tubes by slotting into the
lampholders and turning through approx 90° or
until they click softly into position.
13. Check that the soft gasket is correctly positioned
around the facing edge of the metal case.
14. Replace the mirror and secure in position using
the four screws removed previously. Press rmly
on the mirror to ensure a tight t against the
gasket before tightening screws.
15. Restore the power and switch on.
LAMP REPLACEMENT
1. Switch o the electricity at the mains.
2. Remove the four retaining screws (two each side)
and lift o the mirror.
3. Remove and replace tube(s). Fit the uorescent
tubes by slotting into the lampholders and turning
through approx 90° or until they click softly into
position making sure that the tube is of the same
type and wattage as stated on the relamping label.
4. Check that the soft gasket is correctly positioned
around the facing edge of the metal case.
5. Replace the mirror and secure in position using the
four screws removed previously. Press rmly on the
mirror to ensure a tight t against the gasket and
tighten the screws.
6. Restore the power and switch on.
REPLACEMENT LAMP TYPE:
Requires 2 x 15W G13 T8 450mm uorescent tubes
3000K (included).
Fitting is rated at 15W max (per lampholder).
225cm
60cm240cm
60cm
radius
from tap
ZONE 1
ZONE 0
ZONE 2
ZONE 2
Bathroom Zones Diagram