Eterna LDLEM3 User manual

Issue 2013
LAMP REPLACEMENT:
LED product is sealed and non replaceable.
BATTERY REPLACEMENT:
If after routine operation check, the lamp does not remain lit for the three hour period, a new battery pack may
be required.
1) Switch o the electricity at the mains and allow batteries to fully discharge then reconnect to supply and
allow charging for 24 hours.
2) Test again for 3 hours, if light does not remain lit, then change the battery pack as follows:
3) Isolate from mains supply and unplug the battery plug lead from the socket and re-plug the new battery.
4) Restore power and allow charging for 24 hours.
5) Perform full operation check and update test record.
REPLACEMENT BATTERY TYPE:
3.6V 2000mAh Ni-Cad - 3 x C Cell.
CLEANING:
Clean this product only with a soft dry cloth and do not use any chemical or abrasive cleaners.
EVENTUALLY, YOU MAY WANT TO REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from Electrical and Electronic Equipment (European “WEEE
Directive” eective August 2005—UK WEEE Regulations eective 2nd January 2007). Environment Agency
Registered Producer: WEE/GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE RECYCLE IT
WHERE FACILITIES EXIST  DO NOT DISPOSE WITH HOUSEHOLD WASTE.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return it to the place where you bought it. Our Technical Team
will gladly advise on any Eterna Lighting product, but may not be able to give specic instructions regarding
individual installations.
Model:
LDLEM3
LED Emergency Downlight
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
Pack contents:
1 x 1.5W LED downlight c/w
inverter and battery pack
1 x Silver trim
1 x White trim
1 x Test record sheet
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
FOR PRODUCT ADVICE:
• T: 01933 673 144
• F: 01933 678 083
• E: [email protected]o.uk
Visit our website:
www.eterna-lighting.co.uk

READ THIS FIRST:
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
Switch o the mains before commencing installation
and remove the appropriate circuit fuse or lock o
MCB.
Use only with the driver/inverter provided. Do not
connect directly to the mains.
This unit is suitable for indoor use only.
This product is designed for permanent connection
to xed wiring: this must be a suitable circuit
(protected with the appropriate MCB or fuse).
Do not cover the tting, battery and driver with any
insulating materials.
The driver should be placed where it cannot come
into contact with water or moisture.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out,
these tests are specied in the current IEE wiring and
building regulations.
INSTALLATION:
Choose the location for the new tting taking the
above points into consideration.
1) Mark the locations of your downlight and then
using an appropriate hole cutter, make a 32mm
diameter hole. (See below).
2) Prepare the route for the mains cable and feed
through the hole and make the connections to the
input side of the driver/inverter.
3) Feed the driver/inverter through the hole,
followed by the battery pack, which can lay
adjacent to the hole.
4) Feed the excess cable through the hole and press
the down light into position (see below) until it is
retained by the springs. The tting may require
some manipulation in order to pass through the
hole. Do not enlarge the hole to make tting
easier.
5) Restore the power and check tting is working
correctly. The LED will illuminate green on normal
operation, which indicates the tting is charging.
On mains power failure the LED will illuminate
white light continuously for a minimum of 3 hour
SPECIFICATION:
EBLF: 0.92
OPERATION CHECKS:
Periodic testing should be carried out monthly by simulating a failure of supply, causing the tting to be
energised from its battery. Interruption of the supply should be carried out by the operation of a local key
switch or other isolation device. During this period all ttings should be examined visually to ensure that they
are functioning correctly. At the end of the test period the supply shall be restored and all indicator lamps or
devices checked to ensure that the normal supply has been restored.
The duration of the simulated failure shall be:-
Each month:
Isolate the power supply and check the light is illuminated. This test should last for only a short period.
Endorse the test record form supplied.
Once each year:
Isolate the power supply and check that the light is still illuminated after 3 hours. Endorse the test record form.
IMPORTANT NOTE:
Please keep this instruction booklet and test record sheet with all recorded test data in a safe place.
A re ocer or other authorised person may want to see your record of inspection and testing.
DRIVER
L
E
N
BATTERY
INPUT 220-240VAC
50/60Hz
1.5W LED
Dia = 32mm
NEUTRAL
EARTH
LIVE
Ceiling
Ceiling
Clips will lock
fitting into place

INSTALLATION, MAINTENANCE AND OPERATION CHECK RECORD
Location: Installation Date: Installation Test Duration: Installed By:
Month Test
Year: Year: Year: Year: Year:
Sign Date Sign Date Sign Date Sign Date Sign Date
1 Short 2 Short 3 Short 4 Short 5 Short 6 Short 7 Short 8 Short 9 Short
10 Short 11 Short 12 3 hr endurance