EtherWAN EX32908 series User manual

EX32908 series www.etherwan.com
Quick Start Guide
This quick start guide describes how to install and use the
Industrial Gigabit Ethernet Switch. Capable of operating at
temperature extremes of -10°C to +60°C, this is the switch of
choice for harsh environments constrained by space.
Physical Description
The Port Status LEDs
1

EX32908 series www.etherwan.com
LED State Indication
Steady Power on.
Power (Green) Off Power off.
Steady Relay Starts alarm.
Fault (Red) Off Relay non-alarm.
Gigabit Ports
Steady A valid network connection established.
10/100Mbps: Green, 1000Mbps: Amber.
Blinking Transmitting or receiving data.
Act stands for Activity.
Link/Act
Off No link.
The Terminal Block and Power Inputs
Power Input Assignment
＋12~48VDC
Power1
－Power Ground
＋12~48VDC
Power2
－Power Ground
Earth Ground
Terminal Block
Relay Output Rating 1A @ 250VAC
2

EX32908 series www.etherwan.com
DC Terminal Block Power Input: The DC Terminal Block
power input can be used to power up this Switch.
DIP Switch Settings
DIP No. On Off
1 Port 1 Alarm Enable. Port 1 Alarm Disable.
2 Port 2 Alarm Enable. Port 2 Alarm Disable.
3 Port 3 Alarm Enable. Port 3 Alarm Disable.
4 Port 4 Alarm Enable. Port 4 Alarm Disable.
5 Port 5 Alarm Enable. Port 5 Alarm Disable.
6 Port 6 Alarm Enable. Port 6 Alarm Disable.
7 Port 7 Alarm Enable. Port 7 Alarm Disable.
8 Port 8 Alarm Enable. Port 8 Alarm Disable.
The Gigabit Ethernet Connectors
The 10/100/1000Base-TX Connections
The following lists the pinouts of 10/100/1000Base-TX
ports.
3

EX32908 series www.etherwan.com
Pin Signal Name Signal Definition
1 TP0＋Transmit and Receive Data 0 ＋
2 TP0－Transmit and Receive Data 0 －
3 TP1＋Transmit and Receive Data 1 ＋
4 TP2＋Transmit and Receive Data 2 ＋
5 TP2－Transmit and Receive Data 2 －
6 TP1－Transmit and Receive Data 1 －
7 TP3＋Transmit and Receive Data 3 ＋
8 TP3－Transmit and Receive Data 3 －
The 1000Base-SX/LX Connections
The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx
(receive) port of device I to the Tx (transmit) port of device II.
The WDM 1000Base-BX Connections
The fiber port pinouts: Only one optical fiber is required to
transmit and receive data.
4

EX32908 series www.etherwan.com
5
Functional Description
Complies with EN61000-6-2 & EN61000-6-4 EMC
Generic standard immunity for industrial environment.
Supports 802.3/802.3u/802.3ab/802.3z/802.3x.
Auto-negotiation: 10/100/1000Mbps, Full/Half-duplex.
Auto MDI/MDIX.
1000Base-SX/LX: Multi mode SC or ST type, Single
mode SC type. 1000Base-BX: WDM Single mode SC
type.
Supports 4096 MAC addresses, 192K Bytes buffer
memory.
Supports IEEE802.3az Energy Efficient Ethernet (EEE).
High speed, non-blocking four traffic class QoS switch
fabric.
Supports Jumbo frame up to 9720 Bytes.
Power Supply: Redundant 12~48VDC Terminal Block
power inputs.
Power consumption: 6.5W Max.
Provides reverse polarity protection.
Provides overload current protection.
Operating temperature ranges from -10°C to 60°C
(14°F to 140°F).
Slim design with DIN-Rail mount installation.

EX32908 series www.etherwan.com
Assembly, Startup, and Dismantling
Assembly: Place the switch on the DIN rail from above
using the slot. Push the front of the switch toward the
mounting surface until it audibly snaps into place.
Startup: Connect the supply voltage to start up the
switch via the terminal block.
Dismantling: Pull out the lower edge and then remove
the switch from the DIN rail.
6

EX32908 series www.etherwan.com
7
Preface
A member of the growing family of rugged switches, this
switch addresses a need for a smaller switch. This switch
provides an affordable solution for rugged and outdoor
environment, transportation road-side cabinet, industrial floor
shop, multitenant dwellings or Fiber To The Home (FTTH)
applications. Capable of operating at temperature extremes of
-10°C to +60°C, this is the switch of choice for harsh
environments constrained by space.
Plug-and-Play Solution:
The switch is a plug-and-play Industrial Gigabit Ethernet
Switch in compact size. It doesn't have any complicated
software to set up.
This manual describes how to install and use the Industrial
Gigabit Ethernet Switch. This switch integrates full wire speed
switching technology. This switch brings the answer to
complicated hardened networking environments.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
Features on the switch
Illustrative LED functions
Installation instructions
Specifications

EX32908 series www.etherwan.com
8
Table of Contents
QUICK START GUIDE 1
PHYSICAL DESCRIPTION 1
The Port Status LEDs 1
The Terminal Block and Power Inputs 2
DIP Switch Settings 3
The Gigabit Ethernet Connectors 3
FUNCTIONAL DESCRIPTION 5
ASSEMBLY,STARTUP,AND DISMANTLING 6
PREFACE 7
TABLE OF CONTENTS 8
PRODUCT OVERVIEW 9
INDUSTRIAL GIGABIT ETHERNET SWITCH 9
PACKAGE CONTENTS 9
PRODUCT HIGHLIGHTS 10
Basic Features 10
FRONT PANEL DISPLAY 11
PHYSICAL PORTS 12
INSTALLATION 13
SELECTING A SITE FOR THE SWITCH 13
DIN RAIL MOUNTING 14
CONNECTING TO POWER 15
DC Terminal Block Power Inputs 15
CONNECTING TO YOUR NETWORK 17
Cable Type & Length 17
Cabling 18
SPECIFICATIONS 19

EX32908 series www.etherwan.com
Product Overview
Industrial Gigabit Ethernet Switch
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
This Switch
User’s Manual
9

EX32908 series www.etherwan.com
10
Product Highlights
Basic Features
Complies with EN61000-6-2 & EN61000-6-4 EMC
Generic standard immunity for industrial environment.
Supports 802.3/802.3u/802.3ab/802.3z/802.3x.
Auto-negotiation: 10/100/1000Mbps, Full/Half-duplex.
Auto MDI/MDIX.
1000Base-SX/LX: Multi mode SC or ST type, Single
mode SC type. 1000Base-BX: WDM Single mode SC
type.
Supports 4096 MAC addresses, 192K Bytes buffer
memory.
Supports IEEE802.3az Energy Efficient Ethernet (EEE).
High speed, non-blocking four traffic class QoS switch
fabric.
802.1Q VLAN Tag Based Priority, Class of
Service.
Output Queue Schedule Mode: Weighted Round
Robin (WRR) with 4 priority queues.
The configurations of QoS are as below:
CoS Field Value Packet Count Priority
0 or 1 1 Lowest
2 or 3 2 Low
4 or 5 4 High
6 or 7 8 Highest
Supports Jumbo frame up to 9720 Bytes.
Power Supply: Redundant 12~48VDC Terminal Block
power inputs.
Power consumption: 6.5W Max.
Provides reverse polarity protection.
Provides overload current protection.
Operating temperature ranges from -10°C to 60°C
(14°F to 140°F).

EX32908 series www.etherwan.com
Slim design with DIN-Rail mount installation.
Front Panel Display
 Power Status (Power)
This LED comes on when the switch is properly connected to power and
turned on.
 Port Status LEDs
11

EX32908 series www.etherwan.com
The LEDs display status for each respective port.
LED State Indication
Steady Power on.
Power (Green) Off Power off.
Steady Relay Starts alarm.
Fault (Red) Off Relay non-alarm.
Gigabit Ports
Steady A valid network connection established.
10/100Mbps: Green, 1000Mbps: Amber.
Blinking Transmitting or receiving data.
Act stands for Activity.
Link/Act
Off No link.
Physical Ports
This switch provides:
Eight 10/100/1000Base-TX ports
Seven 10/100/1000Base-TX ports + one
1000Base-SX/LX/BX port
Connectivity
RJ-45 connectors
SC or ST connector on 1000Base-SX/LX fiber port
SC connector on 1000Base-BX fiber port
12

EX32908 series www.etherwan.com
13
Installation
This chapter gives step-by-step instructions about how to
install the switch:
Selecting a Site for the Switch
As with any electric device, you should place the switch
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the site
you select should meet the following requirements:
The ambient temperature should be between -10 to 60
degrees Celsius.
The relative humidity should be less than 95 percent,
non-condensing.
Surrounding electrical devices should not exceed the
electromagnetic field (RFC) standards.
Make sure that the switch receives adequate ventilation.
Do not block the ventilation holes on each side of the
switch.
The power outlet should be within 1.8 meters of the
switch.

EX32908 series www.etherwan.com
DIN Rail Mounting
Installation: Place the switch on the DIN rail from above using
the slot. Push the front of the switch toward the mounting
surface until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the switch
from the DIN rail.
14

EX32908 series www.etherwan.com
Connecting to Power
DC Terminal Block Power Inputs
Connect the DC power cord to the plug-able terminal
block on the switch, and then plug it into a standard DC
outlet.
Disconnect the power cord if you want to shut down the
switch.
Power Input Assignment
＋12~48VDC
Power1
－Power Ground
＋12~48VDC
Power2
－Power Ground
Earth Ground
Terminal Block
Relay Output Rating 1A @ 250VAC
CAUTION: This equipment is designed to permit the
connection of the earthed conductor of the DC supply circuit
to the earthing conductor at the equipment.
15

EX32908 series www.etherwan.com
16
If this connection is made, all of the following conditions must
be met:
This equipment shall be connected to directly to the DC
supply system earthing electrode conductor or to a
bonding jumper from an earthing terminal bar or bus to
which the DC supply system earthing electrode conductor
is connected.
This equipment shall be located in the same immediate
area (such as, adjacent cabinets) as any other equipment
that has a connection between the earthed conductor of
the same DC supply circuit and the earthing conductor,
and also the point of earthing of the DC system. The DC
system shall not be earthed elsewhere.
The DC supply source is to be located within the same
premises as the equipment.
Switching or disconnecting devices shall not be in the
earthed circuit conductor between the DC source and the
point of connection of the earthing electrode conductor.

EX32908 series www.etherwan.com
17
Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications below when
connecting the switch to your network. Use appropriate
cables that meet your speed and cabling requirements.
Cable Specifications
Speed Connector Port
Speed
Half/Full
Duplex
Cable Max.
Distance
10Base-T RJ-45 10/20 Mbps 2-pair
UTP/STP
Cat. 3, 4, 5
100 m
100Base-TX RJ-45 100/200
Mbps
2-pair
UTP/STP
Cat. 5
100 m
1000Base-T RJ-45 2000 Mbps 4-pair
UTP/STP
Cat. 5, 5e
100 m
1000Base-SX SC, ST 2000 Mbps MMF (50 or
62.5μm)
220, 550 m
or
2 km
1000Base-LX SC, ST 2000 Mbps SMF (9 or
10μm)
10, 30, 40
km
1000Base-BX SC 2000 Mbps SMF (9 or
10μm)
70 km

EX32908 series www.etherwan.com
18
Cabling
Step 1: First, ensure the power of the switch and end devices are turned off.
<Note> Always ensure that the power is off before any installation.
Step 2: Prepare cable with corresponding connectors for each type of port
in use.
<Note> To connect two regular RJ-45 ports between switches or hubs, you need a
straight or cross-over cable.
Step 3: Consult the previous section for cabling requirements based on
connectors and speed.
Step 4: Connect one end of the cable to the switch and the other end to a
desired device.
Step 5: Once the connections between two end devices are made
successfully, turn on the power and the switch is operational.

EX32908 series www.etherwan.com
19
Specifications
Industrial Compact
Switch
10/100/1000Base-TX auto-negotiating ports
with RJ-45 connectors, 1000Base-SX/LX/BX
fiber port
Applicable Standards IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE802.3ab 1000Base-T
IEEE802.3z 1000Base-SX/LX
Forwarding Rate
10Base-T:
100Base-TX:
1000Base-T:
1000Base-SX/LX/BX:
10 / 20Mbps Half / Full-duplex
100 / 200Mbps Half / Full-duplex
2000Mbps Full-duplex
2000Mbps Full-duplex
Performance 148,80pps for 10Mbps
148,810pps for 100Mbps
1,488,100pps for 1000Mbps
Cable
10Base-T:
100Base-TX:
1000Base-T:
1000Base-SX/LX/BX:
2-pair UTP/STP Cat. 3, 4, 5
2-pair UTP/STP Cat. 5
4-pair UTP/STP Cat. 5, 5e
Up to 100m (328ft)
MMF (50 or 62.5μm), SMF (9 or10μm)
LED Indicators Per unit – Power (Green), Fault (Red)
Per port – 10/100Mbps: Link/Act (Green)
1000Mbps: Link/Act (Amber)
Dimensions 35mm (W) × 86mm (D) × 149mm (H)
(1.4” (W) × 3.44” (D) × 5.96” (H))
Net Weight 0.3Kg (0.66lb.)
Power Terminal Block: 12-48VDC
Power Consumption 6.5W Max.
Operating Temperature -10°C to 60°C (14°F to 140°F)
Tested @ -20°C to 70°C (-4°F to 158°F)
Storage Temperature -25°C to 85°C (-13°F to 185°F)
Humidity 5%-95% non-condensing

EX32908 series www.etherwan.com
20
EMI FCC Part 15, Class A
VCCI
EN61000-6-4:
EN55022, EN61000-3-2, EN61000-3-3
EMS EN61000-6-2:
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)
Environmental Test
Compliance
IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
FED STD 101C Method 5007.1 (Free Fall with
package)