evertz 7700 MultiFrame User manual

7700/7800 MultiFrame
7800DA2T-3G 3G/HD/SD-SDI Distribution Amplifier
User Manual
© Copyright 2018
EVERTZ MICROSYSTEMS LTD.
5292 John Lucas Drive
Burlington, Ontario
Canada L7L 5Z9
Phone: [phone]
Sales: [e-mail] Fax: [phone]
Tech Support: [e-mail] Fax: [phone]
Web Page: http://www.evertz.com
Version 1.0, August 2018
The material contained in this manual consists of information that is the property of Evertz Microsystems and is intended solely for the use of
purchasers of the 7800DA2T-3G product. Evertz Microsystems expressly prohibits the use of this manual for any purpose other than the
operation of the 7800DA2T-3G product. Due to on going research and development, features and specifications in this manual are subject to
change without notice.
All rights reserved. No part of this publication may be reproduced without the express written permission of Evertz Microsystems Ltd. Copies of
this manual can be ordered from your Evertz dealer or from Evertz Microsystems.

This page left intentionally blank

IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “Dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (Servicing) instructions
in the literature accompanying the product.
•Read these instructions
•Keep these instructions.
•Heed all warnings.
•Follow all instructions.
•Do not use this apparatus near water
•Clean only with dry cloth.
•Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
•Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
•Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than other. A grounding-type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
•Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles and the point where they exit from the apparatus.
•Only use attachments/accessories specified by the manufacturer
•Unplug this apparatus during lightning storms or when unused for long periods of time.
•Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC –
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE
WARNING
DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING AND ENSURE THAT NO
OBJECTS FILLED WITH LIQUIDS ARE PLACED ON THE EQUIPMENT
WARNING
TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT THE
POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE
WARNING
THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE

INFORMATION TO USERS IN EUROPE
NOTE
CISPR 22 CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to the European Union EMC directive. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
INFORMATION TO USERS IN THE U.S.A.
NOTE
FCC CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
WARNING
Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could void the user’s
authority to operate the equipment.
Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface cables
with the shield connected to the chassis ground of the device must be used.
EN60065
Safety
EN504192 2005
Waste electrical products should not be
disposed of with household waste.
Contact your Local Authority for recycling
advice
EN55103-1: 1996
Emission
EN55103-2: 1996
Immunity

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Page - i Revision 1.0
TABLE OF CONTENTS
1. OVERVIEW ...................................................................................................................................1
2. INSTALLATION.............................................................................................................................3
3. SPECIFICATIONS.........................................................................................................................5
3.1. SERIAL VIDEO INPUT .........................................................................................................5
3.2. SERIAL VIDEO OUTPUTS...................................................................................................5
3.3. ELECTRICAL .......................................................................................................................6
3.4. PHYSICAL............................................................................................................................6
4. STATUS LEDS..............................................................................................................................7
5. CARD EDGE MODULE CONTROL...............................................................................................9
5.1. CARD-EDGE CONTROL......................................................................................................9
5.1.1. Navigating the Card-Edge..........................................................................................9
5.2. CARD-EDGE MENU STRUCTURE ......................................................................................9
5.3. SETTING THE DISPLAY ORIENTATION.............................................................................9
5.4. PRESET PARAMETERS....................................................................................................10
5.4.1. Saving Presets ........................................................................................................10
5.4.2. Loading Presets.......................................................................................................10
6. VISTALINK®MODULE CONTROL .............................................................................................11
6.1. WHAT IS VISTALINK®? .....................................................................................................11
6.2. GENERAL...........................................................................................................................12
6.2.1. Information...............................................................................................................12
6.3. VIDEO CONTROL ..............................................................................................................13
6.4. PRESETS CONTROL.........................................................................................................14
6.4.1. Presets ....................................................................................................................14
6.5. MONITOR...........................................................................................................................15
6.5.1. Video Status............................................................................................................15

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Page - ii Revision 1.0
6.6. INPUT 1 FAULT TRAPS.....................................................................................................16
6.7.INPUT 2 FAULT TRAPS.....................................................................................................17
7. JUMPERS AND USER ADJUSTMENTS ....................................................................................19
7.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED BY THE GLOBAL FRAME
STATUS .............................................................................................................................19
7.2. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES.........................................19
8. UPGRADE PROCEDURES.........................................................................................................21
8.1. UPGRADE FIRMWARE......................................................................................................21
8.2. UPDATING VLPRO SERVER JAR FILE............................................................................22
Figures
Figure 1-1 : 7800DA2T-3G Block Diagram.....................................................................................2
Figure 2-1 : 7800DA2T-3G/7800DA2T-HD Rear Panels................................................................3
Figure 4-1 : Status LEDs................................................................................................................7
Figure 6-1 : VistaLINK®PRO - General Section...........................................................................12
Figure 6-2 : VistaLINK®PRO - Video Control Section..................................................................13
Figure 6-3 : VistaLINK®PRO - Presets Control Section...............................................................14
Figure 6-4 : VistaLINK®PRO - Monitor Section............................................................................15
Figure 6-5 : VistaLINK®PRO - Input 1 Fault Traps Section..........................................................16
Figure 6-6 : VistaLINK®PRO - Input 2 Fault Traps Section..........................................................17
Figure 7-1 : LED and Jumper Locations.......................................................................................19
Figure 8-1 : VistaLINK®PRO - Version information selection.......................................................21
Figure 8-2 : VistaLINK®PRO - Version Information Window........................................................22
Figure 8-3 : VistaLINK®PRO - Upgrade Firmware Window .........................................................22
Figure 8-4 : VistaLINK®PRO Server/Apply Update......................................................................23
Figure 8-5 : VistaLINK®PRO – Applying JAR Updates................................................................23

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Page - iii Revision 1.0
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 First Revision Aug 2018
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for
the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning performance of
Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The only warranty offered
by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no warranty is
granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or order confirmation.
Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If you encounter an error,
please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make changes in equipment design or
specifications.

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Page - iv Revision 1.0
This page left intentionally blank

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Revision 1.0 Page - 1
1. OVERVIEW
The 7800DA2T Dual 3G/HD/SD-SDI Reclocking Distribution Amplifier provides high quality distribution of
facility 3G/HD/SD-SDI signals. HD versions support SMPTE ST 292-1 and SMPTE ST 259 signals while
3G versions also support SMPTE 424M signals. This module features dual auto-sensing equalized inputs
with unparalleled cable equalization, making it the most-cost effective and ideal solution for long cable run
environments.
The included dual bypass relays offer failure proof protection for critical paths.
For maximum flexibility, the module can operate in a dual input to three outputs each configuration or as
one input to six output configuration.
The 7800DA2T is VistaLINK®enabled, offering remote monitoring, control and configuration capabilities
via Simple Network Management Protocol (SNMP) giving the flexibility to manage operations, including
signal monitoring and module configuration from SNMP capable control systems (Manager or NMS).
The 7800DA2T occupies one card slot and can be housed in the 3RU 7700FR-C, 7800FR and 7800FR-
QT frames that have a 15-slot capacity. The 7700FC frame controller is required for configuration.
Features:
•HD/SD-SDI dual input with three reclocked outputs per input
•Bypass relay protection included for both inputs
•Support for common 3G-SDI video inputs (-3G versions)
•Configurable as one DA with six outputs or two DAs with three outputs each (1x6 or 2 - 1x3)
•Industry leading long reach cable performance
•Input signal presence detection
•High density approach offers 14 modules within 3RU (28 DA’s in 3RU)
•Real time VistaLINK®monitoring and trending for SNMP monitoring

NOTE: From this point forward, the 7800DA2T-3G and the 7800DA2T-HD modules will be
referred to as the 7800DA2T, unless the feature in question is applicable only to one of the
modules, in which case the specific model number will be referenced.

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Page - 2 Revision 1.0
Figure 1-1 : 7800DA2T-3G Block Diagram

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Revision 1.0 Page - 3
2. INSTALLATION
The 7800DA2T comes with a companion rear plate that occupies one slot in the frame. For information
on inserting the module into the frame see section 3 of the 7800FR chapter.
Figure 2-1 : 7800DA2T-3G/7800DA2T-HD Rear Panels
3G/HD/SD-SDI INPUT: There are two input DIN 1.0/2.3 connectors for 10-bit serial digital video
signals compatible with the 3Gb/s SMPTE 424M, 1.5Gb/sec SMPTE 292M,
and 270Mb/s SMPTE 259M-C (525i/59.94 or 625i/50) standard.
3G/HD/SD-SDI OUTPUT: There are six DIN 1.0/2.3 connectors with reclocked serial digital video
outputs, compatible with the 3Gb/s SMPTE 424M, 1.5Gb/sec SMPTE 292M,
and 270Mb/s SMPTE 259M-C (525i/59.94 or 625i/50) standard.

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Page - 4 Revision 1.0
This page left intentionally blank

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Revision 1.0 Page - 5
3. SPECIFICATIONS
3.1. SERIAL VIDEO INPUT
Standard: Auto-detects standard 3Gb/s SMPTE 424M, 1.5Gb/sec SMPTE 292M, 270Mb/s
SMPTE 259M-C (525i/59.94 or 625i/50)
Connector: 1 DIN 1.0/2.3 connector (1x6 mode)
2 DIN 1.0/2.3 connectors (2 by 1x3 mode)
Input Equalization: Automatic to
150m @ 3Gb/s (Belden 1694A cable)
200m @ 1.5Gb/s (Belden 1694A cable)
380m @ 270Mb/s (Belden 1694A cable)
Return Loss: > 10dB up to 3Gb/s
> 15dB up to 1.5Gb/s
> 20dB up to 270 Mb/s
3.2. SERIAL VIDEO OUTPUTS
Standard: Auto-detects standard 3Gb/s SMPTE 424M, 1.5Gb/sec SMPTE 292M, 270Mb/s
SMPTE 259M-C (525i/59.94 or 625i/50)
Number of Outputs: 3 per path (2 by 1x3 mode)
6 (1x6 mode)
Connector: DIN 1.0/2.3 connector
Signal Level: 800mV nominal
DC Offset: 0V ±0.5V
Rise and Fall Time: 200ps nominal for 3G/HD-SDI
900ps nominal for SD-SDI
Overshoot: < 10% of amplitude
Return Loss: > 10dB for 1.5 - 3Gb/s
> 20dB up to 1.5Gb/s
Alignment Jitter: < 0.3 UI for SMPTE 424M
< 0.20 UI for SMPTE 259M and 292M

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Page - 6 Revision 1.0
3.3. ELECTRICAL
Voltage: + 12VDC
Power: 6 Watts
EMI/RFI: Complies with FCC regulations for class A devices
Complies with EU EMC directive
3.4. PHYSICAL
Number of slots:
350FR: 1
7700-FR-C: 1
7800FR: 1
7800FR-QT: 1
7801FR: 1

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Revision 1.0 Page - 7
4. STATUS LEDS
The 7800DA2T has eight LED status indicators on the front card edge to show operational status of the
card at a glance. Figure 4-1 shows the location of the LEDs.
Two large Module Status LEDs on the front of the board indicate the general health of the module:
LOCAL FAULT: This Red LED indicates poor module health and will be On during the absence of a
valid input signal (on either of the two inputs if in dual 1x4 mode) or if a local input
power fault exists (i.e.: a blown fuse). The LOCAL FAULT indication can also be
reported to the frame through the FRAME STATUS jumper.
MODULE OK: This Green LED indicates good module health. It will be On when a valid input
signal is present (on both inputs if in dual 1x4 mode), and board power is good.
There are 18 small LEDs that are not currently implemented. Figure 4-1 identifies the function of some of
the status LEDs present on the board.
7800IDA2Q-3G
Shaft
Encoder
Module
Status 4 Character
Dot Matrix
Display
Figure 4-1 : Status LEDs

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Page - 8 Revision 1.0
This page left intentionally blank

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Revision 1.0 Page - 9
5. CARD EDGE MODULE CONTROL
5.1. CARD-EDGE CONTROL
The 7800DA2T is equipped with a push-button shaft encoder and a four character dot matrix display to
control various functions on the card. The push-button shaft encoder is used to navigate through a menu
system to set and monitor various parameters for the module. When not in the menu system the four
character dot matrix display rotates through the module name, firmware version and IP address.
5.1.1. Navigating the Card-Edge
You can use the push-button shaft encoder to move up and down the list of available parameters to
adjust. To adjust any parameter, use the shaft encoder to move up or down to the desired parameter and
then press the shaft encoder in. If the parameter is a numerical value, the number will increase if you
rotate the shaft encoder clockwise and decrease if you rotate the shaft encoder counter-clockwise. If the
parameter contains a list of options, you can cycle through the list by rotating the shaft encoder in either
direction. The parameter values are changed as you cycle through the list.
When you have stopped at the desired value, depress the shaft encoder. This will return you to the
parameter, select the menu item that you are setting (the display shows the parameter name you were
setting). To change another parameter, rotate the shaft encoder to select other parameters. If neither the
toggle switch nor pushbutton is operated for several seconds the card edge control will exit the menu
system and return to an idle state.
Throughout the descriptions of the Menu items, default values are shown with bolded text.
5.2. CARD-EDGE MENU STRUCTURE
The following is a brief description of the top level of the menu tree that appears when you enter the ON
screen menu. Selecting one of these items will take you down into the next menu level to set the value of
that parameter.
DSPL
Sets the orientation of the four-digit LED display
PRST
Allows the saving or recalling of presets
QUIT
Exits the menu
5.3. SETTING THE DISPLAY ORIENTATION
The DSPL parameter controls the display orientation of the four digit LED display.
HORZ The display will be shown horizontally (ideal when installed in a 1RU or
standalone frame).
VERT The display will be shown vertically (ideal when installed in a 3RU frame).

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Page - 10 Revision 1.0
5.4. PRESET PARAMETERS
The PRST menu option enters into a selection menu to either recall or save a preset.
SAVE Menu option to save current module state to a selected preset.
LOAD Menu option to load to the module a selected preset.
5.4.1. Saving Presets
The SAVE parameter will save the current module settings to a selected preset number. The user can
save the settings by assigning a preset number (i.e. Preset 02), which can later be recalled using the load
parameter.
01-10 Selects the preset to save the current module settings to.
5.4.2. Loading Presets
The LOAD parameter will load the settings saved in the preset to the current module settings. The user
can recall and load a saved preset by selecting the desired preset number (i.e. Preset 02).
FACT Loads the factory default settings into the module.
01-10 Selects the preset from which to load settings from.

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Revision 1.0 Page - 11
6. VISTALINK®MODULE CONTROL
This section describes the VistaLINK®control and monitoring available on the 7800DA2T.
6.1. WHAT IS VISTALINK®?
VistaLINK®is Evertz’s remote monitoring and configuration platform which operates over an Ethernet
network using Simple Network Management Protocol (SNMP). SNMP is a standard computer network
protocol that enables different devices sharing the same network to communicate with each other.
VistaLINK®provides centralized alarm management, which monitors, reports, and logs all incoming alarm
events and dispatches alerts to all the VLPro Clients connected to the server. Card configuration through
VistaLINK®PRO can be performed on an individual or multi-card basis using simple copy and paste
routines, which reduces the time to configure each module separately. Finally, VistaLINK®enables the
user to configure devices in the network from a central station and receive feedback that the configuration
has been carried out.
There are 3 components of SNMP:
1. An SNMP manager also known as a Network Management System (NMS) is a computer running
special software that communicates with the devices in the network. Evertz VistaLINK®Pro Manager
graphical user interface (GUI), third party or custom manager software may be used to monitor and
control Evertz VistaLINK®enabled products.
2. Managed devices, each with a unique address (OID), communicate with the NMS through an SNMP
Agent. Evertz VistaLINK®enabled 7700/7800 series modules reside in the 3RU 7800FR MultiFrame
and communicate with the manager via the 7700FC VistaLINK®frame controller module, which serves
as the Agent.
3. A virtual database known as the Management Information Base (MIB) lists all the variables being
monitored, which both the Manager and Agent understand. Please contact Evertz for further
information about obtaining a copy of the MIB for interfacing to a third party Manager/NMS.
For more information on connecting and configuring the VistaLINK®network, see the 7700FC Frame
Controller chapter.

7700/7800 MultiFrame Manual
7700/7800 MultiFrame
Page - 12 Revision 1.0
6.2. GENERAL
The General section shows miscellaneous parameters of the module.
Figure 6-1 : VistaLINK®PRO - General Section
6.2.1. Information
Card Name: Indicates the product model number of the card (including installed options).
Firmware Creation Date: Indicates the build date of the firmware version.
Firmware Version: Indicates the currently installed firmware version.
Board Name: Indicates the product hardware version of the module.
Board Revision: Indicates the hardware version of the module.
Board Serial Number: Indicates the physical serial number of the module.