fantastic furniture REED CUPBOARD 2 DOOR BASE User manual

0.1noisreV
REED
CUPBOARD 2 DOOR BASE
fantasticfurniture.com.au

Page2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
fantasticfurniture.com.au
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Weight Limit: 20kgs per shelf
fantasticfurniture.com.au Page 3
Warning: Ensure the wall strap is
attached to avoid serious injury.
To avoid any serious of fatal injury, a wall strap has been provided with
this product to prevent topping. We strongly recommend that this
product is permanently fixed to the wall or other suitable surface. Fixing
of what fixing device to use.

Page 4
Read through the instructions
carefully before you begin.
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screwsuntil the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a so t surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
components please visit our website Help Centre for further assistance.
Assembly Checklist
!Please see page 3 for any safety requirements or weight restrictions.
fantasticfurniture.com.au
Useful information

(P5)
16 x Cam Nuts
Page 5
What You Need
to assemble the product
Other tools you need
Phillips head
screwdriver;Hammer.
Le t Side Panel (P1); Right Side Panel (P2);
Le t Door Panel (P9);
Back Panel (P6); Shelf Panel (P7);
16 x Cam Bolts 12 x Dowels 4 x Hinges 16 x Screws 4 x Shelf Supports 2 x Handles
4 x Screws 34 x Nails 1 x Wall Strap
1 x Wall Strap
Screw 6 x Leg Stud
s 2 x Washers
Le t Side Panel
Right Side Panel
(P2)
(P3)
(P1)
Shelf Panel
(P7)
Back Panel
(P6)
Support Panel
(P5)
Right Door Panel
(P10)
Le t Door Panel
Bottom Panel (P9)
(P4)
Top Panel (P3); Bottom Panel (P4); Support Panels (P5)x2;
(P8)
(H1) (H2) (H3) (H4) (H5) (H6) (H7)
(H8) (H9) (H10) (H11) (H12) (H13)
Right Door Panel (P10),
Steel Bar (P8);
Steel Bar
fantasticfurniture.com.au
Box :
Hardware Pack :
Support Panel
Top Panel

(H3)
Page6
Step 1
Step 2
You will need
4 x Dowels
You will need
Phillips head
screwdriver
4 x Hinges
(H4) (H5)
8 x Screws
2 x Handles
(H7) (H8)
4 x Screws
(H1)
(H3)
8 x Cam Bolts
(H1)
(P10)
(P9)
(P1)
(P2)
(H1)
(H3)
(H1)
(H3)
(H2)
(H1)
(H2)
(H2)
(H2)
(H2)
(H2)
(H8)
(H7)
(H7)
(H4) (H4)
(H5)
(H5)
(H8)
(H8)
Attach 4 x Hinges (H4) to Left & Right Door Panels (P9&P10) as shown with 8 x Screws (H5)
Secure 2 x Handles (H7) to the front of Left & Right Door Panels (P9&P10) with 4 x Handle
by tightening with the Phillips Head Screwdriver.
Screws (H8) by tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au
4 x Cam Nuts
(H4)
(H5)
(H4)
(H5)
(H5)
(H4)
(H5)
(H3)
(H1)
(H1)
(H3)
Insert 4 x Dowels (H3) & 4 x Cam Nuts (H1) into Left & Right Side Panels (P1&P2) as
shown. Attach 8 x Cam Bolts (H2) to Left & Right Side Panels (P1&P2) by tightening
with the Phillips Head Screwdriver.
(H2)

Page 7
Step 3
You will need
2 x Cam Bolts
4 x Dowels Phillips head
screwdriver
(H1) (H2)
(H3)
(P5)
(P4)
(H1)
(H1)
(H1)
(H3)
(H3)
(H1)
(H1)
(H1)
(H3)
(H3)
(H3)
(H3)
(H1)
(H2)
(H2)
Step 4
You will need
4 x Dowels
Phillips head
screwdriver
(H1) (H3)
Insert 4 x Dowels (H3) & 4 x Cam Nuts (H1) into Bottom Panel (P4) as shown.
Attach 2 x Cam Bolts (H2) to Bottom Panel (P4) by tightening with the Phillips Head
Screwdriver.
Insert 4 x Dowels (H3) & 8 x Cam Nuts (H1) into Support Panels (P5x2) as shown.
fantasticfurniture.com.au
4 x Cam Nuts
8 x Cam Nuts
(P5)
(H1)
(H1)
(H1)
(H3)
(H3)
(H1)

Step 5
Page 8
Step 6
You will need
Phillips head
screwdriver
(P4)
(P5)
You will need
fantasticfurniture.com.au
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut.You
then turn the cam
nut so it tightens
over the bolt.
(P4)
(P1)
(P2)
(P5)
(P5)
(H3)
(H1)
(H2)
(H3)
(H1)
(H2)
Ensure the raw edges of the
shelves are facing towards
the back of the unit”
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
Ensure Cam Nuts
are facing
underneath the
cabinet like shown.
(H1)
(H1)
Phillips head
screwdriver
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut.You
then turn the cam
nut so it tightens
over the bolt.
(H2)
(H2)
Attach Support Panel (P5) to Bottom Panel (P4) by tightening 2 x Cam Nuts (H1) with the
Attach Bottom Panel (P4) and Support Panels (P5x2) to Left & Right Side Panels (P1&P2)
and secure by tightening all 8 x Cam Nuts (H1) with the Phillips Head Screwdriver.
Phillips Head Screwdriver.

Page 9
Step 7
Step 8
You will need
Phillips head
screwdriver
(P3)
(H2)
6 x Cam Bolts (H2)
(H2)
fantasticfurniture.com.au
(H2)
(H2)
(H2)
(H2)
(P2)
(P1)
(P8)
(P3)
(H2)
(H1)
(H3)
You will need
Phillips head
screwdriver
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
Attach 6 x Cam Bolts (H2) to Top Panel (P3) by tightening with the Phillips Head
Screwdriver.
Place the Steel Bar (P8) into the grooves of Left & Right Side Panels (P1&P2). Align the
Top Panel (P3) with Support Panel (P5) and Left & Right Side Panels (P1&P2) and
attach by tightening the 6 x Cam Nuts (H1).

the edge of the Back Panel (P6).
Page 10
Step 9
Step 10
You will need
Hammer
fantasticfurniture.com.au
You will need
Hammer
32 x Nails
(H9)
5
5
(P2)
(P1)
(P6)
WARNING:ENSURETHE WALLSTRAPIS
ATTACHEDTOAVOIDSERIOUSINJURY.
Toavoidanyseriousorfatalinjury,thisproducthasbeen
fittedwithawallstraptopreventtoppling.Westrongly
recommendthatthisproductispermanently fixed tothe
wallor other suitable surface. Fixing devicesare not
includedsincedierentsurfacematerialsrequire
di erentattachments.Pleaseseekprofessionaladvice
ifyouare in doubtof whatfixing devicetouse.
COUNTRYOFORIGIN
CHINA
IMPORTEDBY
FHLDistributionCentrePtyLtd
71Seville Street
FAIRFIELDEAST
NSW2165
AUSTRALIA
PO#:ABC123
(P4)
(H9)
(H9)
(H9)
(H9)
outwards
Ensure the raw edge
of back panel is facing
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
(H9)
6 x Leg Studs
(H12)
WARNING:ENSURETHEWALLSTRAPIS
ATTACHEDTOAVOIDSERIOUSINJURY.
Toavoidanyseriousorfatalinjury,thisproducthasbeen
fittedwithawallstraptopreventtoppling.Westrongly
recommendthatthisproductispermanentlyfixed tothe
wallor other suitable surface.Fixingdevicesarenot
includedsincedierentsurfacematerials require
dierentattachments.Pleaseseekprofessionaladvice
ifyouarein doubtofwhatfixingdevicetouse.
COUNTRYOFORIGIN
CHINA
IMPORTEDBY
FHLDistributionCentrePtyLtd
71SevilleStreet
FAIRFIELDEAST
NSW2165
AUSTRALIA
PO#:ABC123
(H12)
(P2)
(P1)
(P5)
(H12)
Secure 6 x Leg Studs (H12) to Support Panel (P5) and Left & Right Side Panels (P1&P2)
as shown using the Hammer.
(H12)
(H12)
(H12)
(H12)
(H12)
Carefully align the edges of the Back Panel (P6) with the frame of the partially assembled
unit. Secure Back Panel (P6) to Bottom Panel (P4),Top Panel (P3), and Left & Right Side
Panels (P1&P2) with 32 x Nails (H9) as shown using the Hammer. Fix each nail 5mm from