fantastic furniture HAVANA User manual

Version 1.0
HAVANA
Hall Table 2 Drawer
www.fantasticfurniture.com.au

Enjoy
Your purchase from
Australia’s Best Value Furniture Store
www.fantasticfurniture.com.au PAGE 2

Assembly checklist
Useful Information
www.fantasticfurniture.com.au PAGE 3
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.

Top Panel
(P1)
Side
Panel
(P2)
Side
Panel
(P2)
Back Panel
(P11)
24 x Cam
Bolts
(H3)
24 x Cam
Nuts
(H4)
Parts list
Box 1: Top Panel (P1);
2 x Side Panels (P2);
Divider (P3);
Rail (P4); Rail (P5); Rail (P6);
LF Leg (P7); RF Leg (P8);
LR Leg (P9); RR Leg (P10);
Back Panel (P11);
Drawer Front (P12);
Drawer Front (P13);
2 x Left Drawer Sides (P14);
2 x Right Drawer Sides (P15);
2 x Drawer Bases (P16);
2 x Drawer Backs (P17);
www.fantasticfurniture.com.au PAGE 4
20 x Small
Screws
(H5)
Rail
(P5)
Rail
(P4)
8 x Small
Cam Nuts
(H11)
8 x Small
Cam Bolts
(H10)
Left
Drawer Side
(P14)
Right
Drawer Side
(P15)
Drawer Back
(P17)
Drawer
Base
(P16)
Drawer Front
(P12, P13)
2 x CL Runner
Tracks
(H6)
4 x Plastic
Glides
(H16)
4 x Round
Head Bolts
(H14)
2 x CR Runner
Tracks
(H7)
2 x Handles
(H13)
2 x DR
Runners
(H9)
2 x DL
Runners
(H8)
LR
Leg
(P9)
RR Leg
(P10)
RF
Leg
(P8)
LF
Leg
(P7)
LF : Left Front LR : Left Rear
RF : Right Front RR : Right Rear
8 x Long
Screws (L25mm)
(H12)
×2
Hardware pack
Rail
(P6)
Divider
(P3)
What you need
to assemble the product
Additional Tools Required
Flat head screwdriver;
Phillips head screwdriver;
Hammer
DO NOT USE
8 x Dowels
(H1) 20 x Small Dowels
(H2)
4 x Wooden
Screws (L30mm)
(H15)
1 x Safety
Strap
(H17)
2 x Washers
(H19)
1 x Screw
(L25mm)
(H18)

www.fantasticfurniture.com.au PAGE 5
You will need
Step 1
You will need
Step 2
8 x Cam Bolts
(H3) Phillips head screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Insert 3 x Small Dowels (H2) into the hole of LF Leg (P7) as shown.
Insert 2 x Cam Nuts (H4) into the holes of Rail (P4) and Side Panel (P2).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Rail (P4) and Side Panel (P2) to LF Leg (P7), then tighten the cam nut.
(P7)
(P4)
(P2)
(P7)
(P8)
(P9)
(P10)
H4
H4 H2
H2
H2
Insert 8 x Cam Bolts (H3) into the hole of Legs (P7, P8, P9, P10) as shown.
H3 H3
H3
H3
H3
H3 H3
H3
2 x Cam Nuts
(H4)
Flat head
screwdriver
3 x Small
Dowels (H2)

www.fantasticfurniture.com.au PAGE 6
You will need
Step 3
Insert 3 x Small Dowels (H2) into the hole of RR Leg (P10) as shown.
Insert 2 x Cam Nuts (H4) into the holes of Rail (P5) and Side Panel (P2).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Rail (P5) and Side Panel (P2) to RR Leg (P10), then tighten the cam nut.
(P4) (P2)
(P9)
(P10)
(P2)
(P5)
You will need
Step 4
Insert 3 x Small Dowels (H2) into the hole of Rail (P4) and Side Panel (P2).
Insert 2 x Cam Nuts (H4) into the holes of Rail (P4) and Side Panel (P2).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach LR Leg (P9) to Side Panel (P2) and Rail (P4),
then tighten the cam nut
using a Flat head screwdriver.
2 x Cam Nuts
(H4)
Flat head
screwdriver
H4
H4
H2
H2
H2
3 x Small
Dowels (H2)
2 x Cam Nuts
(H4)
Flat head
screwdriver
3 x Small
Dowels (H2)
H4
H4 H2
H2
H2

www.fantasticfurniture.com.au PAGE 7
You will need
Step 6
(P7)
(P8)
(P9)
(P10)
Insert 3 x Small Dowels (H2) into the hole of Rail (P5) and Side Panel (P2).
Insert 2 x Cam Nuts (H4) into the holes of Rail (P5) and Side Panel (P2).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach RF Leg (P8) to Side Panel (P2) and Rail (P5),
then tighten the cam nuts
using a Flat head screwdriver.
You will need
Step 5
(P10)
(P5)
(P5)
(P4)
(P2)
(P8)
H4
H4
H2
H2
H2
Attach 1 x CL Runner Track (H6) to Rail (P4) with 3 x Small Screws (H5).
Attach 1 x CR Runner Track (H7) to Rail (P5) with 3 x Small Screws (H5).
1 x CL Runner
Track (H6)
6 x Small
Screws (H5) Phillips head
screwdriver
1 x CR Runner
Track (H7)
H7
CR
H5
H6
CL
H5
H5
H5
H5
H7
H5 H5
H5 H6
2 x Cam Nuts
(H4)
Flat head
screwdriver
3 x Small
Dowels (H2)

www.fantasticfurniture.com.au PAGE 8
6 x Cam Bolts
(H3) Phillips head screwdriver
You will need
Step 7
(P10)
(P9)
(P8)
(P7)
Insert 6 x Cam Bolts (H3) into the holes of Legs (P9, P10) and Rails (P4, P5) as shown.
You will need
Step 8
1 x CL Runner
Track (H6) 3 x Small
Screws (H5)
Phillips head
screwdriver
H7
CR
H5
H6
CL
H5
Turn Divider (P3) over to the other side.
Attach 1 x CL Runner Track (H6) to Divider (P3) with 3 x Small Screws (H5).
You will need
Step 9
3 x Small
Screws (H5)
Phillips head
screwdriver
1 x CR Runner
Track (H7)
H3
H3 H3 H3
H3
H3
H5
H5 PVC edge
H5
H7
(P3)
(P3)
H5 H5
H6
H5
Attach 1 x CR Runner Track (H7) to Divider (P3) with 3 x Small Screws (H5).
PVC edge
Second hole from
front of runner track

www.fantasticfurniture.com.au PAGE 9
(P11)
(P3)
(P3)
(P6)
Attach Divider (P3) to Back Panel (P11) with 2 x Wooden Screws (H15) using a Phillips head screwdriver.
Attach Rail (P6) to Divider (P3) with 2 x Wooden Screws (H15)
using a Phillips head screwdriver.
You will need
Step 10
Phillips head
screwdriver
You will need
Step 11
Phillips head
screwdriver
H15
H15 H15
2 x Wooden
Screws (H15)
2 x Wooden
Screws (H15)
H15
PVC edge

www.fantasticfurniture.com.au PAGE 10
(P7)
(P8)
(P10)
(P9)
(P11)
(P11)
(P6)
(P6)
H2
Insert 1 x Small Dowel (H2) into LF Leg (P7).
Insert 3
x Cam Nuts (H4) into the holes of Rail (P6) and Back Panel (P11).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach
Rail (P6) and Back Panel (P11) into place.
Tighten the cam nuts using a Flat head screwdriver.
Insert 1 x Small Dowel (H2) into RF Leg (P8).
Insert 3
x Cam Nuts (H4) into the holes of Rail (P6) and Back Panel (P11).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach
the right frame into place,and then tighten the cam nuts.
You will need
Step 12
3 x Cam Nuts
(H4)
Flat head
screwdriver
1 x Small
Dowel (H2)
You will need
Step 13
3 x Cam Nuts
(H4)
Flat head
screwdriver
1 x Small
Dowel (H2)
H2 H4H4 H4
H4H4 H4