fantastic furniture Cove User manual

Version 1.0
Cove
Buet 2 Door
fantasticfurniture.com.au

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 30kgs on top.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Bottom Panel (P2);
Left Side Panel (P3);
Right Side Panel (P4);
Divider (P5);
Divider (P6);
2 x Back Panels (P7);
Back Panel (P8);
Door (P9);
Door (P10);
4 x Legs (P11);
Support Bar (P12);
2 x Shelf Panels (P13)
Hardware pack
Top Panel
(P1)
Bottom Panel
(P2)
Support Bar
(P12)
Legs
(P11)
Left Side
Panel (P3)
Right Side
Panel (P4)
Door
(P10)
Shelf Panel
(P13)
Shelf Panel
(P13)
Divider
(P5)
Divider
(P6)
Back Panel
(P7)
Back Panel
(P7)
Back Panel
(P8)
Door
(P9)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
24 x Dowels
(H1)
8 x Screws
(H2)
32 x Small
Screws
(H5)
4 x Clips
(H6)
16 x Cam Bolts
(H3)
16 x Cam Nuts
(H4)
4 x Wheels
(H7)
4 x Plastic
Glides
(H8)
x4
8 x Wedges
(H9)
8 x Wedge
Screws
(H10)
4 x Bolts
(H11)
2 x Screws
(H14)
2 x Safety
Straps
(H13)
4 x Washers
(H15)
Allen Key
(H12)
20 x Screws
(H16)
4 x Brackets
(H17)

(P1)
(P4)
(P6)
You will need
Step 1
Step 2
You will need
Phillips Head
Screwdriver
Phillips Head
Screwdriver
8 x Cam Bolts
(H3)
Attach 8 x Cam Bolts (H3) to Top Panel (P1) by tightening with the Phillips Head Screwdriver.
Attach 4 x Cam Bolts (H3) to Right Side Panel (P4) and Divider (P6) by
tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 5
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
4 x Cam Bolts
(H3)

You will need
Step 3
Step 4
You will need
Attach 4 x Cam Bolts (H3) to Left Side Panel (P3) and Divider (P5) by
tightening with the Phillips Head Screwdriver.
Insert 4 x Cam Nuts (H4) and 4 x Dowels (H1) into Shelf Panel (P13) as shown.
Rotate the cam nuts so the arrow points towards the incoming cam bolts.
Attach Divider (P5) and Left Side Panel (P3) to Shelf Panel (P13) by tightening
with the Phillips Head Screwdriver.
4 x Cam Nuts
(H4)
Phillips Head
Screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
(P3)
(P3)
(P5)
(P5) (P13)
fantasticfurniture.com.au Page 6
H3
H3
H3
H3
H4
H4
H4
H4
H1
H1
H1
H1
4 x Dowels
(H1)
Phillips Head
Screwdriver
4 x Cam Bolts
(H3)

Insert 4 x Cam Nuts (H4)
and 4 x Dowels (H1) into
Shelf Panel (P13) as shown.
Rotate the cam nuts so the
arrow points towards the incoming
cam bolts. Attach Divider (P6) and Right
Side Panel (P4) to Shelf Panel (P13) by tightening with the Phillips Head Screwdriver.
Insert 8 x Cam Nuts (H4)
into Left & Right Side
Panels (P3 & P4) and
Dividers (P5 & P6). Insert
8 x Dowels (H1) into Top
Panel (P1) as shown.
Rotate the cam nuts so
the arrow points towards
the incoming cam bolts.
Attach Left & Right Side
Panels (P3 & P4) and Dividers (P5 & P6)
to Top Panel (P1) by tightening with the Phillips Head Screwdriver.
Step 5
You will need
4 x Cam Nuts
(H4)
Phillips Head
Screwdriver (P4)
(P6)
(P6)
(P4)
(P5)
(P13)
(P3)
(P1)
fantasticfurniture.com.au Page 7
H4
H4
H4
H4
H4
H4
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
4 x Dowels
(H1)
Step 6
You will need
8 x Cam Nuts
(H4)
Phillips Head
Screwdriver
8 x Dowels
(H1)

Phillips Head
Screwdriver
Step 7
Slide Back Panels (P7 x 2, P8) into the grooves of Left & Right Side Panel (P3 & P4).
Attach 8 x Dowels (H1)
into the Left & Right Side Panels (P3 & P4) and Dividers (P5 & P6). With assistance,
carefully align the bottom panel (P2) to the assembled frame as shown. Ensure the
Back Panels (P7 x 2, P8) slot into the grooves on the Bottom Panel (P2). Secure
together using 8 x Screws (H2) tightening with a Phillips Head Screwdriver.
You will need
Step 8
(P6)
(P4)
(P5)
(P3)
(P7)
(P8)
(P7)
(P2)
(P4)
(P6)
(P5)
(P3)
fantasticfurniture.com.au Page 8
H1
H1
H1
H1
H2
H2
H2
H2
H2
H2
H2
H2
H1
8 x Dowels
(H1)
8 x Screws
(H2)
Required
Two People

You will need
Step 10
Phillips Head
Screwdriver
You will need
Step 9
Attach Support Bar (P12) to Bottom Panel (P2) with 4 xBolts (H11) by tightening
with an Allen Key (H12). With assistance, carefully turn the assembled unit upright.
(P2)
(P2)
fantasticfurniture.com.au Page 9
H16
H17
H17
H17
H17
H16
H16
H16
H12
H11
H11
H11
H11
4 x Bolts
(H11)
Allen Key
(H12)
H11
4 x Brackets
(H17)
20 x Screws
(H16)
Attach 4 x Brackets (H17) to Bottom Panel (P2) with 20 x Screws (H16) as shown.
Tighten with a Phillips Head Screwdriver.
H16 H16
H17
(P12)
Required
Two People

You will need
Step 11
(P9)
(P10)
(P11)
(P11)
(P11)
(P11)
fantasticfurniture.com.au Page 10
Turn 4 x Legs (P11) clockwise into the brackets until secure. Hammer 4 x Plastic Glides (H8) on
Legs (P11 x 4) as shown.
You will need
Step 12
H8
H8
H8
H8
Phillips Head
Screwdriver
4 x Plastic
Glides (H8) Hammer
H5
32 x Small
Screws(H5)
4 x Clips
(H6)
4 x Wheels
(H7)
H7
H5
Attach 4 x Clips (H6) and 4 x Wheels (H7) to Doors (P9 & P10) with
32 x Small Screws (H5). Tighten with a Phillips Head Screwdriver.
H7
H6
H6
H6
H5
H5
H5
H5
H5
H6
H5
H6
H5
H7
H5
H7
H5 H7
H5