fantastic furniture Bridge Tallboy User manual

Bridge
Tallboy 3 Drawer Oak

r

Hardware Pack
Top Panel (P1)
Bottom Panel (P2)
Right Panel (P3)
Left Panel (P4)
2 x Back Panels (P5)
3 x Support Panels (P6)
Back Support Panel (P7)
3 x Drawer Backs (P9)
Drawer Left Panels (P10)
Drawer Right Panels (P11)
Drawer Bottoms (P12)
3 x Drawer Supports(P13)
2 x Legs(P14)
3 x Drawer Doors (P8)
3 x
3 x
3 x
3 x Left Runner
Track
(H9-1)
12 x Long Screws
(H10)
36 x Cam Bolts
(H1)
36 x Cam Nuts
(H2)
18 x Dowels
(H3)
12 x Small Washers
(H4)
12 x Bolts
(H5)
1 x Allen Key
(H7)
4 x Levelling Feet
(H8)
36 x Short Screws
(H6)
3 x Right Runner
Track
(H -2)9
3 x Left
Runner
(H -3)9
3 x Right
Runner
(H -4)9
TopPanel
(P1)
Bottom Panel
(P2)
Right Panel
(P3)
Back Panel
(P5)
Support (P6)
Panel
Back Support Panel(P7)
Drawer Door
(P8)
Drawer Bottom
(P12)
Drawer Support
(P13)
Left Panel
(P4)
Back Panel
(P5)
Support Panel (P6)
Support (P6)Panel
Drawer Back
(P9)
Draw er L eft Panel
(P10 )
Draw er R ight Panel
(P11 )
Leg
(P14)
Leg
(P14)
12 x Wedges
(H11)
4 x Washers
(H12)
2 x Wall Straps
(H13)
2 x Medium Screws
(H14)

H8
P14
H7
H5
H4
H3
H1
H3H1
H1 H3
H1
H3
12 x Small Washers
(H4)
12 x Bolts
(H5)
1 x Allen Key
(H7)
4 x Levelling Feet
(H8)
Using 12 x bolts (H5) and 12 x small washers (H4), secure the 2 x legs (P14) to
the bottom panel (P2), tightening completely with allen key (H7).
Screw in 4 x levelling feet (H8) into the bottom of the 2 x legs (P14) as shown.
Ensure they are secure.
P2
H3
H1
H3H1
H1 H3
H1
H3
P2
P1
8 x Cam Bolts
(H1)
8 x Dowels
(H3)
Phillips Head
Screwdriver
With assistance, carefully turn the bottom panel upright.
Insert 4 x dowels (H3) into the bottom panel (P2). Secure 4 x cam bolts (H1) into
the bottom panel, tightening with a phillips head srewdriver.
Repeat this step for the top panel (P1).

4
P4
P3
H1 H1
H3 H1
H3 H1
H3
H1
P3
P4
P7 P6
P6
P6
10 x Cam Bolts
(H1)
6x Dowels
(H3)
Phillips Head
Screwdriver
Insert 3 x dowels (H3) into the right panel (P3). Secure 5 x cam bolts (H1) to
the right panel (P3), tightening using a phillips head screwdriver.
Repeat this step for the left panel (P4).
Align and attach the 3 x support panels (P6) and the back support panel (P7) to
the right panel (P3). With assistance, align and attach the left side panel (P4) to
the 3 x support panels (P6) and back support panel (P7) as shown.

Page 7
5
6
H2
H2
10 x Cam Nuts
(H2)
Insert 10 x cam nuts (H2) into the 4 x support panels (P6, P7), rotating
the cam nuts so the arrow points towards the incoming cam bolt.
Secure the panels together by tightening the cam nuts (H2) using a phillips
head screwdriver.
Phillips Head
Screwdriver
With assistance, attach the assembled frame onto the bottom panel (P2) as shown.
Ensure the grooves on the bottom, left and right panels (P2, P3, P4) align.
Insert 4 x cam nuts (H2) into the bottom of the left and right panels (P3, P4), rotating
the cam nuts so the arrow points towards the incoming cam bolts.
Secure the panels together by tightening the cam nuts (H2) using
a phillips head screwdriver.
(H2)
(H2)
(H2)
4 x Cam Nuts
(H2)
Phillips Head
Screwdriver

Page 8
7
8
P5
Note: ensure the back panel (P5) slots all the
way into the groove on the bottom panel (P2).
Slide the 2 x back panels (P5) into the grooves of the bottom,
left and right panels (P2, P3, P4) as shown.
P1
Insert 4 x cam nuts (H2) into the top of the left and right panels (P3, P4), rotating the cam nuts so
the arrows point towards the incoming cam bolts.
With assistance, carefully align and lower the top panel (P1) onto the assembled
unit as shown.
Secure the panels together by tightening the cam bolts (H2) on the left and
right panels (P3, P4) using a phillips head screwdriver.
4 x Cam Nuts
(H2)
Phillips Head
Screwdriver
Note: ensure the back panel (P5) slots
into the groove on the top panel (P1).

Page 9
9
10
Secure 6 x cam bolts (H1) to 1 x drawer door (P8), tightening using
a phillips head screwdriver.
Repeat this step for the other 2 x drawer doors (P8).
18 x Cam Bolts
(H1) Phillips Head
Screwdriver
(P8)
(H1)
X3
(H1)
(H1)
(H1)
(P10)
(P11)
X3
(P8)
Align and attach 1 x drawer support (P13), 1 x drawer left panel (P10) and 1 x drawer
right panel (P11) to 1 x drawer door (P8). Ensure the grooves on the
drawer panels (P8, P10, P11) align as shown.
Insert 6 x cam nuts (H2) into the panels (P10, P11, P13), rotating the cam
nuts so the arrow points towards incoming cam bolts. Secure the panels by
tightening the cam nuts (H2) using a phillips head screwdriver.
Repeat this step for the other 2 x drawers.
18
(P13)

Page 10
11
12
(P10)
(P11)
(P12)
X3
(P8)
Slide 1 x drawer bottom (P12) into the grooves on the panels (P8, P10, P11) as shown.
Repeat this step for the other 2 x drawers.
Align 1 x drawer back (P9) to the assembled drawer. Ensure the pre-drilled holes on the
left and right drawer panels (P10, P11) and drawer support (P13)
align with the pre-drilled holes on the drawer back (P9).
Secure together using 6 x long screws (H10), completely tightening with
a phillips head screwdriver.
Repeat this step for the other 2 x drawers.
(P9)
18 x Long Screw
(H10)
X3
(H10)
(H10)
(H10)
(H10)
(H10)