fantastic furniture TATE User manual

Version 1.0
www.fantasticfurniture.com.au
Recliner + Foot Stool
TATE

www.fantasticfurniture.com.au PAGE 2www.fantasticfurniture.com.au PAGE 2
Enjoy
Your purchase from
Australia’s Best Value Furniture Store
CAUTION:
Use this product for seating one person at a time.
Do not stand on, or use this chair as a step ladder.
Do not rock on chair as this may result in injury.
This product should be checked periodically to ensure
alle components are secure and all hardware is tight.
RECOMMENDED WEIGHT CAPACITY 120 KG

www.fantasticfurniture.com.au PAGE 3
Assembly checklist
Read through the instructions carefully
before you begin.
Make sure you have all the required tools.
Never use power tools unless instructed.
Identify and lay out all of the components
before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
Useful Information
! Never use power tools unless specically instructed. They can damage your components or
hardware if used incorrectly
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not t through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! If you are having any di󰀩culties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.

www.fantasticfurniture.com.au PAGE 4
What you need
to assemble the product
Parts list
Box 1: Seat/Back (P1); Armrests (P2);
Chair leg (P3); Footstool cushion (P4);
Footstool leg (P5).
18 x Bolts
(H1)
8 x Small bolts
(H2)
2 x Lock
(H3)
2 x Clips
(H4)
18 x Washers
(H5)
1 x Leg mount for chair
(H6)
4 x Bracket
(H7)
1 x Leg mount for footstool
(H8)
1 x Allen key
(H9)
Seat/Back
1 x (P1)
Armrests
(P2L), (P2R)
Chair leg
5 x (P3)
Footstool cushion
1 x (P4)
Footstool leg
4 x (P5)
(P2L) (P2R)

www.fantasticfurniture.com.au PAGE 5
.
Step 1
Step 2
You will need
10 x H1 10 x H5
1 x H6 1 x H9
Place seat/back (P1) on top of base.
Attach 5xP3 (chair leg) to H6 (Leg mount for chair)
by using 10 x bolt H1, 10 x washer H5 and Allen key H9
tighten each bolt H1to 80% at beginning, when all legs are level
and flat on the floor, tighten all bolts H1 to 100%
P1
P3
H1 H5
H6
P3
P3
P3
P3
x5

www.fantasticfurniture.com.au PAGE 6
.
Step 3
Step 4
You will need
2 x H3 2 x H4
Attach armrests (P2) to seat using
small bolts (H2) and allen key (H9).
You will need
4 x H2 1 x H9
Using 1 x lock pin (H3) to connect the back to the seat base then lock the pin (H3)
into position with 1 x clip (H4). Repeat this for both sides.
P2R
P2L
H2
H2
H2
H2
H9

www.fantasticfurniture.com.au PAGE 7
Step 5
Step 6
Use 2 x Bolts (H1) to connect 1 x Bracket (H7) to the footstool leg (P5) as shown.
Only turn Bolts (H1) to loosely connect to the Brackets (H7) through the holes on
(P5). Repeat this for all wooden legs (P8).
Slide the wooden base (P5) into position onto the leg mount (H8). When (P5) is into
position and level, fully tighten all Bolts (H1) by hand.
H2
You will need
4 x H2 1 x H9
Attach footstool cushion (P4) to leg mount for footstool (H8)
by using 4 x small bolts (H2) and allen key (H9).
H2
H8
H2
H2
P4
H7
P5
Bolts
Brackets
(H7)
8 x
Washer
(H5)
(H9)
H5
H8

www.fantasticfurniture.com.au PAGE 8
Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
.
Step 7