fantastic furniture Giselle User manual

Giselle
Day Bed
fantasticfurniture.com.au
Version 1.0
.
.

We’re thrilled you’ve chosen Fantastic Furniture
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
fantasticfurniture.com.au Page 2
to help create a home you’ll love!
Look like you’ve found
your Fantastic!

Read through the instructions carefully
before you begin.
Make sure you have all the required tools.
Never use power tools unless instructed.
Identify and lay out all of the components
before you begin assembly.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
! Never use power tools unless specifically instructed.They can damage your components or
hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
!
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
fantasticfurniture.com.au Page 3
Useful information
Assembly checklist

Part List:
Box 1:
Back Panel (P1);
Left Panel (P2);
Right Panel(P3);
Cross Bar(P5)
26 x Plastic Slat Caps (P6);
Box 2:
2 x Side Rails (P4);
13 x Slats (P7)
Hardware pack
8 x Short Bolts
(H1)
Page 4
1 x Allen Key
(H3)
13 x Slats
(P7)
26 x Plastic
Slat Caps
(P6)
What you need
Please make sure you have all these parts before you start.
fantasticfurniture.com.au
4 x Long Bolts
(H2)
1 x Back Panel (P1)
1 x Left Panel (P2)
1 x Right Panel (P3)
2 x Side Rails (P4)
1x Cross Bar(P5)
2 x Medium Bolts
(H4)
2 x Hex Nuts
(H5)
1x Spanner
(H6)
.
.
to assemble the product

Step 1
You will need
4 x Short Bolts
(H1)
1 x Allen Key
(H3)
Insert 4 x short bolts (H1) into the bottom holes of the left panel (P2) and right panel (P3) using
the allen key (H3). Do not fully tighten the bolts and leave a gap of 5mm as shown.
Step 2
(P2) (P3)
Page 5
fantasticfurniture.com.au
(H1)
5mm
1.
2.
(H1)
(P4)
(P4)
(P5)
You will need
4 x Short Bolts
(H1)
2 x
Medium Bolts
(H4)
1 x Allen Key
(H3)
2 xHex Nuts
(H5)
1 x Spanner
(H6)
(H4)
(H3)
(H5)
(H6)
.
(P3)
(P2)
.
.
Attach the 2 x side rails (P4) to the left panel (P2) and right panel (P3).
Slot the side rails onto the bolts on the left and right panels (P2 & P3) as shown.
Then insert 4 x short bolts (H1) into the top holes with the allen key (H3).
Attach cross bar (P5) onto 2 x side rails (P4) using 2 x medium bolts (H4) and 2 x hex
nuts (H4).
Tighten with the allen key (H3) and spanner (H6) as shown.

Step 3
You will need
4 x Long Bolts
(H2)
1 x Allen Key
(H3)
fantasticfurniture.com.au
Step 4
Page 6
You will need:
26 x Plastic
Slat Caps
(P6)
Push 26 x plastic slat caps (P6) firmly onto 13 x slats (P6).
13 x Flat LVL Slats
(P7)
(P7)
(P6) (P6)
(P1)
(P2)
(P3)
(H2)
.
Attach the back panel (P1) to the left and right panel (P2 & P3 ) with 4 x long bolts (H2) using
an allen key (H3). Now fully tighten all bolts.

Lower the slat (P7) with the end caps (P6) to the side rails (P4). Ensure the plastic
caps are in place over the side rail holes and apply downward pressure until the
plastic caps are fully inserted into the rails. Repeat for every bed slat until finished.
Step 5
IMPORTANT: Fully tighten all bolts on bed. Periodically check to ensure all bolts remain tight.
In the interest of our environment please dispose of all packaging thoughtfully.
Step 6
Job Complete!
fantasticfurniture.com.au Page 7
.
.
.
.