fantastic furniture HOME ROBE User manual

Assembly Instructions
HOME ROBE
3 Door 1800mm

It is recommended the wardrobe is assembled in the
room that it is intended for.
(CLEAR FLOOR SPACE IN ROOM IF REQUIRED)

1
1
3
4
5
6
7
9
3 x Hanging Rails
6
8
8
Page 3
28 x CONFIRMAT SCREWS 20 X CONFIRMAT SCREW CAPS
3 x BAGS OF NAILS
6 x Hanging Rail Brackets 6 x 1/2 6g C/S SCREWS
2 x Wall Fixing Brackets
8 x 5/8 PAN HEAD SCREWS
2 x T Z FITTING
2 x 28MM NIB SCREW
2
2
2
Hammer
.
.
.
.

STEP 1
1 1
3
4
7
9
Page 4
1. INSERT TZ FITTINGS INTO PARTS 1 IN HOLES PROVIDED, AS
SHOWN
2. INSERT THE PANELS ONTO PART 4 AS SHOWN IN PICTURE
Towards top edge
TZ Fitting
Knock into Parts 1
.
.
.
.

6
1
1
3
4
7
9
STEP 2
INSERT THE PANELS 6 & 8 BETWEEN PARTS 3, 7 & 9 AS SHOWN
IN PICTURE.
NOTE: BEFORE FIXING DIVISION (8) TO PANELS 7 & 9 INSERT 2
CONFIRMAT SCREWS THROUGH PART 7 INTO PART 6
CONFIRMAT SCREWS THROUGH
PART 7 USING THE HOLES PROVIDED
INTO PARTS 6
8
8
6
Page 5
MAKE SURE THE
EDGED SIDE OF 8 IS
FACING THE FRONT
.
.
.
.

STEP 3
1
1
3
7
9
5
1. INSERT THE GABLE (5) INTO THE GUIDE HOLES OF PANEL 3, 7 & 9 TO
COMPLETE THE MAIN CARCASS.
INSERT ALL CONFIRMAT SCREWS AND CAPS INTO THE CARCASS USING
THE HOLES PROVIDED.
NOTE: THE CONFIRMAT SCREWS USED ON THE BOTTOM AND THE TOP
OF THE UNIT DO NOT NEED CAPS.
2. FIX PARTS 1 TO PART 3 BY SCREWING THE PARTS TOGETHER
THROUGH THE TZ FITTING USING THE 28mm NIB SCREW
CONFIRMAT SCREW
CONFIRMAT SCREW & CAP
6
4
6
8
8
Page 6
28MM NIB
SCREW
THROUGH TZ
FITTING INTO
PART 3
.
.
.
.
.
.
.
.
.
.
.
.
.
.

STEP 4
..........
9 5
............
..........
............
..........
..........
........ . ..
.... ..... . ..
Page 7
2
2
2
MAKE SURE THE UNIT IS “SQUARE”WHEN NAILING BACK PANELS
USING THE BAGS OF NAILS, NAIL ON THE BACK PANELS TO THE MAIN
CARCASS,
MAKING SURE TO NAIL CLOSE TO THE EDGES SO THE NAIL GOES
INTO THE PARTICLE BOARD BEHIND IT.

STEP 5
In the interest of our environment
Please dispose of all packaging thoughtfully.
YOUR CARCASS IS NOW COMPLETE
USING THE GUIDE HOLES PROVIDED IN PANELS 4,5 & 6 INSERT THE
HANGING RAIL BRACKETS AND SCREW IN BRACKETS WITH 1/2 6g C/S
SCREWS AT THE TOP OF THE UNIT AND IN TURN INSERT THE HANGING
RAIL INTO THESE BRACKETS
Page 8
4
5
6
6
.
.
.
.

8 x 5/8 PAN HEAD
SCREWS
DOOR ASSEMBLY
x3
TOP TRACK
BOTTOM TRACK
Page 9
Philips Head Screwdriver
(Not Supplied)
SLIDING DOOR

USING THE 5/8 PAN HEAD SCREWS PROVIDED, SCREW IN THE
TOPAND BOTTOM TRACK, USING THE HOLES PROVIDED IN
THE TRACK.
MAKE SURE THAT THE FRONT EDGE OF THE WARDROBE AND
THE FRONT EDGE OF THE TRACK LINE UP (AS SHOWN).
STEP 6
TOP TRACK
BOTTOM TRACK
BASE PANEL
FRONT
Page 10