fantastic furniture Bravo King Bed User manual

Version 1.0
Bravo
fantasticfurniture.com.au
Queen/King Bed

fantasticfurniture.com.au Page 2Page 2
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!

Assembly checklist
Useful information
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Please see page 2 for any safety requirements or weight restrictions.
Page 3
fantasticfurniture.com.au

/
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
fantasticfurniture.com.au Page 4
Headboard
(P1)
Side Rail (P5)
Side Rail (P5) Footboard
(P2)
Headboard Footboard
Leg (P3)
Timber Cross Rail
(P10)
Headboard Footboard
Leg (P3)
Centre Rail
(P6)
Support Leg (P4)
Support Leg (P4)
28 x End Connectors (P7) 14 x Centre Connectors (P8)
28 x Slats (P9)
Parts list
Box 1 :
Headboard (P1) ; Slats (P9)
Box 2 :
/
Hardware pack
Footboard (P2) ; Headboard Footboard Leg (P3) ; 2 x Support Legs (P4) ;
2 x Side Rails (P5) ; Center Rail (P6) ; End Connectors (P7) ; Centre Connectors (P8) ;
Timber Cross Rail (P10) ; Hardware Pack.
8 x Short Bolts
(H1)
1 x Allen Key
(H2)
8 x Large Screws
(H3)
2 x Small Screws
(H6)
6 x Long Bolts
(H4)
6 x Washers
(H5)
1 x Felt Pad
(H7)
/

Step 1
(P2)
(P1)
(P3)
(H3)
Attach legs (P3) to the bottom of headboard (P1) and footboard (P2)
with 8 x large screws (H3).
Step 2
You will need
(H1) (H2)
Allen Key
(P1)
(P2)
(P5)
(H1)
(H2)
fantasticfurniture.com.au Page 5
You will need
8 x Large Screws
(H3)
Phillips head
Screwdriver
(not provided)
8 x Short Bolts
Install the 8 x short bolts (H1) to the brackets of the headboard (P1) and footboard (P2) by using
side rails (P5) to headboard (P1) and footboard (P2) by slotting the bracket on the side rails (P5)
over the bolt as shown. No need to tighten bolts until step 6.
the allen key (H2) as shown, do not tighten the bolts and keep them 8mm loose. Then attach

Step 3
(H5)
(H4)
(P6)
(P4)
Attach the support legs (P4) to the centre rail (P6) using 2 x long bolts (H4), 2 x washers (H5)
Step 4
(H5) (H4)
(P6)
(P6)
(P1)
(P2)
(P5)
Adjust to be 10mm gap from floor
to the bottom of support legs.
fantasticfurniture.com.au Page 6
as shown.
You will need
(H5)
(H4)
Phillips head
Screwdriver
(not provided)
You will need
(H5)
(H4)
Phillips head
Screwdriver
(not provided)
2 x Washers
2 x Long Bolts
4 x Washers
4 x Long Bolts
Slot the centre rail (P6) into the headboard (P1) and footboard (P2).
Insert and attach the long bolts (H4) using a phillips head screwdriver (not provided) to the
headboard (P1) and footboard (P2). No need to tighten bolts until step 6.

Step 5
You will need
28 x End
Connectors
(P7)
14 x Centre
Connectors
(P8)
28 x Slats
(P9)
(P7) (P7)
(P8)
(P9) (P9)
fantasticfurniture.com.au Page 7
Sometimes it makes it easier to line up the
hole if you press down in the middle of the
slat to flatten it out.
1
2
3
Attach 2 x end connectors (P7), 1 x centre connector (P8)
and 2 x slats (P9) together as shown. Repeat this for the remaining slats.
Lower the completed slat (P7), (P9) and (P8) into side rails (P5). Ensure the connectors are in
place over the side rail holes and apply downward pressure on the slat (P9) with
the end connectors (P7) until the end plastic cap is fully inserted into the rail.

Repeat for every bed slat until finished.
fantasticfurniture.com.au Page 8
Step 6
(H7)
(P1)
(P2)
(P5)
(P10)
(H7)
(P6)
(P10)
(H6)
(H2)
4
You will need
2 x Small Screws
(H6)
(H2)
Allen Key
Phillips head
Screwdriver
(not provided)
1 x Felt pad
Make sure that the bed is square
Attach the timber cross rail (P10) to the centre of side rails (P5) by using 2 x small screws (H6).
Then attach the felt pad (H7) to the centre of centre rail (P6) under the cross rail. Now tighten
all the bolts on the centre rail (P6), headboard (P1) and footboard (P2).
Make sure the small
tightened.
screws are fully

Step 7
Job complete!
In the interest of our environment please dispose
of all packaging thoughtfully.
fantasticfurniture.com.au Page 9