fantastic furniture Willow MK2 User manual

Willow MK2
Bed Queen
fantasticfurniture.com.au
Version 1.0

We’re thrilled you’ve chosen Fantastic Furniture
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
fantasticfurniture.com.au Page 2
to help create a home you’ll love!
Look like you’ve found
your Fantastic!

Read through the instructions carefully
before you begin.
Make sure you have all the required tools.
Never use power tools unless instructed.
Identify and lay out all of the components
before you begin assembly.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
! Never use power tools unless specifically instructed.They can damage your components or
hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
!
components please visit our website Help
Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
fantasticfurniture.com.au Page 3
Assembly checklist
Useful information

Page 4
30 x Slats
(P10)
30 x Plastic Slat Caps
(P8)
What you need
to assemble the product
Please make sure you have all these parts before you start.
1 x Headboard (P1)
1 x Footboard (P2)
fantasticfurniture.com.au
12 x Short Bolts
(H1)
M6x20
4 x Long Bolts
(H2)
M6x60
6 x Medium Bolts
(H6)
M6x40
1 x Allen Key
(H3)
13 x Hex Nuts
(H4)
1 x Spanner
(H5)
3 x Larger Medium Bolts
(H8)
M6x45
2 x Side Rails (P3)
3 x
Support Leg (P5)
1x Cross Bar (P7)
2x Cross Bar (P4)
1 x
Centre Rail (P6)
15 x Centre Plastic
Slat Caps
(P9)
Part List:
Box 1:
Headboard (P1);
Footboard (P2);
3 x Support Legs (P5) ;
30 x Plastic Slat Caps (P8);
15 x Centre
Plastic slat Caps (P9).
Box 2:
2 x Side Rails (P3);
2 x Cross Bars (P4) ;
1 x Centre Rail (P6) ;
1 x Cross Bar (P7) ;
30 x Slats (P10) .
Hardware pack
12x Metal washers
(H7)

Step 2
Page 5
Step 1
You will need
4 x Short Bolts
(H1)
1 x Allen Key
(H3)
(P2)
(P4)
(P4)
(P3)
(P3)
(P7)
(P1)
(H1)
5mm
1.
2.
(H1)
(H3)
Insert 4 x short bolts (H1) into the bottom holes of the headboard (P1) and footboard (P2) using
the allen key (H3). Do not fully tighten the bolts and leave a gap of 5mm as shown.
Attach the 2 x side rails (P3) to the headboard (P1) and footboard (P2).
Slot the side rails onto the bolts as shown and insert 4 x short bolts (H1) into the top holes
with the allen key (H3).
Attach the 2 x cross bars (P4 ) onto the 2 x side rails (P3) using 4 x long bolts (H2) and
4 x hex nuts (H4). Ensure the holes on the centre of the 2 x cross bars (P4) faces downwards.
Attach the cross bar (P7 ) onto the 2 x side rails (P3) using 2 x Larger Medium bolts
(H8) and 2 x hex nuts (H4). Ensure the holes on the centre of the cross bar (P7) faces
upwards.
Tighten with the allen key (H3) and spanner (H5) as shown. Now fully tighten all bolts.
(H2)
(H3)
(H4)
(H5)
You will need
4 x Short Bolts
(H1)
M6x20
4 x Long Bolts
(H2)
M6x60
1 x Allen Key
(H3)
6 x Hex Nuts
(H4)
fantasticfurniture.com.au
2 x Larger Medium
Bolts
(H8)
M6x45
1 x Spanner
(H5)
(H8)
(H3)
(H4)
(H5)

Page 6
Step 3
You will need
1 x Allen Key
(H3)
Step 4
Secure the centre rail (P6) to the 2 x cross bars (P4) with 4 x short bolts (H1), tighten with the
allen key (H3).
Secure the centre rail (P6) to the cross bar (P7) with 1 x Larger Medium Bolts (H8) and 1 x hex
nut (H4), tighten with the allen key (H3) and spanner (H5) as shown.
fantasticfurniture.com.au
Attach the 3 x support legs (P5) to the centre rail (P6) with 6 x medium bolts (H6)
12 x metal washers and 6 x hex nuts (H4).
Tighten with the allen key (H3) and spanner (H5) as shown.
Extend the adjusters on the 3 x support legs (P5) by turning clockwise so that they
are level on the ground.
Important Note: The adjusters must be retracted by turning anticlockwise before
moving the bed.The adjusters should be extended again after moving the bed.
H1
H1
H3
(P4)
(P6)
(P4)
(P6)
(P7)
(P4)
(P5)
H3 H6H7
H5
H4
H7
You will need
6 x Hex Nuts
(H4)
12 x Metal
Washer
( H7 )
1 x Small
Allen Key
( H3 )
1 x
Spanner
( H5 )
(P6)
(P5) (P5)
(P6)
(P5)
H8
H3
(P6)
(P7)
4 x Short Bolts
(H1)
M6x20
H4H5
1 x Hex Nuts
(H4)
1 x Spanner
( H5 )
6 x Medium Bolts
(H6)
M6x40
1 x Larger Medium
Bolt
(H8)
M6x45

Attach 2 x plastic caps (P8), 2 slats (P10) and 1 x centre plastic slat cap (P9) together as shown.
Repeat for the other slats (P10).
Step 6
Page 7fantasticfurniture.com.au
Step 5
Lower the slat (P10) with the end connectors (P8) to the side rails (P3). Ensure the plastic
slat caps are in place over the side rail holes and apply downward pressure until the
plastic slat caps are fully inserted into the rails. Repeat for every bed slat until finished.
Lower the slat (P10) with the plastic slat caps (P8) and centre plastic slat caps (P9) onto the 2 x
side rails (P3) and centre rail (P6). Ensure the plastic slat caps (P8, P9) are in place over the side
rail (P3) holes and centre rail holes (P6) and apply dowward pressure until the plastic slat caps
are fully inserted into the rails. Repeat for every bed slat until finished.
You will need:
30 x Plastic Slat Caps
(P8)
30 x Slats
(P10)
15 x Centre Plastic
Slat Caps
(P9)
(P8)
(P8)
(P9)
(P10)
(P10)

IMPORTANT: Fully tighten all bolts on bed. Periodically check to ensure all bolts remain tight.
In the interest of our environment please dispose of all packaging thoughtfully.
Step 7
Job Complete!
fantasticfurniture.com.au Page 8