fantastic furniture COMO TALLBOY 6 DRW User manual

Assembly Instructions
TALLBOY 6 DRW
COMO

Page 2
2
3
56
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
W
A
R
N
N
G
WARNING
Check no parts are missing.
4
fully tighten screws (leave slightly
loose).When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

Page 3
What You Need
To Assemble The Body
Top Panel
(P1) Right Side
Panel
(P3)
Left
Drawer
Side(P15)
Left Drawer
Side
(P15)
Drawer Front
(P19)
Drawer Front
(P13,P14)
×2
×4
Right Drawer
Side(P16)
Right Drawer
Side
(P16)
Drawer Back
(P21)
Drawer Back
(P18)
Drawer
Base(P20)
Drawer Base
(P17)
Support
Rail
(P22)
Left Side
Panel
(P2)
Rail
(P5)
Rail
(P5)
Rail
(P5)
Rail
(P6)
Rail
(P7)
Rail
(P8)
Rail
(P9)
Rail
(P10)
Divider
(P4)
Connect Stick
(P12)
2 x Back
Panels
(P11)
(Tools not provided)
Flat BladeScrewdriver
Phillips Head Screwdriver
Mallet
34 x Dowels
(H1)
33 x Long
Screws
(H2)
82 x Small
Screws
(H5)
6 x CL Runner
Tracks
(H6)
17 x Cam Bolts
(H3)
17 x Cam Nuts
(H4)
28 x Small
Cam Nuts
(H11)
6 x CR Runner
Tracks
(H7)
6 x DL Runners
(H8)
6 x DR Runners
(H9)
28 x Small
Cam Bolts
(H10)
Please make sure you have all these parts before you start.
1 x Screw
(H13)
1 x Safety Strap
(H12)
2 x Washers
(H14)
4 x Plastic
Glides
(H15)
1x Safety Strap Set

H5
H3
H3
H3
H5
H7
H5
Page 4
Step 1
You will need:
H5
H5 H5
H6
H5
H5 H5
H6
H5
H5 H5
H6
H5
H5
H5
H6
H5
H5 H5
H6
Step 2
You will need:
Step 3
You will need:
H5
H5
H7
H5 H5
H5
H7
H5 H5
H5
H7
H5 H5
H5
H7
H5
5 x CL Runner
Tracks
(H6)
5 x CR Runner
Tracks
(H7)
11 x
Dowels
(H1)
10 x
Cam Bolts
(H3)
15 x Small
Screws
(H5)
15 x Small
Screws
(H5)
(P2)
(P3)
(P3)
(P2)
Attach 5 x CL Runner Tracks (H6) to Left Side Panel (P2) with 15 x Small Screws (H5).
Attach 5 x CR Runner Tracks (H7) to Right Side Panel (P3) with 15 x Small Screws (H5).
Insert 11 x Dowels (H1) into Left Side Panels (P2).
Attach 10 x Cam Bolts (H3) into Side Panels (P2) and (P3) as shown.
H1
H1
H1
H1
H1
H1 H1
H1 H1
H3
H3
H3
H1
H1
H3
H3
H3
H3
H6
CL
H5
H7
CR
H5

H3
H4
H5
H5
H5
H5
H5
H5
H6
H7
Page 5
1 x Cam Bolt
(H3)
Step 4
You will need:
1 x CL Runner
Track
(H6)
3 x Small
Screws
(H5)
(P4)
(P4)
(P4)
(P6)
(P9)
Attach 1 x CL Runner Track (H6) to Divider (P4) with 3 x Small Screws (H5).
Turn Divider (P4) over to the other side,then attach 1 x CR Runner Track (H7)
with 3 x Small Screws (H5).
Attach 1 x Cam Bolt (H3) into Rail (P6).
Insert 1 x Cam Nut (H4) into the hole of Divider (P4).
Rotate the cam nut so the arrow point towards the incoming cam bolt.
Push Divider (P4) into place and tighten the cam nut.
Attach Rail (P9) to Divider (P4) with 1 x Long Screw (H2).
H2
Step 5
You will need:
1 x CR Runner
Track
(H7)
3 x Small
Screws
(H5)
Step 6
You will need:
1 x Long Screw
(H2)
1 x Cam Nut
(H4)
H6
CL
H5
H7
CR
H5
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.

Page 6
Step 7
You will need:
Step 8
5 x Cam Nuts
(H4)
(P9)
(P9)
(P10)
(P8)
(P10)
(P5)
(P5)
(P5)
(P5)
(P5)
(P5)
(P6)
(P6)
(P7)
(P7)
(P8)
(P2)
(P3)
Insert 5 x Cam Nuts (H4) into the holes of Rails (P6) and
(P7,P8,P9,P10).
Rotate the cam nuts so the arrows point
towards the incoming cam bolts.Attach 3 x Rails (P5) and
Rails (P6,P7,P8,P9,P10) to Left Side Panel (P2), then tighten the cam nuts.
Insert 11 x Dowels (H1) into 3 x Rails (P5) and Rails (P6,P7,P8,P9,P10).
Insert 5 x Cam Nuts (H4) into the holes of Rails (P6) and (P7,P8,P9,P10).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Right Side Panel (P3) into place and tighten the cam nuts.
You will need:
5 x Cam Nuts
(H4)
(P2)
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
H4
H4
H4
H4
H4
H4
H4
11 x Dowels
(H1)
H1
H1
H1 H1
H1 H1
H1 H1
H1

Page 7
H15
H15
H15
H15
Step 10
You will need:
4 x Plastic Glides
(H15)
Hammer 4 x Plastic Glides (H15) on Side Panels (P2) and (P3).
(P2)
(P3)
H5
Step 9
You will need:
22 x Small
Screws
(H5)
(P11)
(P11)
(P12)
Join 2 x Back Panels (P11) with Connect Stick (P12),then put
into the groove on the back of the chest,screw it with 22 x Small Screws (H5).
H15
20mm
H5

8 x Dowels
(H1)
(P1)
(P1)
(P2)
(P3)
(P4)
Attach 6 x Cam Bolts (H3) into Top Panel (P1) as shown.
You will need:
6 x Cam Bolts
(H3)
H3
H3
H3
H3
H3
H3
H1
H1
H1
Page 8
Step 11
Step 12
You will need:
Insert 8 x Dowels (H1) into the holes of Side Panels (P2,P3), Divider (P4) and Rail (P9).
Insert 6 x Cam Nuts (H4) into the holes of Side Panels (P2,P3) and Divider (P4).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Top Panel (P1) and tighten the cam nuts.
6 x Cam Nuts
(H4)
H4
H4
H1
H4

H10
H10
H11 H11
H11
H11
Page 9
Step 13
You will need:
4 x Small Cam
Bolts
(H10)
Step 14
Step 15
You will need:
(P13)
(P13)
(P13)
(P17)
(P15)
(P15)
(P16)
(P16)
Attach 4 x Small Cam Bolts (H10) into Drawer Front (P13).
4 x Small Cam
Nuts
(H11)
Slide Drawer Base (P17) into the groove in
Drawer Sides (P15) and (P16).
Insert 4 x Small Cam Nuts (H11) into the holes of Drawer Sides (P15) and (P16).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Drawer Sides (P15) and (P16) into place and tighten the cam nuts.
H10 H10
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.

H2
Page 10
Step 16
You will need:
4 x Long Screws
(H2)
Step 17
You will need:
1 x DR Runner
(H9)
1 x DL Runner
(H8)
4 x Small
Screws
(H5)
Step 18 Step 19
(P13)
(P13)
(P13)
(P18)
(P15)
(P16)
H2
H2
H2
Attach 1 x DL Runner (H8) to the bottom of
Left Drawer Side (P15) and 1 x DR Runner (H9) to the
bottom of Right Drawer Side (P16) with 4 x Small Screws (H5).
Attach Drawer Back (P18) to Drawer Sides (P15)
and (P16) with 4 x Long Screws (H2),make sure that
the groove lines up the whole way around the drawer.
(P14)
Repeat step 13 to step 17 with Drawer Front (P14)
to assemble the other drawer.
H9
H8
DR
DL
H5
H5
H5
H5
(P15)
(P16)
H9
H8
H5
H5
H5
H5