fantastic furniture Java Dresser 3 Drawer User manual

Version 1.0
Java
Dresser 3 Drawer
fantasticfurniture.com.au
Required
Two People

fantasticfurniture.com.au Page 2
Warning: Ensure the wall strap is attached
to avoid serious injury
To avoid any serious or fatal injury, a wall strap has been provided with
this product to prevent toppling. We strongly recommend that this
product is permanently fixed to the wall or other suitable surface. Fixing
of what fixing device to use.
Rattan
Rattan is a natural material that will respond to humidity in the
environment. Low humidity may cause the rattan to shrink.
High humidity may cause the rattan to absorb moisture and expand,
causing the weaving to look loose and wavy.
This is a natural phenomenon and not a defect.
Looks like you’ve found
your Fantastic!
Love it? Share it!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
Fantastic buy! Share how it looks at home on Instagram
for your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
!If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
!Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au Page 3

Parts list
1 x Top Panel (P1)
1 x Bottom Panel (P2)
1 x Left Side Panel (P3)
1 x Right Side Panel (P4)
3 x Drawer Fronts (P5)
What you need
to assemble the product
Other tools you need
Flat Head Screwdriver;
Phillips Head Screwdriver;
Mallet
fantasticfurniture.com.au
Page 4
Top Panel (P1)
Bottom Panel (P2)
Left Side
Panel (P3)
Right Side
Panel (P4)
Drawer Front (P5)
(P5)
Back Panel (P13)
Metal Rail
(P12)
Front
Rail
(P14)
Leg (P11)
Leg (P11)
Drawer Support
(P10)
Drawer Base
(P9)
Drawer Back (P8)
Drawer
Left
Side (P6) Drawer
Right
Side (P7)
(P6)
(P6)
(P7)
(P8)
(P9)
(P7)
(P8)
(P9)
(P10)
(P10)
Drawer Front (P5)
3 x Drawer Left Sides (P6)
3 x Drawer Right Sides (P7)
3 x Drawer Backs (P8)
3 x Drawer Bases (P9)
6 x Drawer Supports (P10)
4 x Legs (P11)
1 x Metal Rail (P12)
1 x Back Panel (P13)
2 x Front Rails (P14)

fantasticfurniture.com.au
Page 5
Hardware Pack
32 x Cam Bolts
(H1)
8 x Large Cam
Nuts (H2)
12 x Dowels ø8mm
(H3)
6 x Handles
(H4)
6 x Screws 16mm
(H6)
12 x Flat Washers
(H9)
8 x Spring
Washers (H10)
12 x Screws 28mm
(H11)
1 x Allen Key
(H12)
4 x Felt Feet
(H5)
8 x Bolts 55mm
(H8)
6 x Back Panel
Connectors (H7)
2 x Screws 25mm
(H14)
24 x Small Cam
Nuts (H15)
2 x Wall Straps
(H13)
6 x Dowels ø6mm
(H16)
28 x Screws 38mm
(H17)
6 x Slides
(H19)
36 x Screws 12mm
(H18)
4 x Bolts 50mm
(H20)

Step 1
Page 6fantasticfurniture.com.au
You will need
Attach 1 x felt foot (H5) onto each leg (P11) as shown.
Step 2
You will need
8 x Bolts
(H8)
Attach 1 x leg (P11) onto bottom panel (P2),using 2 x bolts (H8), 2 x spring washers (H10)
and 2 x flat washers (H9).
Tighten the bolts with allen key (H12).
Repeat this step for the other 3 x legs (P11).
With assistance turn the assembled frame over.
(P11)
4 x Felt Feet
(H5)
X4
H5
8 x Flat
Washers (H9)
8 x Spring
Washers (H10)
1 x Allen Key
(H12)
(P11)
H12
H8
H9
H10
(P2)
(P11)
(P11)
(P2)
(P11) (P11)
Required
Two People

Step 3
Page 7fantasticfurniture.com.au
You will need
Phillips Head
Screwdriver
18 x Screws
12mm (H18)
6 x Slides
(H19)
Mallet
H19
Separate the 6 x slide runners (H19-2) and slide tracks (H19-1)
from the slides (H19) by following the steps below:
Extend the slide runner (H19-2) all the way out.
Press down the plastic release lever on the slide track (H19-1)
and pull out the slide runner (H19-2) completely.
H19
Slide runner H19-2 Slide track H19-1
H19-1
H19-1
Note the position of the rubber stopper
Attach 6 x separated slide tracks (H19-1)
onto side panel (P3, P4) with 18 x screws (H18),
using a phillips head screwdriver as shown.
Ensure the slide tracks (H19-1) are attached so the rubber stopper is positioned
near the grooves on side panel (P3, P4) as shown.
Screw 2 x cam bolts (H1) into each side panel (P3, P4),
using a phillips head screwdriver.
Insert 4 x dowels (H3) into each panel (P3) & (P4) as shown.
If needed use a mallet to gently tap the dowels into place.
Adjust runner to access the screw holes.
H19-1
8 x Dowels
ø8mm (H3)
4 x Cam Bolts
(H1)
(P3)
(P4)
H3
H3
H3
H3
H3
H3
H3
H3
H1
H1
H1
H1
H18
H18
H18
H18
H18
H18
H18
H18
H18
H18
H18
H18
H19-1
H19-1
H19-1
H19-1
H19-1
H19-1
H19-1
Please fasten the screws through
these holes for this step.

Step 4
Page 8fantasticfurniture.com.au
You will need
Insert 2 x dowels (H3) into each front rail (P14) as shown.
Use a mallet to gently tap the dowels into place if needed.
With assistance, position 2 x front rails (P14) between side panels (P3, P4),
ensuring the grooves on the side panels (P3, P4) are on the same side.
Insert 4 x large cam nuts (H2) into front rails (P14).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Using a flat head screwdriver turn clockwise to lock.
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
(P14)
X2
Mallet
4 x Dowels
ø8mm (H3)
H3
H3
Step 5
You will need
Flat Head
Screwdriver
4 x Large Cam
Nuts (H2)
Required
Two People
(P3)
(P4)
(P14)
(P14)
H2
H2
H2
H2
Laminated edge

Step 6
Page 9fantasticfurniture.com.au
You will need
With assistance, position bottom panel (P2)
to side panels (P3, P4), ensuring the grooves
on all the panels (P2, P3, P4) align.
Screw 4 x screws (H17) into side panels (P3, P4),
using a phillips head screwdriver.
With assistance, carefully turn the assembled frame over.
Step 7
Unfold and slide back panel (P13) into the grooves on side panels (P3, P4)
and bottom panel (P2).
(P13)
(P3)
(P4)
(P2)
(P3)
(P4)
(P2)
H17
Required
Two People
Phillips Head
Screwdriver
4 x Screws
38mm (H17)
H17
H17
H17

Step 8
Page 10fantasticfurniture.com.au
You will need
With assistance, position top panel (P1) onto
the assembled frame as shown.
Insert 4 x large cam nuts (H2) into panels (P3, P4).
Rotate the cam nuts so the arrows point towards
the incoming cam bolts.
Using a flat head screwdriver turn clockwise to lock.
Step 9
You will need
Flat Head
Screwdriver
4 x Large Cam
Nuts (H2)
(P1)
(P3) (P4)
H2
H2
H2
H2
Required
Two People
Screw 4 x cam bolts (H1) into top panel (P1), using a phillips head screwdriver.
Attach metal rail (P12) onto top panel (P1) with 4 x bolts (H20),
using a phillips head screwdriver.
4 x Cam Bolts
(H1)
Phillips Head
Screwdriver
4 x Bolts
35mm (H20)
(P1)
H1 H20
(P12)
H1
H1
H1
H20
H20
H20