fantastic furniture COMO User manual

Version 1.0
Como
Bedside 2 Drw
fantasticfurniture.com.au

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love！
Recommended weight capacity : 50kgs on top.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Left Side Panel (P2);
Right Side Panel (P3);
2 x Rails (P4);
Rail (P5);
2 x Rails (P6);
Back Panel (P7);
2 x Drawer Fronts (P8)
2 x Left Drawer Sides (P9);
2 x Right Drawer Sides (P10);
2 x Drawer Bases (P11);
2 x Drawer Backs (P12);
Hardware pack
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
Top Panel
(P1)
Right Side
Panel
(P3)
Left Drawer Side
(P9)
Drawer Front
(P8)
×2
Right Drawer
Side (P10)
Drawer Back
(P12)
Drawer Base
(P11)
Left Side
Panel
(P2)
Rail
(P4)
Rail
(P4)
Rail
(P5)
Rail
(P6)
Rail
(P6)
Back Panel
(P7)
18 x Dowels
(H1)
8 x Long Screws
(H2)
32 x Small Screws
(H5)
2 x CL Runner
Tracks
(H6)
10 x Cam Bolts
(H3)
10 x Cam Nuts
(H4)
8 x Small
Cam Nuts
(H11)
2 x CR Runner
Tracks
(H7)
2 x DL Runners
(H8)
2 x DR Runners
(H9)
8 x Small
Cam Bolts
(H10)
4 x Plastic
Glides
(H12)
8 x Wedges
(H13)
8 x Screws
(H14)

You will need
Step 3
7 x Dowels
(H1)
Phillips Head
Screwdriver
6 x Small
Screws (H5)
H5
H5
H5
H5
H5
H6
H6
H5
(P2)
H5
H5
H5
H5
H5
H7
H7
H5
(P3)
H7
CR
H5
6 x Small
Screws (H5)
6 x Cam Bolts
(H3)
You will need
Step 1
Step 2
You will need
Phillips Head
Screwdriver
Attach 2 x CL Runner Tracks (H6) to Left Side Panel (P2) with 6 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
Attach 2 x CR Runner Tracks (H7) to Right Side Panel (P3) with 6 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 5
2 x CL Runner
Tracks (H6)
H6
CL
H5
2 x CR Runner
Tracks (H7)
Phillips Head
Screwdriver
H3
H3
H3
(P3)
(P2)
H1
H1
H1
H1
H1
H1
H1
H3
H3
H3
Insert 7 x Dowels (H1) into Left Side Panel
(P2). Attach 6 x Cam Bolts (H3) into Side Panels
(P2) and (P3) as shown. Tighten with a Phillips Head Screwdriver.

This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Step 5
You will need
3 x Dowels
(H1)
7 x Cam Nuts
(H4)
Phillips Head
Screwdriver
Step 4
You will need
3 x Cam Nuts
(H4)
Phillips Head
Screwdriver
Insert 3 x Cam Nuts (H4) into the
holes of Rails (P5) and 2 x Rails (P6).
Rotate the cam nuts so the arrows point
towards the incoming cam bolts. Attach 2 x Rails (P4) ,
Rails (P5) and 2 x Rails (P6) to Left Side Panel (P2), then tighten the cam nuts.
(P4) (P6)
(P5)
(P4)
(P6)
(P2)
(P3)
H4
H4
H4
H1 H1
H1 H1
H1
H1
H1
Insert 7 x Dowels (H1) into 2 x Rails (P4),
Rail (P5) and 2 x Rails (P6).Insert 3 x Cam
Nuts (H4) into the holes of Rails (P5) and
2 x Rails (P6).Rotate the cam nuts so the
arrows point towards the incoming cam bolts.
Push Right Side Panel (P3) into place and tighten
the cam nuts.
fantasticfurniture.com.au
fantasticfurniture.com.au Page 6
(P4)
(P6)
(P5)
(P4)
(P6)
(P2)
H4
H4
H4
H4

4 x Cam Nuts
(H4)
Hammer
You will need
Phillips Head
Screwdriver
Step 7
4 x Cam Bolts
(H3)
You will need
Step 6
Put Back Panel (P7) into the groove on the back of the chest, screw it with 12 x Small Screws (H5).
Then hammer 4 x Plastic Glides (H12) on Side Panels (P2) and (P3).
(P1)
H3
H3
H3
H3
Attach 4 x Cam Bolts (H3) into Top Panel (P1) as shown. Tighten with a Phillips Head Screwdriver.
(P2)
(P3)
H1 H1
H4 H4
H4
H4
H1
H1
Insert 4 x Dowels (H1) into Side Panels (P2)
and (P3).Insert 4 x Cam Nuts (H4) into the holes of
Side Panels (P2) and (P3).Rotate the cam nuts so the
arrows point towards the incoming cam bolts.
Attach Top Panel (P1) and tighten the cam nuts.
fantasticfurniture.com.au Page 7
H5
(P7)
H12
H12
H12
H12
12 x Small
Screws (H5)
4 x Plastic
Glides (H12)
H5
H12
20mm
You will need
Step 8
4 x Dowels
(H1)
Phillips Head
Screwdriver

You will need
Step 10
Attach 4 x Small Cam Bolts (H10) into Drawer Front (P8). Tighten with a Phillips Head
Screwdriver.
Attach 8 x Cam Bolts (H3) to Drawer Fronts (P7x2). Tighten with a Phillips Head Screwdriver.
You will need
Step 9
4 x Cam Nuts
(H4)
Phillips Head
Screwdriver
4 x Small
Cam Bolts (H3)
(P8)
fantasticfurniture.com.au Page 8
Phillips Head
Screwdriver
H3
H3
H3
H3
H11
H11
H11
H11
(P8)
(P9)
(P10)

Attach Drawer Back (P12) to Drawer
Sides (P9) and (P10) with 4 x Long Screws (H2),
make sure that the groove lines up the whole way
around the drawer.
Step 11
H14
H14
H14
H14 H14 H13
H13
H13
H13
H13
Slide Drawer Base (P11) into the groove in Drawer Sides (P9) and (P10).
fantasticfurniture.com.au Page 9
You will need
Step 12
Phillips Head
Screwdriver
4 x long
Screws (H2)
You will need
Step 13
Phillips Head
Screwdriver
(P8)
(P11)
(P9)
(P10)
H2
(P11)
(P12)
(P8)
(P9)
(P10)
H2
H2
H2
4 x Wedges
(H13)
4 x Screws
(H14)
Attach 4 x Wedges (H13) into the gap between
Drawer Sides (P9,P10) and Drawer Base (P11) with 4 x Screws (H14).

Step 15
Insert the assembled drawers into the corresponding compartments as shown.
Ensure the drawers slide easily along the rails.
fantasticfurniture.com.au Page 10
You will need
Step 14
4 x Small
Screws (H5)
Phillips Head
Screwdriver
1 x DR
Runner (H9)
1 x DL
Runner (H8)
(P9)
(P10)
H9
H8
H5
H5
H5
H5
Attach 1 x DL Runner (H8) to the bottom of Left Drawer Side (P9) and 1 x DR Runner (H9)
to the bottom of Right Drawer Side (P10) with 4 x Small Screws (H5). Repeat step 9 to step 14
to assemble the other drawer.