fantastic furniture Hamilton Lowline Small User manual

Version 1.0
Hamilton
Lowline Small
fantasticfurniture.com.au

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
Recommended weight capacity : 50kgs on top.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Left Side Panel (P2);
Right Side Panel (P3);
Shelf Panel (P4);
Rail (P5);
Rail (P6);
Back panel (P7);
Back panel(P8):
2 x Drawer Fronts (P9):
2 xLeft Drawer Sides (P10) :
2 x Right Drawer Sides (P11);
2 x Drawer Bases (P12);
2 x Drawer Backs (P13);
Divider (P14);
Divider (P15)
Hardware pack
Left Drawer
Side (P10)
Right Drawer
Side (P11)
Drawer Back
(P13)
Drawer
Base (P12)
Drawer
Front (P9)
Top Panel
(P1)
Right Side
Panel
(P3)
Left Side
Panel (P2)
Back
Panel
(P7)
Back
Panel
(P8)
Rail
(P5)
Rail
(P6)
Shelf
Panel
(P4)
Divider
(P14)
Divider
(P15)
27 x Cam
Bolts
(H3)
27 x Cam
Nuts
(H4)
8 x Dowels
(H1)
20 x Small
Screws
(H5)
2 x CL Runner
Tracks
(H6)
2 x CR Runner
Tracks
(H7)
2 x DR Runners
(H9)
2 x Handle Bolt
(H11)
2 x Handle
(H10)
2 x DL Runners
(H8)
12 x Large
Screws
(H2)
4 x Wedges
(H12)
4 x Wedge
Screws
(H13)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
x 2

6 x Small
Screws (H5)
6 x Dowels
(H1)
(P3)
(P3)
(P2)
(P2)
You will need
Step 1
H7
CR
H5
Step 2
You will need
Phillips Head
Screwdriver
10 x Cam Bolts
(H3)
Phillips Head
Screwdriver
Attach 1 x CL Runner Track (H6) to Left Side Panel (P2) and 1 x CR Runner Track (H7) to the
Right Side Panel (P3) with 6 x Small Screws (H5) by tightening with the Phillips Head Screwdriver.
Insert 6x dowels (H1) to Left & Right Side Panels (P2&P3) as shown. Attach 10 x
Cam Bolts (H3) to Left & Right Side Panels (P2&P3) by tightening with the Phillips
Head Screwdriver.
fantasticfurniture.com.au Page 5
1 x CL Runner
Tracks (H6)
H6
CL
H5
H5
H7
H6
H5
H3
H1
H3
H1
1 x CR Runner
Tracks (H7)
C

You will need
Step 3
Step 4
You will need
Attach 1 x CL Runner Track (H6) to Divider (P15) with 6 x Small Screws (H5) by tightening with
the Phillips Head Screwdriver. Flip the Divider (P15) ,and attach 1 x CR Runner Track (H7) to
Divider (P15) with 6 x Small Screws (H5) by tightening with the Phillips Head Screwdriver.
Attach 2 x Cam Bolts (H3) into Shelf Panel (P4). Insert 2 x Dowels (H1) into Divider (P14)
as shown. Attach Divider (P14) to Shelf Panel (P4) with 2 x Large Screws (H2) by tightening with
the Phillips Head Screwdriver.
Phillips Head
Screwdriver
2 x Dowels
(H1)
Phillips Head
Screwdriver
FLIP
(P15) (P15)
(P14)
(P4)
fantasticfurniture.com.au
fantasticfurniture.com.au Page 6
H5
H1
H1 H3
H3
H2
H2
H7
H6
6x Small
Screws (H5)
1 x CL Runner
Tracks (H6)
1 x CR Runner
Tracks (H7)
2 x Cam Bolts
(H3)
H5
H7
CR
H5
H6
CL
H5
2 x Large
Screws (H2)

Attach 1 x Cam Bolt (H3) into Rail (P5) by tightening with the Phillips Head Screwdriver. Insert 1
x Cam Nut (H4) into the hole of Rail (P5). Rotate the cam nuts so the arrow points towards the
incoming cam bolts. Attach Rails (P5) to Divider (P15) by tightening with the Phillips Head
Screwdriver.
Attach Rail (P6) to Divider (P15) with 2 x Large Screws (H2) by tightening with the Phillips
Head Screwdriver.
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
You will need
Phillips Head
Screwdriver
Step 6
You will need
Step 5
1 x Cam Nuts
(H4)
Phillips Head
Screwdriver
(P15)
(P15)
(P5)
(P5)
(P6)
fantasticfurniture.com.au Page 7
H2 H2
H4
H3
2 x Large
Screws (H2)
Cam nut hole must
face downward
Caution!!
1 x Cam Bolts
(H3)

You will need
Step 7
Insert 2 x Cam Nuts (H4) into the holes of Divider (P15). Rotate the cam nuts so the arrow
points towards the incoming cam bolts. Attach Divider (P15) to Shelf Panel (P4) by tightening
with the Phillips Head Screwdriver.
Insert 5 x Cam Nuts (H4) into the holes of Rails & Shelf Panel (P5 & P6 & P4). Rotate
the cam nuts so the arrow points towards the incoming cam bolts. Attach Rails & Shelf
Panel (P5 & P6 & P4) to Left Side Panel (P2) by tightening with the Phillips Head
Screwdriver. Slide Back Panel (P8) into the grooves of Rail & Shelf Panel (P6&P4).
Phillips Head
Screwdriver
2 x Cam Nuts
(H4)
You will need
Step 8
Phillips Head
Screwdriver
5 x Cam Nuts
(H4)
(P15)
(P5)
(P5)
(P8)
(P4)
(P4)
(P6)
(P6)
(P2)
H4
H4
H4
H4
H4
fantasticfurniture.com.au Page 8

You will need
Step 10
Attach 6 x Cam Bolts (H3) to Top Panel (P1) by tightening with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
You will need
Step 9
Insert 5 x Cam Nuts (H4) into the holes of Rails & Shelf Panel (P5 & P6 & P4). Rotate the cam
nuts so the arrow points towards the incoming cam bolts. Attach Rails & Shelf Panel
(P5 & P6 & P4) to Right Side Panel (P3) by tightening with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
5 x Cam Nuts
(H4)
(P4)
(P6)
(P3)
(P2)
H4
H4
H4
fantasticfurniture.com.au Page 9
(P1)
H3
H3
H3
H3
H3
H3
6 x Cam Bolts
(H3)

You will need
Step 11
Phillips Head
Screwdriver
6 x Cam Nuts
(H4)
Gently stand the unit upright.
Slide Back Panel (P7) into the
grooves of Left & Right Side
Panel (P2&P3). Insert 6 x Cam
Nuts (H4) into Divider & Right &
Left Side Panels (P14&P3&P2)
as shown. Rotate the cam nuts
so the arrows point towards
the incoming cam bolts. Attach
Top Panel (P1) to unit by tightening
cam nuts with the Phillips Head Screwdriver.
Secure Back Panels (P7 & P8) in place with 4 x Wedges (H12) using 4 x Wedge Screws (H13)
by tightening with the Phillips Head Screwdriver.
Step 12
You will need
Phillips Head
Screwdriver
4 x Wedges
(H12)
4 x Wedge
Screws (H13)
H4
H4
H4
H4
H12
H13
fantasticfurniture.com.au Page 10
(P3)
(P4)
(P7)
(P1)
(P1)
(P7)
(P8)
(P2)

You will need
Step 13
Phillips Head
Screwdriver
x2
You will need
Step 14
8 x Cam Nuts
(H4)
Insert 8 x Cam Nuts (H4) into Left & Right
Drawer Sides (P10x2&P11x2) as shown. Rotate
the cam nuts so the arrows point towards the incoming
cam bolts. Attach Left & Right Drawer Sides (P10x2&P11x2) to
Drawer Fronts (P9x2) by tightening the cam nuts with the Phillips Head Screwdriver.
Attach 8 x Cam Bolts (H3) to Drawer Fronts (P9x2) by tightening with the Phillips
Head Screwdriver.
(P10)
(P11)
(P9)
Phillips Head
Screwdriver
H4
H4
H4
H4
x2
fantasticfurniture.com.au Page 11
(P9)
H3 H3
H3 H3
8 x Cam Bolts
(H3)
Slide Drawer Bases (P12x2) into the grooves of Left & Right Drawer Sides (P10x2&P11x2).
(P10)
(P11)
(P12)
Step 15
x2

Attach Drawer Backs (P13x2) to Left &
Right Drawer Sides (P10x2&P11x2) with 8
x Large Screws (H2) by tightening with the Phillips
Head Screwdriver. Ensure the Drawer Base
lines up with the grooves the whole way around
the drawer before securing.
x2
x2
Attach 2 x DL Runners (H8) to the bottom of Left Drawer Sides (P10x2) and 2 x DR
Runners (H9) to the bottom of Right Drawer Sides (P11x2) with 8 x Small Screws (H5)
by tightening with the Phillips Head Screwdriver.
(P10)
(P10)
(P11)
(P11)
(P13)
fantasticfurniture.com.au Page 12
H2
H2
H2
H2
You will need
Step 16
You will need
Step 17
8 x Small
Screws (H5)
Phillips Head
Screwdriver
2 x DR
Runners (H9)
2 x DL
Runners (H8)
Phillips Head
Screwdriver
8 x Large
Screws (H2)
H5
H5
H5
H5 H9
H8

Attach 2 x Handles (H11) to Drawer Fronts (P9x2) with 2 x Handle Bolts (H10) by tightening
with the Phillips Head Screwdriver.
Step 19
Carefully insert the drawers into the lowline by gently guiding the runners into the tracks.
(P9)
fantasticfurniture.com.au Page 13
You will need
Step 18
x2
H11
H10
2 x Handle
Bolts (H11)
2 x Handles
(H10)
Phillips Head
Screwdriver

Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
fantasticfurniture.com.au Page 14