fantastic furniture JUNO User manual

Version 1.0
JUNO
DESK 2 DRAWER
www.fantasticfurniture.com.au

Enjoy
Your purchase from
Australia’s Best Value Furniture Store
www.fantasticfurniture.com.au PAGE 2
Recommended weight capacity : 50KG.

Assembly checklist
Useful Information
www.fantasticfurniture.com.au PAGE 3
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Please see page 2 for any safety requirements or weight restrictions.

Back
Panel
(P7)
Top panel
(P1)
16 x Long Screws
(H2) 20 x Small Screws
(H5) 2 x CL Runner
Tracks
(H6)
16 x Cam Bolts
(H3) 16 x Cam Nuts
(H4)
2 x CR Runner
Tracks
(H7)
2 x DL
Runners
(H8)
2 x DR
Runners
(H9)
What you need
to assemble the product
Other tools you need
Phillips head screwdriver;
www.fantasticfurniture.com.au PAGE 4
DO NOT USE
Right
Side
Panel
(P3)
Bottom Panel
(P4)
Left divider
(P5)
4 x Legs
(P8)
Left
Side
Panel
(P2)
16 x Dowels
(H1)
Left Drawer
Side (P10)
Right
Drawer Side
(P11)
x 2
Drawer Back
(P12)
Drawer
Base
(P13) Drawer Front
(P9)
12 x Bolts
(H10)
Parts list
Box 1: Top panel (P1);
Left Side Panel(P2);
Right Side Panel (P3);
Bottom Panel (P4);
Left Divider (P5);
Right Divider (P6);
Back Panel (P7);
4 x Leg (P8);
2 x Drawer Front (P9);
2 x Left Drawer Side (P10);
2 x Right Drawer Side(P11);
2 xDrawer Back (P12);
2 x Drawer Base (P13);
Rail (P14)
Hardware Pack
4 x Wedges
(H11) 4 x Screws
(H12)
Right divider
(P6)
4 x Long Bolts
(H13)
Rail
(P14)
1 x Allen Key
(H14) 4 x Felt Pads (H15)

www.fantasticfurniture.com.au PAGE 5
Attach 8 x cam bolts (H3) to top panel (P1) as shown.Tighten with a Phillips head screwdriver.
Phillips head
screwdriver
You will need
Step 1
You will need
Phillips head
screwdriver
6 x Small
Screws (H5)
1 x CL Runner
Tracks (H6)
Step 2
8 x Cam
Bolts (H3)
H3
(P1)
(P2)
H6
H5
(P3)
H7
H5
1 x CR Runner
Tracks (H7)
Attach 1 x CL runner tracks (H6) to left side panel (P2) with 3 x small screws (H5).
1 x CR runner tracks (H7) to right side panel (P3) with 3 x small screws (H5).
Tighten with a Phillips head screwdriver.
H7
CR
H5
H6
CL
H5

www.fantasticfurniture.com.au PAGE 6
Attach 1 x CR runner tracks (H7) to left divider (P5) with 3 x small screws (H5). Attach 1 x CL runner
tracks (H6) to right divider (P6) with 3 x small screws (H5). Tighten with a Phillips head screwdriver.
You will need
Step 3
Step 4
You will need
(P6)
H6
H5
(P5)
H7
H5
(P1)
(P2)
(P3)
(P5)
(P6)
Phillips head
screwdriver
6 x Small
Screws (H5)
1 x CL Runner
Tracks (H6) 1 x CR Runner
Tracks (H7)
8 x Cam
Nuts (H4)
8 x Dowels
(H1)
H4
H1
Attach left side panel (P2) ,right side panel (P3) ,left divider (P5) and right divider (P6)
to top panel (P1) with 8x dowels (H1),and secure with 8x cam nuts (H4).
Tighten with a Phillips head screwdriver.
H7
CR
H5
H6
CL
H5
H4 H1
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Phillips head
screwdriver

www.fantasticfurniture.com.au PAGE 7
Slide back panel (P7) into the groove of left side panel (P2) and right side panel (P3).
Attach rail (P14) to bottom panel (P4) secure with 4 x long bolts (H13).Tighten with an Allen key (H14).
Attach bottom panel (P4) to the main unit with 8x dowels (H1), and secure with 8x long screws (H2).
Tighten with a Phillips head screwdriver.
You will need
Step 6
You will need
Step 5
8 x Dowels
(H1)
8 x Long
Screws (H2)
(P3)
(P2)
(P5)
(P6)
(P4)
12 x Bolts
(H10)
(P7)
H2
H1
H10
(P4)
(P8)
Attach 4x legs (P8) to bottom panel (P4) and secure with 12 x bolts (H10). Tighten
with an Allen key (H14).Apply 4 x felt pads (H15) to bottom of legs (P8) as shown.
H10
(P8)
(P4)
Phillips head
screwdriver
4 x Long Bolts
(H13)
H13
(P14)
H14
1 x Allen Key
(H14)
H13
H14
1 x Allen Key
(H14)
4 x Felt Pads
(H15)
H15
Ensure laminated
side of panel is
facing inwards.
(P8)
H15

www.fantasticfurniture.com.au PAGE 8
Screw 4 x cam bolts (H3) into drawer front (P9) with a Phillips head screwdriver.
Repeat for second drawer.
Attach drawer sides (P10, P11) to drawer front (P9). Insert 4 x cam nuts (H4) into the
holes of drawer sides (P10, P11). Make sure the opening on cam nuts point towards
the incoming cam bolts. Tighten the cam nuts using a Phillips head screwdriver.
Repeat for second drawer.
You will need
Step 8
Step 7
H3
(P9)
H4
x 2
x 2
(P9)
(P10)
(P11)
Phillips head
screwdriver
You will need
8 x Cam
Bolts (H3)
8 x Cam
Nuts (H4)
H4
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Phillips head
screwdriver

Slide drawer base (P13) into the groove of drawer sides (P10, P11).Repeat for second drawer.
Step 9
Attach drawer back (P12) to drawer sides (P10, P11) with 4 x long screws (H2), make
sure that the groove lines up the whole way around the drawer. Tighten screws using
a Phillips head screwdriver.Repeat for second drawer.
Step 10
www.fantasticfurniture.com.au PAGE 9
x 2
x 2
H2
(P9)
(P10)
(P11)
(P12)
(P10)
(P11)
(P13)
You will need
Phillips head
screwdriver
8 x Long
Screws (H2)
Ensure laminated
side of panel is
facing inwards.

You will need
Step 11
Attach 1 x DL runner (H8) to left drawer side (P10) and 1 x DR runner (H9) to right drawer
side (P11) with 4 x small screws (H5). Tighten screws using a Phillips head screwdriver.
Repeat for second drawer.
Carefully turn the desk over to an upright position. Slide the drawers into the desk front.
Step 12
www.fantasticfurniture.com.au PAGE 10
Phillips head
screwdriver
H8
H9
x 2
H5
H5
(P9)
(P10)
(P11)
8 x Small
Screws (H5)
2 x DL Runner
(H8) 2 x DR Runner (H9)