fantastic furniture Toronto Hall Table 2 Drawer User manual

Version 1.0
Cove
Coee Table 2 Drawer
fantasticfurniture.com.au

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
Recommended weight capacity : 15kgs/drawer.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Bottom Panel (P2);
2 x Side Panels (P3);
Divider (P4);
2 x Dividers (P5);
4 x Legs (P6);
2 x Drawer Fronts (P7):
2 x Left Drawer Sides (P8) :
2 x Right Drawer Sides (P9);
2 x Drawer Bases (P10);
2 x Drawer Backs (P11);
Hardware pack
Top Panel
(P1)
Bottom Panel
(P2)
Drawer
Fronts (P7)
Left
Drawer Sides
(P8)
Right
Drawer Sides
(P9)
Drawer
Bases (P10)
Drawer
Backs (P11)
Legs
(P6)
Side Panel
(P3)
Side Panel
(P3)
Divider
(P4)
Divider
(P5)
Divider
(P5)
4 x Plastic
Glides
(H11)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
20 x Dowels
(H1)
14 x Long Screws
(H2)
20 x Small
Screws
(H5)
2 x CL Runner
Tracks
(H6)
14 x Cam Bolts
(H3)
14 x Cam Nuts
(H4)
2 x CR Runner
Tracks
(H7)
2 x DL Runners
(H8)
2 x DR Runners
(H9)
x4
x2
20 x Screws
(H10)
4 x Brackets
(H12)

6 x Small
Screws (H5)
(P1)
(P3)
You will need
Step 1
Step 2
You will need
Phillips Head
Screwdriver
Phillips Head
Screwdriver
6 x Cam Bolts
(H3)
Attach 6 x Cam Bolts (H3) to Top Panel (P1) by tightening with the Phillips Head Screwdriver.
Attach 2x CL Runner Tracks (H6) to Side Panels (P3 x 2) with 6 x Small Screws (H5)
by tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 5
2 x CL Runner
Tracks (H6)
H6
CL
H5
H5
H5
H5
H6
H3
H3 H3
H3 H3
H3
X2

You will need
Step 3
Step 4
You will need
Attach 2 x CR Runner Tracks (H7) to Divider (P4) with 6 x Small Screws (H5) by tightening
with the Phillips Head Screwdriver.
Insert 6 x Cam Nuts (H4) into Side Panels (P3 x 2) and Divider (P4) as shown.
Rotate the cam nuts so the arrow points towards the incoming cam bolts.
Attach Side Panels (P3 x 2) and Divider (P4) to Top Panel (P1) by tightening
with the Phillips Head Screwdriver.
6 x Cam Nuts
(H4)
Phillips Head
Screwdriver
Phillips Head
Screwdriver
6 x Small
Screws (H5)
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
(P1)
(P4)
(P4)
(P4)
(P3)
(P3)
fantasticfurniture.com.au Page 6
2 x CR Runner
Tracks (H7)
H5
H5
H5
H5
H4
H4
H4
H4
H4
H1
H1
H1
H1
H1
H1
H5
H5
H7
H7
FLIP
H7
CR
H5
6 x Dowels
(H1)

Attach 2 x Dividers (P5 x 2) to Top Panel (P1) with 4 x Dowels (H1) by tightening
with the Phillips Head Screwdriver.
Attach 10 x Dowels (H1) to Side Panels (P3 x 2) and Dividers (P4, P5 x 2).
You will need
Step 6
You will need
Step 5
4 x Dowels
(H1)
(P1)
(P3)
(P3)
(P3)
(P3)
(P4)
(P4)
(P5)
(P5)
(P5)
(P5)
fantasticfurniture.com.au Page 7
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
10 x Dowels
(H1)

You will need
Step 7
Secure Bottom Panel (P2) to Side Panels (P3 x 2) and Divider (P4) with 6 x Long Screws (H2)
by tightening with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
Phillips Head
Screwdriver
You will need
Step 8
(P2)
(P2)
(P3)
(P3)
(P4)
fantasticfurniture.com.au Page 8
6 x Long
Screws (H2)
H2
H2
H2
H2
H2
H2
4 x Brackets
(H12)
20 x Screws
(H10)
H10
H10
H10
H10
H10
H10
H12
H12
H12
H12
H12
Attach 4 x Brackets (H12) to Bottom Panel (P2) with 20 x Screws (H10) as shown.
Tighten with a Phillips Head Screwdriver.

You will need
Step 10
Phillips Head
Screwdriver
Attach 4 x Cam Bolts (H3) to Drawer Front (P7) by tightening with the Phillips Head
Screwdriver.
x2
Turn 4 x Legs (P6) into brackets until firm. Hammer 4 x Plastic Glides (H11) on
Legs (P6 x 4) as shown.
You will need
Step 9
fantasticfurniture.com.au Page 9
8 x Cam Bolts
(H3)
H3 H3
H3 H3
(P7)
(P2)
(P6)
(P6)
(P6)
(P6)
H11
H11
H11
H11
Hammer
4 x Plastic
Glides (H11)

Attach Drawer Back (P11) to Left & Right Drawer Side (P8 & P9) with 4 x Long Screws (H2)
by tightening with the Phillips Head Screwdriver.
x2
You will need
Step 11
Phillips Head
Screwdriver
fantasticfurniture.com.au Page 10
Step 12
(P11)
(P9)
(P8)
8 x Long
Screws (H2)
H2
H2
H2
H2
Slide Drawer Base (P10) into the grooves of Left & Right Drawer Side (P8 & P9).
(P10)
(P8)
(P9)
x2

Attach 1 x DL Runner (H8) to the bottom of Left Drawer Side (P8) and 1 x DR Runner (H9)
to the bottom of Right Drawer Side (P9) with 4 x Small Screws (H5) by tightening with the
Phillips Head Screwdriver.
x2
x2
fantasticfurniture.com.au Page 11
H4H4
H4
H5
H5
H8
H9
H5
H5
H4
You will need
Step 14
Phillips Head
Screwdriver
Insert 4 x Cam Nuts (H4) into Left & Right Drawer Side (P8 & P9) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts. Attach Drawer
Front (P7) to Left & Right Drawer Side (P8 & P9). Make sure that the groove lines up
the whole way around the drawer. Tighten with a Phillips Head Screwdriver.
8 x Small
Screws (H5)
2 x DR
Runners (H9)
2 x DL
Runners (H8)
8 x Cam Nuts
(H4)
You will need
Step 13
Phillips Head
Screwdriver (P9)
(P9)
(P8)
(P8)
(P7)

Carefully insert the drawers into the table by gently guiding the runners into the tracks.
Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
fantasticfurniture.com.au Page 12
Step 15