fantastic furniture Como TV Stand Rectangle User manual

Version 1.0
Como
TV Stand Rectangle
fantasticfurniture.com.au

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love！
Recommended weight capacity : 50kgs on top.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Hardware pack
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
Top Panel
(P1)
Shelf Panel
(P2)
Divider
(P5)
Divider
(P5)
Divider
(P5)
Divider
(P5)
Shelf Panel
(P2)
Left
Side Panel
(P3)
Left
Side Panel
(P3)
Right
Side Panel
(P4)
Right
Side Panel
(P4)
Parts list
Top Panel (P1);
2 x Shelf Panel (P2);
2 x Left Side Panel (P3);
2 x Right Side Panel (P4);
4 x Divider (P5);
16 x Dowels
(H1)
24 x Cam Bolts
(H2)
24 x Cam Nuts
(H3)
8 x Plastic Glides
(H4)
1 x Support Leg
(H5)
1 x Screw
(H6)

You will need
Step 2
Phillips Head
Screwdriver
16 x Cam Bolts
(H2)
Attach 8 x Cam Bolts (H2) into Left Side Panel (P3) and Right Side Panel (P4)
using a Phillips head screwdriver.
Repeat Step 2 for another Left Side Panel (P3) and Right Side Panel (P4).
You will need
Step 1
Phillips Head
Screwdriver
fantasticfurniture.com.au Page 5
8 x Cam Bolts
(H2)
(P1)
H2 H2
H2
H2
H2
H2
H2
H2
Attach 8 x Cam Bolts (H2) into Top Panel (P1). Tighten Cam Bolts using
a Phillips head screwdriver.
(P4) x 2
(P3) x 2
H2
H2
H2
H2
H2
H2
H2
H2

This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Step 4
You will need
4 x Dowels
(H1)
Step 3
You will need
4 x Cam Nuts
(H3)
Phillips Head
Screwdriver
Insert 4 x Cam Nuts (H3) into the holes of Shelf Panel (P2) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Side Panels (P3, P4) to Shelf Panel (P2),
then tighten the cam nuts using a Phillips head screwdriver.
Insert 4 x Dowels (H1) into Side Panels (P3, P4).
Put Dividers (P5) to the place as shown.
H1 H1
H1 H1
(P4)
(P3)
(P5)
(P5)
fantasticfurniture.com.au
fantasticfurniture.com.au Page 6
H3
H3
(P4)
(P3)
(P2)
H3
H3

8 x Dowels
(H1)
8 x Cam Nuts
(H3)
Phillips Head
Screwdriver
You will need
Step 5
Hammer 8 x Plastic Glides (H4) on to end of Shelf Panels (P3, P4).
Attach 1 x Support Leg (H5) to the bottom of Shelf Panel (P2) with 1 x Screw (H6).
H1
H3
H3 H3
H3
H1
H1 H1 H1
(P4)
(P3)
(P2)
(P5)
(P5)
Insert 4 x Cam Nuts (H3) into the holes of Shelf Panel (P2) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Side Panels (P3, P4) to Shelf Panel (P2),
then tighten the cam nuts using a Flat head screwdriver.
1 x Support Leg
(H5)
1 x Screw
(H6)
8 x Plastic
Glides (H4)
fantasticfurniture.com.au
You will need
Step 6
Phillips Head
Screwdriver
Hammer
(P4)
(P4)
(P3)
(P3)
H4 H4
H4 H4
H4 H4 H5
H6
H4 H4

Insert 8 x Cam Nuts (H3) into the holes of Side Panels (P3, P4). Rotate the cam nuts so the
arrows point towards the incoming cam bolts. Attach Top Panel (P1) and tighten the cam
nuts using a Flat head screwdriver.
You will need
Step 7
8 x Cam Nuts
(H3)
Phillips Head
Screwdriver
Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
fantasticfurniture.com.au Page 8
H3
H3
(P1)
(P4)
(P4)