fantastic furniture NIVA Bookcase 1 Drawer User manual

Version 1.0
NIVA
Bookcase 1 Drawer
fantasticfurniture.com.au
Required
Two People

fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
Page 2
Love it? Share it!
Fantastic buy! Share how it looks at home for your
chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
Warning: Ensure the wall strap is attached
to avoid serious injury
To avoid any serious of fatal injury, a wall strap has been provided with
this product to prevent toppling. We strongly recommend that this
product is permanently fixed to the wall or other suitable surface. Fixing
of what fixing device to use.
Weight capacity: 30kgs/shelf

Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
!If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
!Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au Page 3

fantasticfurniture.com.au
Page 4
What you need
to assemble the product
Other tools you need
Phillips head screwdriver; Hammer
Part list
Box 1: Top Panel (P1);
Bottom Panel (P4);
4 x Legs (P5);
2 x Short Rails (P6);
2 x Shelves (P8);
Drawer Left Side (P9);
Drawer Right Side (P10);
Drawer Base (P12);
Drawer Rail (P14);
Hardware pack.
Box 2: Left Side Panel (P2);
Right Side Panel (P3);
2 x Long Rails (P7); Shelf (P8);
Bottom Shelf (P16);
Drawer Front (P13);
Drawer Back (P11)
Back Panel (P15);
Metal Rail (P17).
Top Panel (P1)
Back Panel
(P15)
Shelf (P8)
Shelf (P8)
Shelf (P8)
Bottom Shelf (P16)
Left Side Panel
(P2)
Right Side Panel
(P3)
Metal Rail
(P17)
Drawer Rail
(P14)
Drawer Base
(P12)
Drawer Front
(P13)
Drawer
Left Side
(P9)
Drawer
Right Side
(P10)
Drawer Back (P11)
Bottom Panel (P4)
Leg
(P5)
(P5)
(P5)
(P5)
Short Rail
(P6)
(P6)
Long Rail (P7)
(P7)

fantasticfurniture.com.au
Page 5
Hardware Pack
48 x Cam Bolts
(H1)
42 x Large Cam
Nuts (H2)
36 x Dowels
(H3)
6 x Small Cam
Nuts (H4)
4 x Screws
(H5)
36 x Nails
(H6)
4 x Felt Pads
(H7)
12 x Screws
(H8)
1 x Left Runner
Tracks (H9)
1 x Left Runner
(H10)
1 x Right Runner
Tracks (H11)
1 x Right Runner
(H12)
2 x Screws
(H13)
4 x Screws
(H19)
2 x Wall Straps
(H14)
4 x Flat Washers
(H15)
4 x Screw Caps
(H16)
6 x Screws
(H17)
3 x Screws
(H18)

Step 1
Page 6fantasticfurniture.com.au
You will need
10 x Cam Bolts
(H1)
Secure 10 x Cam Bolts (H1) to Bottom Panel (P4) as shown by tightening
with the Phillips Head Screwdriver.
Step 2
Phillips head
screwdriver
You will need
12 x Dowels
(H3)
Insert 4 x Dowels (H3) into Short Rails (P6x2) and 8 x Dowels (H3)
into Long Rails (P7x2) as shown.
(P4)
H1
H1
1H1H1H
H1
H1
H1 H1
H1
H1
H1
H1
(P7)
(P6)
(P6)
(P7)
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3

Step 3
Page 7fantasticfurniture.com.au
You will need
8 x Cam Bolts
(H1)
Secure 2 x Cam Bolts (H1) to Leg (P5) as shown by tightening with the Phillips Head Screwdriver.
the bottom of Leg (P5).
Repeat steps for the remaining Legs (P5x3).
Step 4
Phillips head
screwdriver
You will need
4 x Large Cam
Nuts (H2)
Insert 2 x Large Cam Nuts (H2) into Short Rail (P6) and rotate
so that the arrows point towards the incoming Cam Bolts.
Secure Legs (P5x2) to each end of the Short Rail (P6) by tightening the Cam Nuts
with the Phillips Head Screwdriver.
Repeat steps for the second set of Legs (P5x2) and Short Rail (P6).
4 x Felt Pads
(H7)
(P5)
H1
H1
H7
X4
H2
(P5)
(P5)
(P5)
(P5)
(P6) (P6)
H2
H2
H2
Phillips head
screwdriver

Step 5
Page 8fantasticfurniture.com.au
You will need
Insert 4 x Large Cam Nuts (H2) into Long Rails (P7x2) and rotate so that the arrows point
towards the incoming Cam Bolts.
Attach Legs (P5x4) to Long Rails (P7x2) by tightening the Cam Nuts
with the Phillips Head Screwdriver.
Step 6
You will need
10 x Large Cam
Nuts (H2)
Insert 10 x Large Cam Nuts (H2) into Short & Long Rails (P6x2,P7x2) as shown and rotate
so that the arrows point towards the incoming Cam Bolts.
Attach Short & Long Rails (P6x2,P7x2) to Bottom Panel (P4) by tightening the Cam Nuts
with the Phillips Head Screwdriver.
4 x Large Cam
Nuts (H2)
(P7)
(P7)
(P4)
(P6)
(P6)
H2
H2
H2
Phillips head
screwdriver
H2
H2
(P5)
(P5)
(P5)
(P5)
(P7)
(P7)
Phillips head
screwdriver

Step 7
Page 9fantasticfurniture.com.au
You will need
Secure 4 x Cam Bolts (H1) and 4 x Screws (H5) to Bottom Panel (P4) as shown
by tightening with the Phillips Head Screwdriver.
Step 8
You will need
16 x Dowels
(H3)
Insert 4 x Dowels (H3) into each Shelf (P8x3) and Bottom Shelf (P16) as shown.
Attach Metal Rail (P17) to Bottom Shelf (P16) with 3 x Screws (H18) by tightening
with the Phillips Head Screwdriver.
4 x Screws
(H5)
4 x Cam Bolts
(H1)
(P4)
Phillips head
screwdriver
Phillips head
screwdriver
H1
H1
H1
H1
H5
H5
H5
H5
3 x Screws
(H18)
(P8)
H18 H3
H3
H3
H3
H3
H3
H3
H3
H18
H18
(P16)
(P17)
X3

Step 9
Page 10fantasticfurniture.com.au
You will need
Insert 4 x Dowels (H3) into Left Side Panel (P2) as shown.
Secure 8 x Cam Bolts (H1) to Left Side Panel (P2) by tightening
with the Phillips Head Screwdriver.
Attach Left Runner Track (H9) to Left Side Panel (P2) with 3 x Screws (H8)
by tightening with the Phillips Head Screwdriver.
Step 10
You will need
4 x Dowels
(H3)
Insert 4 x Dowels (H3) into Right Side Panel (P3) as shown. Secure 8 x Cam Bolts (H1)
to Right Side Panel (P3) by tightening with the Phillips Head Screwdriver.
Attach Right Runner Track (H11) to Right Side Panel (P3) with 3 x Screws (H8)
by tightening with the Phillips Head Screwdriver.
8 x Cam Bolts
(H1)
Phillips head
screwdriver
(P3)
3 x Screws
(H8)
1 x Left Runner
Track (H9)
4 x Dowels
(H3)
8 x Cam Bolts
(H1)
Phillips head
screwdriver
3 x Screws
(H8)
1 x Right Runner
Track (H11)
H8H8H8
H11 H1
H3
H3
H3
H3
H11
H8
H1
H1
H1
H1
H1
H1
H1
H8
H8
Laminated
Edge
Laminated
Edge
H3
H8
H9
H3
H3
H3
H1
H1
H1
H1
H1
H1 H1
H1
H8
H8
(P2)
H9
H8 H8 H8