fantastic furniture Lunar Tallboy User manual

fantasticfurniture.com.au
Lunar
Tallboy 5 Drawer
Version 1.0

Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
fantasticfurniture.com.au
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.use

fantasticfurniture.com.au Page 3
Read through the instructions
carefully before you begin.
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screwsuntil the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a so t surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
components please visit our website Help Centre for further assistance.
!Please see page 2for any safety requirements or weight restrictions.
Useful information
Assembly checklist

2 x Washers
P13
Page 4
fantasticfurniture.com.au
What you need
to assemble the product
Hardware Pack :
(H2) (H3) (H4)
( H15)
(H1) (H5)
45 x Cam Nuts
45 x Cam Bolts
(H6) (H7)
22 x Dowels
(H8) Tracks
(H9)
Tracks
(H11)
(H12) 60 x Runner Screws 32 x Drawer Screws
(H13) (H14)
Other tools you need
Phillips Head screwdriver;Hammer
5 x CL Runner 5 x DL Runners
(H10)
5 x CR Runner 5 x DR Runners
P1
P2
P3
P4
P5
P6
P7
P12
4 x Handles 4 x Feet Glides 14 x Wedges 14 x Wedge Screws
10 x Handle Screws
P6
P6
P6
P8
P9
P11
P12
P13
P15
P14
P10
P6
P6
Box 1:
Top Panel (P1);
Support Panel (P2);
Left Side Panel (P3);
Right Side Panel (P4);
Base Panel (P5);
Back Panel (P7);
Box 2:
6 x Support Panels (P6);
5 x Drawer Back Panels (P8);
5 x Drawer Side Panels (L) (P9);
5 x Drawer Side Panels (R) (P10);
5 x Drawer Base Panels (P11);
2 x Drawer Front Panels (P12);
2 x Drawer Front Panels (P13);
5 x Drawer Support Panels (P14);
Drawer Front Panel (P15);
(H16)
Handle

Page 5
Attach 5 x CL Runner Tracks (H9) to the Left Side Panel (P3) with 15 x Runner Screws (H13), by
tightening with a Phillips Head Screwdriver.
Repeat process to attach 5 x CR Runner Tracks (H11) to the Right Side Panel (P4).
Step 1
(P3)
(P4)
(H9)
(H11)
(H9)
(H11)
You will need
5 x CL Runner
Tracks (H9)
(H13)
Phillips Head
Screwdriver
5 x CR Runner
Tracks (H11)
30 x Runner
Screws (H9)
(H9)
(H11)
(H11)
(H9)
(H11)
(H13)
(H13)
Insert 16 x Cam Bolts (H6) into the Left Side Panel (P3) and Right Side Panel (P4), by
tightening with a Phillips Head Screwdriver.
Insert 16 x Dowels (H7) into the Left Side Panel (P4) and Right Side Panel (P4).
Insert 4 x Feet Glides (H2) on to the underside of the legs by gently using a Hammer as
shown.
fantasticfurniture.com.aufantasticfurniture.com.au
Step 2
P3
P4
(H6)
(H6)
(H6)
(H6)
(H6)
(H7)
(H7)
(H7) (H7)
(H7)
(H7)
You will need
Phillips Head
Screwdriver
(H7)
16 x Dowels
(H6)
16 x Cam Bolts
(H6)
(H6)
(H6)
(H6)
(H6)
(H6)
(H6)
(H6)
(H7)
(H7)
(H7)
(H7)
(H7)
(H7)
(H7)
(H7)
(H6)
(H6)
(H6)
(H6)
(H2)
4 x Feet Glides
(H2)
(H2)
(H2)
(H2)
Hammer

Page 6
fantasticfurniture.com.au
Step 4
You will need
Step 3
Phillips Head
Screwdriver
(H7)
2 x Dowels
(P1)
(P2)
(H14)
(H14)
(H7)
(H7)
(H6)
You will need
Phillips Head
Screwdriver
(H7)
4 x Dowels
(H6)
4 x Cam Bolts
(H7)
(H6)
(H6)
(H6)
(H6)
(P1)
(H7)
(H7)
(H7)
2 x Drawer
Screws (H14)
Attach Support Panel (P2) to the Top Panel (P1) with 2 x Dowels (H7) and 2 x Drawer Screws (H14),
by tightening with the Phillips Head Screwdriver.by
Insert 4 x Dowels (H7) into the Top Panel (P1).
Insert 4 x Cam Bolts (H6) into the Top Panel (P1), by tightening with a Phillips Head Screwdriver.

Page 7
Step 5
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
Phillips Head
Screwdriver
(P3)
You will need
(H5)
8 x Cam Nuts
(P5)
(P6)
(P6)
(P6)
(P6)
(P6)
(P6)
(H5)
(H5)
(H5)
(H5)
(H5)
Insert 8 x Cam Nuts (H5) into the 6 x Support Panels (P6) and Base Panel (P5) as shown.
Attach 6 x Support Panels and Base Panel (P5) to the Left Side Panel (P3), by tightening all
Cam Nuts with the Phillips Head Screwdriver.
Step 6
(P4)
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
Phillips Head
Screwdriver
You will need
(H5)
8 x Cam Nuts
P5
(H5)
(H5)
(H5)
(H5)
(P6)
(P6)
(P6)
(P6)
fantasticfurniture.com.au
Insert 8 x Cam Nuts (H5) into the 6 x Support Rails (P6) and Base Panel (P5) as shown.
Attach Right Side Panel (P4) to the Support Panels (P6) and Base Panel (P5), by tightening
all Cam Nuts with the Phillips Head Screwdriver.

Page 8
Step 7
fantasticfurniture.com.au
(P7)
(P3)
(P4)
(P5)
Slot the Back Panel (P7) into the grooves of panels (P3, P4 & P5) as shown.
Raw side facing inside
Step 8
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
(P1)
(P3)
(P4)
Phillips Head
Screwdriver
You will need
(H5)
4 x Cam Nuts
(H5)
Insert 4 x Cam Nuts into Left Side Panel (P3) and Right Side Panel (P4).
Attach the Top Panel (P1) to the Left Side Panel (P3) and Right Side Panel (P4) by aligning the
Dowels (H7) and Cam Bolts (H6) to the holes as shown.
Ensure that the Back Panel (P7) is slotted into the groove of the Top Panel (P1) as well.
Tighten the Cam Nuts (H5) with the Phillips Head Screwdriver in the Left Side Panel (P3) and
Right Side Panel (P4) to lock into position.

Page 9
Step 9
You will need
Phillps Head
Screwdriver
(H3) x 14
(H4) x 14
(P7)
(H3)
14 x Wedges 14 x Wedge
Screws (H4)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H4)
(H4)
(H4)
(H4)
(H4)
(H4)
(H4)
(H4)
(H4)
(H4)
(H4)
(H4)
fantasticfurniture.com.au
Secure Back Panel (P7) in place with 14 x Wedges (H3) using 14 x Wedge Screws (H16) by
tightening with the Phillips Head Screwdriver.
Step 10
(H6)
(H6)
(H6)
(H6)
(H6)
(H8)
(P15)
(H6) (P12)x 2
(H6)
(P13)x 2
(H8)
(H6)
(H6)
(H6)
Insert 25 x Cam Bolts (H6) into the Drawer Front Panels (P12, P13 & P15), by tightening with
a Phillips Head Screwdriver.
You will need
Phillips Head
Screwdriver
(H6)
25x Cam Bolts

Page10
fantasticfurniture.com.au
Insert 5 x Cam Nuts into the Drawer Side Panels (P9 & P10) and Drawer Support Panels (P14).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach the Drawer Front Panels (P12, P13 & P15) to the Drawer Side Panels (P9 & P10), by tightening
Cam Nuts with the Phillips Head Screwdriver.
Repeat for the remaining drawers.
Step 11
(H5)
(H5)
(P9)x 4
(P10)x 4
(H5)
(P14)x 4
(P12) x 2
(P13) x 2
(P15)
Phillips Head
Screwdriver
You will need
25x Cam
Nuts (H5)
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
Step 12
Slot in the Drawer Base Panel (P11) into the grooves of panels (P9 & P10) and Drawer
Front Panels (P12, P13 & P15) as shown.
(P11)x 5
(P9)
(P10)
(P14)
Raw side facing bottom
(P12) x 2
(P13) x 2
(P15)