fantastic furniture Jervis Single Bed User manual

Jervis
Single Bed
fantasticfurniture.com.au
Version 1.0

fantasticfurniture.com.au Page 2Page 2
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!

Assembly checklist
Useful information
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Please see page 2 for any safety requirements or weight restrictions.
Page 3
fantasticfurniture.com.au

Footboard (P2) ; 2 x Side Rail (P3) ; Cross Rail (P4) ; 2 x Footboard Leg (P5) ;
Headboard (P1) ; Slats (P7)
(H2)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Parts list
Headboard
(P1)
Box 1 :
End Connectors (P6) ; Hardware Box
Box 2 :
Side Rail
(P3)
Side Rail
(P3)
Cross Rail
(P4) Footboard
(P2)
Footboard Leg
(P5)
26 x End Connectors (P6)
13 x Slats (P7)
Hardware pack
(H1)
4 x 18mm Bolt 1 x Allen Key (H3)
2 x 90mm Bolt 12 x Washer (H4)
(H5) (H6) (H7) (H8)
8 x 20mm Bolt 2 x Nut 2 x 32mm Screw 2 x Brackets
1 x Spanner (H9)
fantasticfurniture.com.au Page 4

Attach the footboard leg (P5) to the bracket (H8) by using 1 x bolt (H3), 2 x washers (H4)
Phillips head
1 x Spanner
(H6)
2 x Nuts
and 1 x nut (H6), tighten with the spanner (H9) and screwdriver.
(H4)
(H6)
Step 1
You will need
4 x Washers
(H4)
4 x Bolts 20mm
(H5)
2 x Brackets
(H8)
Phillips head
Screwdriver
P2
(H8) (H4) (H5)
Attach 2 x brackets (H8) to the footboard (P2) with 4 x washers (H4) and 4 x bolts 20mm
(H5). Do not fully tighten the bolts until step 6.
2 x Bolts 90mm
(H3)
You will need
4 x Washers
(H4)
Step 2
fantasticfurniture.com.au Page 5
screwdriver
(H9)
P2
(H9)
(H9)
(H8)
(P5)
(H4)
(H3)
Repeat for the other leg.

(H2)
4 x Bolts 18mm
(H1)
Phillips head
(P3) to the headboard (P1) over the bolt as shown. Do not fully tighten until step 6.
Loosen the bolts by 8mm using the allen key (H2) as shown. Then attach the side rails
Attach the brackets (H8) to the side rails (P3) as shown with 4 x
8mm
You will need
Step 3
P1
P1
P1
P3 P3
P3
(H1)
P3
(H2)
1 x Allen Key
Step 4
You will need
4 x Washers
(H4)
4 x Bolts 20mm
(H5) Screwdriver
P1
P3
P3
P2
P2 P3
(H5) (H4)
washers (H4) and 4 x 20mm bolts (H5). Do not fully tighten the bolts until step 6.
fantasticfurniture.com.au Page 6

Step 5 (a)
You will need
26 x End 13 x Slats (P7)
Connectors (P6)
Insert the slat (P7) into the end connectors (P6).
Lower the slat (P7) with the end connectors (P6) to the side rails (P3). Ensure the
connectors are in place over the side rail holes and apply downward pressure on
the slat (P7) with the end connectors (P6) until the end plastic cap is fully
fantasticfurniture.com.au Page 7
inserted into the rail.
Repeat step 5a to 5b for the remainder of the slats.
Step 5 (b)

Step 5 (c)
Step 6
You will need
2 x Screws
(H7)
Phillips head
Screwdriver
(H7)
You can use either
attach cross rail (P4)
pre-drilled hole to
Fully tighten all the bolts on the brackets. Attach the cross rail (P4) to the side
rails (P3) with the 2 x screws (H7) and tighten with a phillips head screwdriver.
fantasticfurniture.com.au Page 8

Step 7
fantasticfurniture.com.au Page 9
Job complete!
In the interest of our environment please dispose
of all packaging thoughtfully.