fantastic furniture NIVA Desk 1 Drawer User manual

Version 1.1
Hayden
fantasticfurniture.com.au
Desk 1 Drawer

Secure it!
Wall attachment guide
(with available wood stud)
Screw directly into
stud.
Please seek professional advice if you are in doubt of what fixing device to use.
•
•
• Do not
•
•
Reduce the risk of furniture
tip-over accidents
(with available wood stud)
S
.
Screw
fantasticfurniture.com.aufantasticfurniture.com.au
Recommended Weight Capacity :60kg

fantasticfurniture.com.au Page 3
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 4
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Hardware Pack
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
DO NOT USE
Page 5
fantasticfurniture.com.au
Top Panel
(P1)
Right Side
Panel
(P3)
Left Side
Panel
(P2)
Back Panel
(P5)
Rail
(P6)
Support
Rail
(P4)
Left
Drawer Side
(P12)
Right
Drawer Side
(P13)
Drawer Back
(P15) Drawer
Base
(P14)
Drawer
Support
(P16) Drawer Front
(P11)
Leg
(P7)
Leg
(P8)
Leg
(P9)
Leg
(P10)
Parts list
Top Panel (P1);
Left Side Panel (P2);
Right Side Panel (P3);
Support Rail (P4);
Back Panel (P5); Rail (P6);
Leg (P7); Leg (P8);
Leg (P9); Leg (P10);
Drawer Front (P11);
Left Drawer Side (P12);
Right Drawer Side (P13);
Drawer Base (P14);
Drawer Back (P15);
Drawer Support (P16);
19 x Cam Bolts
(H3)
2 x Sleeve
Nuts
(H2)
2 x Bolts
(H1)
19 x Cam Nuts
(H4)
14 x Small
Screws
(H5)
2 x Runners
(H6)
6 x Long
Screws
(H7)
4 x Felt Pads
(H9)
2 x Long Round
Screws
(H8)
1 x Screw
(H11)
1 x Safety
Strap
(H10)
2 x Washers
(H12)
8 x Bolts
(H13)

You will need
Step 1
You will need
Step 2
Page 6
fantasticfurniture.com.au
(P7)
(P8)
(P9)
(P10)
H1
H2
H1
H2
H3
H3
H3
H3
Attach leg (P7) to leg (P8) and leg (P9) to leg (P10) with 2 x bolts (H1) and 2 x sleeve nuts (H2) .
Attach 4 x cam bolts (H3) into the holes of legs (P8, P9).Tighten with a Phillips head screwdriver.
Phillips head
screwdriver
2 x Sleeve
Nuts (H2)
2 x Bolts
(H1)
4 x Cam Bolts
(H3)
Slide Track
(H6-1)
Slide Runner
(H6-2)
H6
2 x Runners
(H6)
Separate the 2 sets of slide runners (H6-1) and slide tracks (H6-2)
from runners (H6) by following the steps below:
Extend the slide runner all the way forward.
Press the plastic release lever of the slide up
and pull the slide runner (H6-2) completely out.

You will need
Step 3
Page 7
fantasticfurniture.com.au
You will need
Step 4
H6-1
H5 H5 H5
H6-1
H5 H5 H5
(P2) (P3)
H5
H5
H5
H5
H6-1
H6-1
H5
H5
H3 H3
H3
H3
2 x Slide Tracks
(H6-1)
6 x Small
Screws (H5)
Phillips head
screwdriver
4 x Cam Bolts
(H3)
Attach 2 x the separated slide tracks (H6-1) to side panels (P2, P3) with 6 x small screws (H5) as
shown.Insert 4 x cam bolts (H3) into the holes of side panels (P2, P3).Tighten with a Phillips head
screwdriver.
(P3)
(P5)
(P4)
Insert 2 x cam nuts (H4) into the holes of back panel (P5).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach back panel (P5) to right side panel (P3),by sliding cam bolts and cam nuts into place.
Tighten the cam nuts using a flat Phillips screwdriver.
Attach support rail (P4) to right side panel (P3) with 2 x small screws (H5).
H4
H4
H5
H5
2 x Cam Nuts
(H4)
Phillips head
screwdriver
2 x Small
Screws (H5)
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.

You will need
Step 6
You will need
Step 5
Page 8
fantasticfurniture.com.au
Insert 2 x cam nuts (H4) into the holes of back panel (P5).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach left side panel (P2) into place,by sliding cam bolts and cam nuts into place.
Tighten the cam nuts using a Phillips head screwdriver.
Attach support rail (P4) to left side panel (P2) with 2 x small screws (H5).
(P2)
(P5)
(P4)
H4
H4
H5
H5
2 x Cam Nuts
(H4)
Phillips head
screwdriver
2 x Small
Screws (H5)
(P9)
(P3)
(P10)
H13
H13
H13
Attach legs (P9, P10) to right side panel (P3)
with 4 x bolts (H13) using a Phillips head screwdriver.
Phillips head
screwdriver
4 x Bolts
(H13)

Step 8
You will need
You will need
Step 7
Page 9
fantasticfurniture.com.au
Phillips head
screwdriver
Phillips head
screwdriver
(P9)
(P6)
H4
H4
2 x Cam Nuts
(H4)
Insert 2 x cam nuts (H4) into the holes of rail (P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach rail (P6) to leg (P10),by sliding cam bolts and cam nuts into place.
Tighten the cam nuts using a Phillips head screwdriver.
(P7)
(P8)
(P6)
(P2)
H1
H4
H4
2 x Cam Nuts
(H4)
Insert 2 x cam nuts (H4) into the holes of rail (P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach leg (P8) to rail (P6),by sliding cam bolts and cam nuts into place.
Tighten the cam nuts using a Phillips head screwdriver.

Page 10
fantasticfurniture.com.au
Step 9
You will need
H13
H13
H13
H13
(P7)
(P8)
(P2)
Attach legs (P7, P8) to left side panel (P2) with 4 x bolts (H13) using a Phillips head screwdriver.
4 x Bolts
(H13)
Phillips head
screwdriver
(P1)
H3
H3
H3
H3
H3
H3
6 x Cam Bolts
(H3)
Phillips head
screwdriver
You will need
Step 10
Insert 6 x cam bolts (H3) into the holes of top panel (P1) as shown.
Tighten with a Phillips head screwdriver.