fantastic furniture HAMILTON Desk 3 Drawer User manual

Version 1.0
HAMILTON
Desk 3 Drawer
fantasticfurniture.com.au

fantasticfurniture.com.au PAGE 2
Looks like you’ve found
your Fantastic!
Love it? Share it!
Fantastic buy! Share how it looks at home for your
chance to win a $250 Fantastic Furniture Gift Card!
fantasticfurniture
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
Recommended weight capacity : 60kg on top.

PAGE 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Left Side Panel (P2);
Right Side Panel (P3);
Divider (P4);
2 x Rails (P5); Rail (P6);
Rail (P7); Rail(P8);
Back Panel (P9);
Back Panel (P10);
2 x Drawer Front (P11);
2 x Left Drawer Side (P12);
2 x Right Drawer Side (P13);
3 x Drawer Base (P14);
2 x Drawer Back (P15);
Drawer Front (P16);
Left Drawer Side (P17);
Right Drawer Side (P18);
Drawer Back (P19)
Hardware pack
Left Drawer
Side (P12) Left Drawer
Side (P17)
Right Drawer
Side (P13)
Right Drawer
Side (P18)
Drawer Back
(P15) Drawer Back
(P19)
Drawer
Base
(P14)
Drawer
Base
(P14)
Drawer
Front
(P11)
Drawer
Front
(P16)
Top Panel
(P1)
Right Side
Panel
(P3)
Left Side
Panel (P2)
Divider
(P4)
Back Panel
(P9)
Back Panel
(P10)
Rail
(P5)
Rail
(P5)
Rail
(P8)
Rail
(P6)
Rail
(P7)
32 x Cam
Bolts
(H3)
32 x Cam
Nuts
(H4)
12 x Dowels
(H1)
30 x Small
Screws
(H5)
3 x CL Runner
Tracks
(H6)
3 x CR Runner
Tracks
(H7)
3 x DR Runners
(H9)
3 x Handle Bolt
(H10)
3 x Handle
(H11)
3 x DL Runners
(H8)
15 x Long
Screws
(H2)
8 x Wedges
(H12)
8 x Wedge
Screws
(H13)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
PAGE 4
fantasticfurniture.com.au
DO NOT USE
x2
6 x Plastic
Glides
(H14)

(P2)
(P3)
You will need
Step 1
H7
CR
H5
Step 2
You will need
Phillips Head
Screwdriver
Phillips Head
Screwdriver
H3
H3
H3
H3
H3
H3
H5
H7
3 x Cam Bolts
(H3)
5 x Cam Bolts
(H3)
Attach 5 x Cam Bolts (H3) to Left Side Panel (P2) by tightening with the Phillips Head
Screwdriver. Secure 2 x Plastic Glides (H14) to the bottom of Left Side Panel (P2) with the
Hammer.
Attach 3 x Cam Bolts (H3) and 3 x CR Runner Tracks (H7) to Right Side Panel (P3)
with 9 x Small Screws (H5) by tightening with the Phillips Head Screwdriver. Secure 2 x
Plastic Glides (H14) to the bottom of Right Side Panel (P3) with the Hammer.
fantasticfurniture.com.au PAGE 5
H5
H7 H5
H7
3 x CR Runner
Tracks (H7)
9 x Small
Screws (H5)
H14
H14
2 x Plastic
Glides (H14) Hammer
2 x Plastic
Glides (H14)
Hammer H14
H14

You will need
Step 3
Step 4
You will need
Attach 2 x Cam Bolts (H3) and 3 x CL Runner Tracks (H6) to Divider (P4) with 9 x Small
Screws (H5) by tightening with the Phillips Head Screwdriver. Flip the Divider (P4) over, and
attach 4 x Cam Bolts (H3) to Divider (P4) by tightening with the Phillips Head Screwdriver.
Secure 2 x Plastic Glides (H14) to the bottom of Divider Panel (P4) with the Hammer.
Attach 6 x Cam Bolts (H3) to Top Panel (P1) by tightening with the
Phillips Head Screwdriver.
Phillips Head
Screwdriver
Phillips Head
Screwdriver
6 x Cam Bolts
(H3)
9 x Small
Screws (H5)
6 x Cam Bolts
(H3)
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H5 H6
fantasticfurniture.com.au
fantasticfurniture.com.au PAGE 6
H5 H6
H5 H6
FLIP
3 x CL Runner
Tracks (H6)
H6
CL
H5
(P4)
(P4)
(P1)
2 x Plastic
Glides (H14)
Hammer
H14
H14

Insert 1 x Dowel (H1) into Rail (P8) and 5 x Cam Nuts (H4) into
Rails (P5x2 & P8) as shown. Rotate the cam nuts so the arrow points towards the incoming cam
bolts. Attach Rails (P5x2 & P8) to Left Side Panel (P2) by tightening all Cam Nuts with the Phillips
Head Screwdriver.
Slide Back Panel (P9) into the grooves of Rails (P5x2).
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Step 6
You will need
Phillips Head
Screwdriver
1 x Dowels
(H1)
Step 5
5 x Cam Nuts
(H4)
H1
H4
H4
H4
fantasticfurniture.com.au PAGE 7
(P2)
(P8) (P5)
(P5)
(P5)
(P5)
(P9)
Countersink
face bottom

You will need
Phillips Head
Screwdriver
Step 7
Insert 4 x Cam Nuts (H4) into Rails (P5x2) as shown. Rotate the cam nuts so the arrows point
towards the incoming cam bolts. Attach Rails (P5x2) to Divider (P4) by tightening all cam nuts
with the Phillips Head Screwdriver.
Insert 2x Dowels (H1) into Divider (P4).
Insert 2 x Cam Nuts (H4) into Rails
(P6&P7) as shown. Rotate the cam
nuts so the arrows point towards the
incoming cam bolts. Attach
Rails (P6&P7) to Divider (P4) by tightening all cam nuts with the Phillips
Head Screwdriver.
You will need
Phillips Head
Screwdriver
Step 8
2 x Dowels
(H1)
4 x Cam Nuts
(H4)
2 x Cam Nuts
(H4)
H4
fantasticfurniture.com.au PAGE 8
(P5)
(P4)
(P6)
(P4)
(P7)
(P5)
H1
H4
H4
H1

(P3)
(P10)
(P3)
(P4)
(P7)
(P6)
(P8)
You will need
Step 10
Step 9
Gently stand the unit upright.
Slide Back Panel (P10) into the grooves of Divider & Right Side Panel (P4&P3).
3 x Dowels
(H1)
3 x Cam Nuts
(H4)
(P4)
Insert 3x Dowels (H1) into
Right Side Panel (P3). Insert 3 x Cam
Nuts (H4) into Rails (P6&P7&P8) as shown. Rotate the cam nuts so the arrows point towards the
incoming cam bolts. Attach Rails Rails (P6&P7&P8) to Right Side Panel (P3) by tightening all cam
nuts with the Phillips Head Screwdriver.
fantasticfurniture.com.au PAGE 9
Phillips Head
Screwdriver
H1
H1
H4
H1
H4

You will need
Step 11
Insert 6 x Dowels (H1) and 6 x Cam Nuts (H4) into Divider & Right & Left Side Panels (P4&P2&P3)
as shown. Rotate the cam nuts so the arrows point towards the incoming cam bolts. Attach Top
Panel (P1) to unit by tightening cam nuts with the Phillips Head Screwdriver. Secure Top Panel (P1)
to Rail (P8) with 3 x Long Screws (H2) by tightening with the Phillips Head Screwdriver.
Attach 12 x Cam Bolts (H3) to Drawer Fronts (P11x2&P16) by tightening with the
Phillips Head Screwdriver.
H1
H1
H4
H4
H2
H3
H3
H3
H3
H3
H3
H3
H3
H2
H2
H4
H4
H1
H1
6 x Cam Nuts
(H4)
Phillips Head
Screwdriver
Phillips Head
Screwdriver
You will need
Step 12
6 x Dowels
(H1)
(P1)
(P2)
(P16)
(P11) x2
(P4)
(P8) (P3)
12 x Cam Bolts
(H3)
fantasticfurniture.com.au PAGE 10
3 x Long
Screws (H2)