fantastic furniture ZAYNE User manual

Version 1.0
ZAYNE
www.fantasticfurniture.com.au
REQUIRED
TWO PEOPLE
Utility 4 Shelf 2 Door Oak White

www.fantasticfurniture.com.au PAGE 2
Enjoy
Your purchase from
Australia’s Best Value Furniture Store
Recommended weight capacity : 15kgs/shelf.
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied with a
wall strap to prevent toppling. We strongly recommend that this product is
permanently fixed to the wall or other suitable surface. Connecting
attachments for your wall are not included since different surface materials
require different attachments. Please seek professional advice if you are in
doubt of what wall connections to use.

Assembly checklist
Useful Information
www.fantasticfurniture.com.au PAGE 3
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Please see page 2 for any safety requirements or weight restrictions.

Parts list
www.fantasticfurniture.com.au PAGE 4
What you need
to assemble the product
Additional Tools Required
Phillips head screwdriver;
DO NOT USE
Hardware pack
Top Panel
(P1)
Back Panel
(P6)
Door
(P9)
Left Side
Panel
(P3)
Right Side
Panel
(P4)
Back Panel
(P6)
Shelf Panel
(P5)
Bottom Panel
(P2)
Divider
Panel
(P7)
Divider
Panel
(P7)
Door
(P8)
Top Panel (P1);
Bottom Panel (P2);
Left Side Panel (P3);
Right Side Panel (P4);
Shelf Panel (P5);
2 x B
2 x ack Panel (P6); Divider (P7);
Door(P8); Door (P9)
12 x Cam Bolts
(H3)
8 x Large
Screws
(H2)
16 x Dowels
(H1) 12 x Cam Nuts
(H4) 8 x Roller
Screws
(H5)
4 x Rollers
(H6) 4 x Metal
Rods
(H7)
8 x Wedges
(H8) 18 x Back Screws
(H9)
2 x Brackets
(H10) 1 x Safety
Strap Screw Dowels
(H12)
1 x Safety
Strap
(H11)
2 x Washers
(H13) 4 x Felt Pads 2 x Long
(H14)
(H15)

PAGE 5
You will need
Step 1
www.fantasticfurniture.com.au
You will need
Phillips head
screwdriver
Step 2
Insert 2 x Cam Bolts (H3) into Left Side panel (P3) and 2 x Cam Bolts (H3) into Right Side panel (P4).
Secure by tightening Cam Bolts (H3) with a Phillips Head Screwdriver.
Insert 2 x Cam Bolts (H3) into Shelf panel (P5) and secure by tightening Cam Bolts (H3)
with a Phillips Head Screwdriver.
H3
H3
H3
H3
4 x Cam Bolts
(H3)
H3
H3
Phillips head
screwdriver
2 x Cam Bolts
(H3)
(P3)
(P4)
(P5)

www.fantasticfurniture.com.au PAGE 6
Step 3
You will need
You will need
Step 4
2 x Cam Nuts
(H4)
Insert 2 x Cam Nuts (H4) into Divider panel (P7). Attach Divider panel
(P8) to Shelf panel (P5) and secure by tightening Cam Nuts (H4) with a
Phillips Head Screwdriver.
Phillips head
screwdriver
Insert 2 x Long Dowels (H15) into Divider panel (P7), attach to Shelf panel (P5) and secure
with 2 x Large Screws (H2) by tightening with a Phillips Head Screwdriver.
*Ensure the metal track on Shelf panel is facing upwards before securing panels.
H2
H15
H4
2 x Long
Dowels (H15) 2 x Large
Screws
(H2)
(P7)
(P5)
(P5)
(P7)
H2
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
H4
H15
Phillips head
screwdriver
Ensure PVC
edge face up.
Ensure PVC
edge face up.

www.fantasticfurniture.com.au PAGE 7
2 x Cam Nuts
(H4)
(P3)
Step 5
You will need
Insert 2 x Dowels (H1) & 2 x
Cam Nuts (H4) into Shelf panel
(P5). Attach Left Side panel (P3) to
Shelf panel (P5) and secure by tightening Cam Nuts (H4) with a Phillips Head Screwdriver.
*Ensure the groove for the Back panel on the Left
Side panel is aligned with the groove of the Shelf panel.
2 x Dowels
(H1)
(P5)
(P5)
H4 H1
(P4)
Insert 2 x Dowels (H1) & 2 x Cam Nuts (H4) into Shelf panel (P5). Attach Right Side
panel (P4) to Shelf panel (P5) and secure by tightening Cam Nuts (H4) with a Phillips
Head Screwdriver.*Ensure the groove for the Back panel on the Right Side panel is
aligned with the groove of the Shelf panel.
2 x Cam Nuts
(H4)
Step 6
You will need
2 x Dowels
(H1)
H1
H4
Phillips head
screwdriver
Phillips head
screwdriver

www.fantasticfurniture.com.au PAGE 8
You will need
Step 7
Step 8
Slide Back panel (P6) into the grooves of the Left Side panel (P3) and Right Side panel (P4) as shown.
Insert 6 x Dowels (H1) into the Right
Side panel (P4), Divider panel (P7) &
Left Side panel (P3). Attach Bottom panel
(P2) to the unit and secure with 6 x Large Screws (H2)
by tightening with a Phillips Head Screwdriver.
*Ensure the groove for the Back panel on the Bottom panel is lined up at the back
of the unit.
(P7)
H2
Phillips head
screwdriver
6 x Dowels
(H1)
6 x Large
Screws (H2)
(P3)
(P4)
(P6)
(P3)
(P4)
H2
H2
H2
H2
H2
H1
H1
H1 H1
(P2)
Make sure with laminating
face inside.
(P7)

www.fantasticfurniture.com.au PAGE 9
Step 10
Apply 4 x Felt Pads (H14) to the Bottom panel (P2) as shown.
Insert 6 x Cam Bolts (H3) into Top panel (P1) and secure by tightening
Cam Bolts (H3) with a Phillips Head Screwdriver.
You will need
(P1)
Phillips head
screwdriver
6 x Cam Bolts
(H3)
Step 9
You will need
4 x Felt Pads
(H14)
H14
H14
H14
H14
H3
H3
H3
H3
H3
H3
(P2)

www.fantasticfurniture.com.au PAGE 10
Insert 6 x Dowels (H1) & 6 x Cam Nuts (H4) into the Right Side panel (P4), Divider panel
(P7) & Left Side panel (P3). Attach Top panel (P1) to the unit and secure by tightening
the Cam Nuts (H4) with a Phillips Head Screwdriver.
*Ensure the groove for the Back panel on the Top panel is lined up at the back of the unit.
Step 12
You will need
6 x Cam Nuts
(H4) 6 x Dowels
(H1)
H1 H4H1
Step 11
Slide Back panel (P6) into the grooves of the Left Side panel (P3) and Right Side panel (P4) as shown.
(P3)
(P4)
(P6)
(P1)
(P3)
(P4)
(P7)
Phillips head
screwdriver
Make sure with laminating
face inside.
(P7)