fantastic furniture STOCKHOLM LAMP TABLE User manual

Version 1.0
STOCKHOLM
LAMP TABLE
fantasticfurniture.com.au

fantasticfurniture.com.au PAGE 2
Looks like you’ve found
your Fantastic!
Love it? Share it!
Fantastic buy! Share how it looks at home for your
chance to win a $250 Fantastic Furniture Gift Card!
fantasticfurniture
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
Recommended weight capacity : 40kgs.

PAGE 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Left Side Panel (P2);
Right Side Panel (P3);
Bottom Panel (P4);
Shelf Panel (P5);
2 x Shelf Panels (P6);
Rail (P7);
Back Panel (P8);
4 x Legs (P9);
Drawer Front (P10);
Drawer Back (P11);
Left Drawer Side (P12);
Right Drawer Side (P13);
Drawer Base (P14);
Hardware pack
Rail
(P7)
Shelf Panel
(P5)
Back Panel
(P8)
12 x Cam
Bolts
(H3)
12 x Cam
Nuts
(H4)
12 x Dowels
(H1)
14 x Small
Screws
(H5)
1 x CL
Runner
Tracks
(H6)
1 x CR
Runner
Tracks
(H7)
1 x DR
Runners
(H9)
1 x DL
Runners
(H8)
8 x Long
Screws
(H2)
1 x Magnetic
Catcher
(H13)
16 x Bolts
(H14)
2 x Small
Bolts
(H19)
1 x Allen
Key
(H15)
4 x Screws
(H16)
4 x Wedges
(H10)
4 x Wedge
Screws
(H11)
1 x Screw
(H12)
Left Drawer
Side (P12)
Right Drawer
Side (P13)
Drawer Back
(P11)
Drawer
Base
(P14)
Drawer Front
(P10)
Top Panel
(P1) Right
Side
Panel
(P3)
Bottom Panel
(P4)
Left
Side
Panel
(P2)
Shelf
Panel
(P6)
4 x Legs
(P9)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
DO NOT USE
PAGE 4
fantasticfurniture.com.au
Shelf
Panel
(P6)
4 x Plates
(H17)
8 x Long
Screws
(H18)

You will need
Step 1
Phillips Head
Screwdriver
Attach 4 x Cam Bolts (H3) to Left Side Panel (P2) and Right Side Panel (P3) as shown.
Tighten with a Phillips Head Screwdriver. Attach 1 x CL Runner Track (H6) to Left Side
Panel (P2) with 3 x Small Screws (H5). Attach 1 x CR Runner Track (H7) to Right Side
panel (P3) with 3 x Small Screws (H5). Tighten with a Phillips Head Screwdriver.
(P1)
(P4)
(P3)
H3
Attach 4 x Cam Bolts (H3) to Top Panel (P1) as shown. Tighten with using a Phillips Head
Screwdriver. Attach 1 x Magnetic Catcher (H13) to Bottom Panel (P4) and secure with 4 x
Small Screws (H5). Tighten with a Phillips Head Screwdriver.
You will need
Step 2
4 x Cam Bolts
(H3)
Phillips Head
Screwdriver
(P2) H3
4 x Small
Screws (H5)
H3
4 x Cam Bolts
(H3)
1 x CL Runner
Track (H6)
1 x CR Runner
Track (H7)
6 x Small
Screws (H5)
H5
H5
H6
H7
1 x Magnetic
Catcher (H13)
fantasticfurniture.com.au PAGE 5
H6
CL
H5
H7
CR
H5
H5
H13
H5
H13
Please note the position
of the head of the Catch
before fixing.

You will need
Step 3
4 x Dowels
(H1)
Attach Left Side Panel (P2) and Right Side Panel (P3) to Top Panel (P1)
with 4 x Dowels (H1) and secure with 4 x Cam Nuts (H4).
Tighten with a Phillips Head Screwdriver.
Phillips Head
Screwdriver
(P3)
(P2)
(P5)
Attach Left Side Panel (P2) and Right Side Panel (P3) to Shelf Panel (P5) with 4 x Dowels (H1)
and secure with 4 x Cam Nuts (H4). Tighten with a Phillips Head Screwdriver.
You will need
Step 4
(P3)
(P2)
(P1)
Phillips Head
Screwdriver
H4
H1
4 x Cam Nuts
(H4)
H4
H4
4 x Cam Nuts
(H4)
4 x Dowels
(H1) H1
H4
H1
fantasticfurniture.com.au
fantasticfurniture.com.au PAGE 6
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
PVC edge

You will need
Step 6
You will need
Step 5
Slide remaining Back Panels (P8) into the groovesof Left Side Panel (P2) and Right Side
Panel (P3). Press Rail (P7) against Top Panel (P1), then slide Rail (P7) between Left Side
Panel (P2) and Right Side Panel (P3) to form the unit as shown. Attach Rail (P7) to
Top Panel (P1) secure with 2 x Small Bolts (H19). Tighten with a Phillips Head
Screwdriver.
Press 2 x Shelf Panels (P6) against Shelf Panels (P2,P3), then slide 2 x Shelf Panels (P6) between
Shelf Panels (P5) and Top Panel (P1) to form the unit as shown. Attach 2 x Shelf Panels (P6) to
Left Side Panel (P2) and Right Side Panel (P3) secure with 4 x Screws (H16).
Tighten with a Phillips Head Screwdriver.
Phillips Head
Screwdriver
4 x Screws
(H16)
(P3)
(P2)
H16
(P6)
(P6)
(P8)
(P3)
(P2)
(P1)
(P7)
H19
Ensure laminated
side of panel is
facing inwards.
(P7)
(P6)
(P5)
(P6)
(P5)
fantasticfurniture.com.au PAGE 7
(P1)
2 x Small
Bolts (H19)
1 x Allen Key
(H15)
PVC edge

You will need
Step 8
Attach 4 x Plates (H17) and 4 x Legs (P9) secure with 8 x Long Screws (H18),
attach 4 x Legs (P9) to Bottom Panel (P4) and secure with 16 x Bolts (H14).
Tighten with an Allen Key (H15).
Attach Bottom Panel (P4) to Left Side Panel (P2) and Right Side Panel (P3) with 4 x Dowels
(H1) and secure with 4 x Long Screws (H2). Tighten with a Phillips Head Screwdriver.
Step 7
You will need
16 x Bolts
(H14)
1 x Allen Key
(H15)
(P3)
(P2)
(P4)
(P9)
(P4)
4 x Long
Screws (H2)
4 x Dowels
(H1) H1
H2
fantasticfurniture.com.au PAGE 8
Phillips Head
Screwdriver
H15
H14
H14
(P9)
H17
H18
H15
Phillips Head
Screwdriver
4 x Plates
(H17)
8 x Long
Screws (H18)
Ensure the countersunk holes on
the Leg Plate are face up, so that
the Screws sit flush with the top
of the Leg Plate once attached.

You will need
Step 10
Attach Drawer Sides (P12, P13) to Drawer Fronts (P10). Insert 4 x Cam Nuts (H4) into
the holes of Drawer Sides (P12, P13). Make sure the opening on cam nuts point
towards the incoming cam bolts. Tighten with a Phillips head screwdriver.
Attach 4 x Cam Bolts (H3) and 1 x Screw (H12) to Drawer Front (P10) as shown.
Tighten with a Phillips Head Screwdriver.
You will need
Step 9
(P10)
(P12)
(P13)
(P10)
H4
H4
H3
H3
4 x Cam Bolts
(H3)
Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
Phillips Head
Screwdriver
fantasticfurniture.com.au PAGE 9
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
1 x Screw
(H12)
H12

Attach Drawer Back (P11) to Drawer Sides (P12, P13) with 4 x Long Screws (H2),
make sure that the groove lines up the whole way around the drawer.
Tighten with a Phillips Head Screwdriver.
Slide the Drawer Base (P14) into the grooves between drawer sides as shown.
(P14)
Ensure laminated
side of panel is
facing inwards.
You will need
Step 12
Step 11
PAGE 10
fantasticfurniture.com.au
(P11)
(P12)
(P13)
H2
H2
Phillips Head
Screwdriver
4 x Long
Screws (H2)

You will need
Step 13
Step 14
Insert the assembled drawer into the corresponding compartment as shown.
Ensure the drawer slide easily along the rails.
Attach 1 x DL Runner (H8) to Left Drawer Side (P12) and 1 x DR Runner (H9) to Right
Drawer Side (P13) with 4 x Small Screws (H5) using a Phillips Head Screwdriver.
fantasticfurniture.com.au PAGE 11
(P12)
(P13)
H5
H5
H5
H5
H8
H9
H13
4 x Small
Screws (H5)
1 x DL Runner
(H8)
1 x DR Runner
(H9)
Phillips Head
Screwdriver
To open the drawer, firmly press the
middle of the drawer front to trigger
the Catch to bounce the drawer open.
If the drawer does not pop open when
pressed or is not sitting flush with the
front of the unit, reach to the Rail and
adjust the head of the Catch by gently
turning left or right to reach the right
resistance.

Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
fantasticfurniture.com.au PAGE 12
Secure Back Panel (P8) in place with 4 x Wedges (H10) using 4 x Wedge Screws (H11).
Tighten with a Phillips Head Screwdriver.
Step 15
Phillips Head
Screwdriver
You will need
4 x Wedges
(H10)
4 x Wedge
Screws (H11) H10
H11
H10
H11
(P8)