fantastic furniture Coda User manual

Version 1.0
Coda
Bookcase 10 Shelf
fantasticfurniture.com.au

Secure it!
Wall attachment guide
(with available wood stud)
Screw directly into
stud.
Please seek professional advice if you are in doubt of what fixing device to use.
•
•
• Do not
•
•
Reduce the risk of furniture
tip-over accidents
(with available wood stud)
S
.
Screw
fantasticfurniture.com.aufantasticfurniture.com.au
Recommended Weight Capacity :10kg/shelf

fantasticfurniture.com.au Page 3
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 4
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Hardware pack
What you need
to assemble the product
Other tools you need:
Phillips Head Screwdriver;
Hammer
DO NOT USE
Page 5
fantasticfurniture.com.au
Top Panel
(P1)
Side Panel
(P2)
Side Panel
(P2)
Bottom Panel
(P7)
Shelf Panel
(P3)
Shelf Panel
(P4)
Shelf Panel
(P3)
Divider
(P6)
Divider
(P5)
Divider
(P5)
Divider
(P5)
Divider
(P5)
Divider
(P6)
Parts list
Top Panel (P1);
2 x Side Panels (P2);
2 x Shelf Panels (P3);
Shelf Panel (P4);
4 x Dividers (P5);
2 x Dividers (P6);
Bottom Panel (P7);
8 x Dowels
(H1)
24 x Cam Bolts
(H3)
24 x Cam Nuts
(H4)
1 x Allen Key
(H7)
12 x Inside
Hexagonal Bolts
(H6)
16 x Covers
(H8)
8 x Long
Screws
(H5)
36 x Small
Dowels
(H2)
8 x Plastic
Glides
(H9)
2 x Screws
(H11)
2 x Restraint
Straps
(H10)
4 x Brackets
(H12)
2 x Safety
Strap Sets

You will need
Step 1
You will need
Step 2
12 x Cam Bolts
(H3)
Phillips Head
Screwdriver
You will need
Step 3
Page 6
fantasticfurniture.com.au
H3
(P2) x 2
H3 H3
H3 H3
H3
Attach 6 x Cam Bolts (H3) into each Side Panel (P2) as shown.
(P3) x 2
H3
H3
H3
H3
8 x Cam Bolts
(H3)
Phillips Head
Screwdriver
Attach 4 x Cam Bolts (H3) into each Shelf Panel (P3) as shown.
(P4)
H3
H3
2 x Cam Bolts
(H3)
Phillips Head
Screwdriver
Attach 2 x Cam Bolts (H3) into Shelf Panel (P4) as shown.

Step 5
You will need
You will need
Step 4
Page 7
fantasticfurniture.com.au
x 2
(P5)
(P3)
H5
H5
H2
4 x Long
Screws (H5)
Phillips Head
Screwdriver
4 x Small
Dowels (H2)
Insert 2 x Small Dowels (H2) into the holes of Divider (P5) as shown.
Attach Shelf Panel (P3) to Divider (P5) with 2 x Long Screws (H5).
Tighten the screws with a Phillips Head Screwdriver.
Repeat Step 4 for the other Divider (P5) and Shelf Panel (P3).
(P5)
(P5)
(P4)
H5
H5
H5
H5
H2
H2
4 x Long
Screws (H5)
Phillips Head
Screwdriver
Insert 4 x Small Dowels (H2) into the holes of Shelf Panel (P4) as shown.
Attach Dividers (P5) to Shelf Panel (P4) with 4 x Long Screws (H5).
Tighten the screws with a Phillips Head Screwdriver.
4 x Small
Dowels (H2)

You will need
Step 6
You will need
Step 7
Page 8
fantasticfurniture.com.au
(P3)
(P3)
(P4)
(P5)
(P5)
(P5)
(P6)
(P6)
H2
H4
H4
H2
H8
H8
H2
H4
H4
H2
H8
H2
H2
H4
H4
H2
H8
H8
H2
H4
H4
H2
H8
H8
H2
H4
H2
Required
Two People
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Insert 10 x Small Dowels (H2) into the holes of Shelf Panels (P3, P4).
Insert 10 x Cam Nuts (H4) into the holes of Dividers (P5, P6).
Rotate the Cam Nuts so the arrows point towards the incoming Cam Bolts.
Push Dividers (P5, P6) into place and then tighten the Cam Nuts using a Phillips Head Screwdriver.
Seal the holes with 10 x Covers (H8) as shown.
10 x Cam Nuts
(H4)
10 x Covers
(H8)
10 x Small
Dowels (H2)
(P2)
(P3) (P4)
(P3)
H2
H4
H4
H2
H2 H4
H4
6 x Cam Nuts
(H4)
6 x Small
Dowels (H2)
Insert 6 x Small Dowels (H2) into the holes of Shelf Panels (P3, P4).
Insert 6 x Cam Nuts (H4) into the holes of Shelf Panels (P3, P4).
Rotate the Cam Nuts so the arrows point towards the incoming Cam Bolts.
Push Side Panel (P2) into place and then tighten the Cam Nuts.
Phillips Head
Screwdriver
Phillips Head
Screwdriver

You will need
Step 9
You will need
Step 8
Page 9
fantasticfurniture.com.au
(P2)
(P3)
(P4)
(P3)
H2
H4
H2
H4
H2
H4
H4
Insert 6 x Small Dowels (H2) into the holes of Shelf Panels (P3, P4).
Insert 6 x Cam Nuts (H4) into the holes of Shelf Panels (P3, P4).
Rotate the Cam Nuts so the arrows point towards the incoming Cam Bolts.
Push Side Panel (P2) into place and then tighten the Cam Nuts.
6 x Cam Nuts
(H4)
6 x Small
Dowels (H2)
(P1)
H3
H3
Attach 2 x Cam Bolts (H3) into Top Panel (P1) as shown.
2 x Cam Bolts
(H3)
Phillips Head
Screwdriver
Phillips Head
Screwdriver

You will need
Step 10
You will need
Step 11
Page 10
fantasticfurniture.com.au
(P2)
(P2)
(P5)
(P1)
H1
H1
H8
H4
H2
2 x Cam Nuts
(H4)
4 x Dowels
(H1)
2 x Covers
(H8)
2 x Small
Dowels (H2)
Insert 4 x Dowels (H1) into the holes of Side Panels (P2).
Insert 2 x Small Dowels (H2) into the holes of Divider (P5).
Insert 2 x Cam Nuts (H4) into the holes of Divider (P5).
Rotate the Cam Nuts so the arrows point towards the incoming Cam Bolts.
Attach Top Panel (P1) to Side Panels (P2) and Divider (P5).
Tighten the Cam Nuts using a Phillips Head Screwdriver.
Seal the holes with 2 x Covers (H8) as shown.
(P2)
(P2)
(P1)
H6
H8
H8
H8
H6
H6
H7
Secure Top Panel (P1) to Side Panels (P2) with
4 x Inside Hexagonal Bolts (H6) using an Allen Key (H7).
Seal the holes with 4 x Covers (H8) as shown.
4 x Inside
Hexagonal Bolts
(H6)
1 x Allen Key
(H7)
4 x Covers
(H8)
Phillips Head
Screwdriver