fantastic furniture Eden Utility Pants Storage Clothes Rack User manual

Eden
Utility Pants Storage Clothes Rack
fantasticfurniture.com.au
Version 1.0

fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 15kg/hanging rail
or drawer rack.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Page 2

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
2 x Top/Base Panels (P1);
Left Side Panel (P2);
Right Side Panel (P3);
Shelf Panel (P4);
2 x Back Panels (P5);
2 x Rails (P6);
2 x Back Panels (P7);
Drawer Front (P8);
2 x Drawer Sides (P9);
7 x Hanging Rods (P10);
Drawer Back (P11)
Hardware pack
Top/Base Panel
(P1)
Top/Base Panel
(P1)
Shelf Panel
(P4)
Right Side
Panel (P3)
Left Side
Panel (P2)
Rail
(P6)
Rail
(P6)
Back
Panel
(P7)
Back
Panel
(P5)
Back
Panel
(P5)
Back
Panel
(P7)
Drawer
Side (P9)
Drawer
Front (P8)
Drawer
Side (P9)
Drawer
Back (P11)
7 x Hanging Rods
(P10)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
16 x Dowels
(H1)
4 x Long
Screws
(H2)
16 x Small
Screws
(H5)
2 x Slides
(H6)
16 x Cam
Bolts
(H3)
16 x Cam
Nuts
(H4)
2 x Hanging Rail
Support
(H8)
1 x Hanging Rail
(H9)
4 x Small Cam
Bolts
(H7)
4 x Small Cam
Nuts
(H10)
12 x Wedges
(H12)
4 x Plastic
Glides
(H11)
12 x Wedge
Screws
(H13)
1 x Safety
Strap
Screw
(H15)
1 x Safety
Strap
(H14)
2 x Washers
(H16)

3 x Small
Screws (H5)
3 x Small
Screws (H5)
8 x Cam Bolts
(H3)
1 x Slide
(H6)
(P2)
(P3)
You will need
Step 1
Step 2
You will need
Attach 8 x Cam Bolts (H3) to Left Side Panel (P2) as shown by tightening with the
Phillips Head Screwdriver. Attach 1 x Slide Track (H6-1) to Left Side Panel (P2) with
3 x Small Screws (H5) as shown by tightening with the Phillips Head Screwdriver.
Separate the slide runners (H6-2) and slide tracks (H6-1) from Slide (H6)
by following the steps below. Extend the slide runner all the way
forward. Press the plastic release lever of the slide down and pull
the slide runner (H6-2) completely out.
fantasticfurniture.com.au Page 5
8 x Cam Bolts
(H3)
Phillips Head
Screwdriver
H3
H6
Slide Runner
(H6-2)
Slide Track
(H6-1)
Slide Track
(H6-1)
Slide Track
(H6-1)
H3
H3
H3
H6-1
H6-1
H3
H3
H3
H3
H3
H3
H3
H3
H5
H5
Phillips Head
Screwdriver
Attach 8 x Cam Bolts (H3) to Right Side Panel (P3) as shown by tightening with the
Phillips Head Screwdriver. Attach 1 x Slide Track (H6-1) to Right Side Panel (P3) with
3 x Small Screws (H5) by as shown tightening with the Phillips Head Screwdriver.
1 x Slide
(H6)
H5 H5 H5
H5 H5 H5

Slide Back Panels (P7 x 2 & P5 x 2) into the grooves
of Top/Base Panels (P1 x 2) and Shelf Panel (P4).
Ensure laminated
side of panels are
facing inwards.
(P2)
(P1)
(P1)
(P1)
(P7)
(P5)
(P5)
(P7)
(P1)
(P6)
(P6)
(P4)
(P4)
fantasticfurniture.com.au Page 6
H4
H4
H4
H1
H1
H1
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Step 4
Step 3
You will need
Phillips Head
Screwdriver
8 x Cam Nuts
(H4)
8 x Dowels
(H1)
Insert 8 x Dowels (H1) into
Left Side Panel (P2). Insert 8 x
Cam Nuts (H4) into Top/Base Panels (P1 x 2),
Shelf Panel (P4) and Rails (P6 x 2). Rotate
the nuts so the arrows point towards the
incoming bolts. Attach Top/Base Panels (P1 x 2),
Shelf Panel (P4) and Rails (P6 x 2) to Left Side Panel (P2)
by tightening all nuts with the Phillips Head Screwdriver.
Ensure the grooves in the Top/Base
Panels (P6 x 2) and Shelf Panel (P4) are
located at the back of the unit.
Grooves for
back panels

Step 5
You will need
You will need
Step 6
Secure 4 x Plastic Glides (H11) to the bottom of Left & Right Side Panels (P2 & P3)
as shown using the Hammer.
(P1)
(P1)
(P6)
(P6)
(P4)
(P3)
(P3)
(P2)
fantasticfurniture.com.au Page 7
H4
H4
H4
H11
H1
H1
H1
Phillips Head
Screwdriver
Hammer
8 x Cam Nuts
(H4)
8 x Dowels
(H1)
H11
H11
H11
4 x Plastic
Glides (H11)
Insert 8 x Dowels (H1) into
Top/Base Panels (P1 x 2), Shelf Panel (P4)
and Rails (P6 x 2). Insert 8 x
Cam Nuts (H4) into Top/Base Panels (P1 x 2),
Shelf Panel (P4) and Rails (P6 x 2). Rotate
the nuts so the arrows point towards the
incoming bolts. Attach Right Side Panel (P3) to Top/Base Panels (P1 x 2),
Shelf Panel (P4) and Rails (P6 x 2) by tightening all nuts with the Phillips Head Screwdriver.

You will need
Phillips Head
Screwdriver
Step 7
You will need
Phillips Head
Screwdriver
Step 8
Attach 4 x Small Cam Bolts (H7) to Drawer Front (P8) as shown by tightening with the
Phillips Head Screwdriver.
(P8)
(P8)
(P9)
(P9)
fantasticfurniture.com.au Page 8
4 x Small Cam
Bolts (H7)
4 x Small Cam
Nuts (H10)
H7 H7
H7 H7
H10 H10
H10
H10
Insert 4 x Small Cam Nuts (H10) into the holes of Drawer Sides (P9 x 2).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Drawer Sides (P9 x 2) to Drawer Front (P8) by tightening the cam nuts
with the Phillips Head Screwdriver.

Step 9
Step 10
You will need
Phillips Head
Screwdriver
Insert 7 x Hanging Rods (P10) into the holes of Drawer Front (H8) as shown.
Attach Drawer Back (P11) to Drawer Sides (P9 x 2) with 4 x Long Screws (H2) by
tightening with the Phillips Head Screwdriver.
(P8)
(P10)
(P9)
(P9)
(P9)
(P9)
(P11)
H2
H2
fantasticfurniture.com.au Page 9
4 x Long
Screws (H2)

You will need
Step 11
Step 12
Attach 2 x Slide Runners (H6-2) to Drawer Sides (P9 x 2) with 6 x Small Screws (H5) as shown
by tightening with the Phillips Head Screwdriver.
Position drawer so that slide runner (H6-2) aligns with slide track (H6-1) as shown.
Gently push drawer into the closed positon.
Phillips Head
Screwdriver
Move Inner Ball Bearing
Track outward.
Gently Insert Slide Runner
into Ball Bearing Track.
(P9)
(P3)
(P9)
(P2)
H5
H5
H5
H5
H5
H5
H6-2
H6-2
fantasticfurniture.com.au Page 10
6 x Small
Screws (H5)
2 x Slide
Runners (H6-2)
Slide Runner (H6-2)
H5 H5 H5
√
X
X
!