fantastic furniture COMO User manual

Version 1.0
COMO
DESK STUDENT 2 DRAWER
fantasticfurniture.com.au

fantasticfurniture.com.au PAGE 2
Looks like you’ve found
your Fantastic!
Love it? Share it!
Fantastic buy! Share how it looks at home for your
chance to win a $250 Fantastic Furniture Gift Card!
fantasticfurniture
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
Recommended weight capacity : 50kgs.

PAGE 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Left Side Panel (P2) ;
Right Side Panel (P3);
Divider (P4);
Shelf Panel (P5);
2 x Rail (P6);
2 x Rail (P7);
Rail (P8) ;
Back Panel (P9);
Back Panel (P10);
2 x Drawer Front (P11);
2 x Left Drawer Side (P12);
2 x Right Drawer Side (P13);
2 x Drawer Base (P14);
2 x Drawer Back (P15)
Hardware pack
Top Panel
(P1)
Right Side
Panel
(P3)
Left Drawer
Side
(P12)
Drawer Front
(P11)
x 2
Right Drawer
Side
(P13)
Drawer Back
(P15)
Drawer Base
(P14)
Left Side
Panel
(P2)
Divider
(P4)
Rail
(P6)
Rail
(P6)
Rail
(P7)
Rail
(P8)
Rail
(P7)
Shelf Panel
(P5)
Back
Panel(P10)
Back Panel
(P9)
30 x Dowels
(H1)
8 x Long Screws
(H2)
20 x Small
Screws
(H5)
2 x CL Runner
Tracks
(H6)
24 x Cam Bolts
(H3)
24 x Cam Nuts
(H4)
8 x Small
Cam Nuts
(H11)
2 x CR Runner
Tracks
(H7)
2 x DL Runners
(H8)
2 x DR Runners
(H9)
8 x Small
Cam Bolts
(H10)
6 x Plastic
Glides
(H12)
PAGE 4
fantasticfurniture.com.au
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
DO NOT USE

You will need
Step 1
Phillips head
screwdriver
Step 2
You will need
Phillips head
screwdriver
Step 3
You will need
Attach 2 x CL Runner Tracks (H6) to Left Side Panel (P2) with 6 x Small Screws (H5) by tightening
with the Phillips Head Screwdriver.
(P4)
(P2)
H1
H1
H1
H1
H1 H1
H1
H3
H3
H3
H3
H3
H3
H3
2 x CL Runners
Tracks (H6)
H5
H5
H5
H5
H5
H5
H6
H6
(P2) H6
CL
H5
6 x Small
Screws (H5)
2 x CR Runners
Tracks (H7)
6 x Small
Screws (H5)
10 x Dowels
(H1)
10 x Cam Bolts
(H3)
Phillips head
screwdriver
PAGE 5
fantasticfurniture.com.au
Insert 10 x Dowels (H1) into Left Side Panel (P2).Attach 10 x Cam Bolts (H3) into Left
Side Panel (P2) and Divider (P4) by tightening with the Phillips Head Screwdriver as
shown
H5
H5
H5 H7
H7
H5
H5
H5
(P4)
Attach 2 x CR Runner Tracks (H7) to Divider (P4) with 6 x Small Screws (H5) by tightening with the
Phillips Head Screwdriver.
H7
CR
H5

Step 4
You will need
You will need
Step 5
(P2)
H4
(P6)
(P6)
(P7)
(P7)
H4
H4
(P2)
(P8)
(P5)
H4
H4
H4
Insert 1 x Cam Nut (H4) into each Rail (P7x2). Rotate the cam nuts so the arrows point towards
the incoming cam bolts. Attach Rails (P7x2) to the Left Side Panel (P2) by tightening the cam nuts
with the Phillips Head Screwdriver. Attach Rails (P6x2) to Left Side Panel (P2) as shown.
Insert 3 x Cam Nuts (H4) into
Shelf Panel (P5). Rotate the cam
nuts so the arrows point towards the
incoming cam bolts. Attach Shelf Panel
(P5) to Left Side Panel (P2) by tightening
the cam nuts with the Phillips Head Screwdriver.
Attach Rail (P8) to Left Side Panel (P2) as shown.
2 x Cam Nuts
(H4)
3 x Cam Nuts
(H4)
Phillips head
screwdriver
Phillips head
screwdriver
PAGE 6
fantasticfurniture.com.au
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.

Slide Back Panel (P9) into the groove of Shelf Panel (P5) and Rail (P8).
Step 6
You will need
Hammer
5 x Cam Nuts
(H4)
4 x Plastic
Glides (H12)
10 x Dowels
(H1)
Phillips head
screwdriver
Ensure laminated side
is facing inwards.
PAGE 7
fantasticfurniture.com.au
Step 7
(P9)
(P8)
(P5)
(P10)
(P2)
(P4)
(P6) (P6)
(P7)
(P8)
(P7)
(P5)
H12
H12
H12
H12
H1 H1
H1
H1
H1
H1
H1
H1 H1
H4
H4
H4
H4
H4
H12
2cm
Insert 3 x Cam Nuts (H4) into
Shelf Panel (P5) and 1 x Cam
Nut (H4) into each Rail (P7x2). Rotate
the cam nuts so the arrows point towards
the incoming cam bolts. Insert 2 x
Dowels (H1) into Shelf Panel (P5), 2 x
Dowels (H1) into each Rail (P6x2), 1 x Dowel (H1) into
Rails (P7x2) and 2 x Dowels (H1) into Rail (P8). Attach the
Divider Panel (P4) to the partially assembled unit by tightening the cam nuts with the
Phillips Head Screwdriver. Use the Hammer to secure the 4 x Plastic Glides (H12) to
the bottom of Left Side Panel (P2) and Divider Panel (P4) as shown.

Step 8
You will need
2 x Dowels
(H1)
You will need
2 x Cam Nuts
(H4)
Insert 2 x Cam Nuts (H4) into Back Panel (P10). Rotate the cam nuts so the arrows point
towards the incoming cam bolts. Attach Back Panel (P10) to Right Side Panel (P3) by
tightening cam nuts with the Phillips Head Screwdriver.
2 x Cam Bolts
(H3)
2 x Plastic
Glides (H12)
Phillips head
screwdriver
Hammer
Phillips head
screwdriver
PAGE 8
fantasticfurniture.com.au
Step 9
H1
H1
H12
H12
Insert 2 x Dowels (H1) into Right Side Panel (P3). Attach 2 x Cam Bolts (H3) to Right Side Panel
(P3) by tightening with the Phillips Head Screwdriver. Use the Hammer to secure the 2 x Plastic
Glides (H12) to the bottom of Right Side Panel (P2) as shown.
(P3)
H3
H3
(P3)
(P10)
H3
H3
H4
H4

Step 10
You will need
2 x Cam Nuts
(H4)
2 x Dowels
(H1)
You will need
2 x Cam Bolts
(H3)
Phillips head
screwdriver
10 x Cam Bolts
(H3)
Phillips head
screwdriver
PAGE 9
fantasticfurniture.com.au
Required
Two People
Step 11
(P10)
(P3)
(P4)
H3 H4
H4
H1
Attach 2 x Cam Bolts (H3) to Divider Panel (P4) by tightening with the Phillips Head Screwdriver.
Insert 2 x Dowels (H1) and 2 x Cam Nuts (H4) into Back Panel (P10). Rotate the cam nuts so the
arrows point towards the incoming cam bolts. Attach Back Panel (P10) to Divider Panel (P4) by
tightening cam nuts with the Phillips Head Screwdriver.
(P1)
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
Attach 10 x Cam Bolts (H3) to Top Panel (P1) by tightening
with the Phillips Head Screwdriver.

Step 12
You will need
10 x Cam Nuts
(H4)
6 x Dowels
(H1)
You will need
(P1)
(P2)
(P3)
(P10)
(P4)
H1
H1
H1
H1
H4
H4
H4
H4 H4
H1
H1
H4
H4
H4
H4 H4
Insert 3 x Cam Nuts (H4) into Left Side Panel (P2) , 3 x Cam Nuts (H4) into Divider Panel (P4), 3 x
Cam Nuts (H4) into Right Side Panel (P3) and 1 x Cam Nut (H4) into Back Panel (P10). Rotate the
cam nuts so the arrows point towards the incoming cam bolts. Insert 2 x Dowels (H1) into Left
Side Panel (P2), 2 x Dowels (H1) into Divider Panel (P4) and 2 x Dowels (H1) into Right Side Panel
(P3). Attach Top Panel (P1) to the assembled unit by tightening cam nuts with the Phillips Head
Screwdriver.
H10
H10
(P11)
H10 H10
Phillips head
screwdriver
8 x Small
Cam Bolts (H10)
Phillips head
screwdriver
PAGE 10
fantasticfurniture.com.au
Required
Two People
Step 13
Attach 4 x Small Cam Bolts (H10) to Drawer Front (P11) by tightening with the
Phillips Head Screwdriver. Repeat steps for the second drawer.