fantastic furniture GEO BOOKCASE 9 CUBE User manual

Assembly Instructions
GEO
BOOKCASE 9 CUBE

Page 2
12
3
56
STOP!
Before you start...
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
location before fastening.
DO NOT over-tighten screws DO NOT set glue until you are certain that the
parts belong together.

What You Need
(Tools not provided)
Phillips Head Srewdriver
Mallet
Page 3
Top Panel
(P1)
Left Side
Panel
(P3)
Rihgt Side
Panel
(P2)
Mid Panel
(P4)
Mid Panel
(P4)
Shelf
(P5)
Shelf
(P5)
Shelf
(P5)
Shelf
(P5)
Shelf
(P5)
Shelf
(P5)
Bottom Panel
(P6)
16 x Long
Dowels
(H1)
24 x Short
Dowels
(H2)
6 x Cam
Bolts
(H3)
6 x Cam
Nuts
(H4)
6 x Allen
Bolts
(H5)
16 x Screws
(H6)
2 x Brake
Wheels
(H7)
2 x Wheels
(H8)
1 x allen key

Step 2
Insert the long dowels (H1) into the dowel holes of the mid panel (P4), connect the shelves (P5) to the
douwels which attached to the mid panel.
Use the long dowels (H1) to conect the other mid panel (P4) to the step 1 shelves.
Page 4
Step 1
8 x Long
Dowels
(H1)
You will need:
You will need:
4 x Long
Dowels
(H1)
(P4)
(H1) (H1)
(P5)
(P5)
(P5)
(P5)
(P4)
(P4)
(H1) (H1)

Step 3
Page 5
Step 4
You will need:
4 x Short
Dowels
(H2)
Connect the shelves (P5) to the long dowels that in the mid panel on Setp 2, Iisert the short dowels (H2)
into the Shelves (P5).
Conect the left side panel (P3) and the right side panel (P2) to the shelves
(P5), then insert the short dowels (H2) into the dowel holes which on the top
and bottom of panels (P2) and (P3). .
(P4) (P4)
(P5)
(P5)
(H2) (H2)
(P4)
(P5)
(H2)
(P3) (P2)
(P5)
(P5)
(P5)
(P4)
(H2) (H2) (H2) (H2)
(H2)
(H2) (H2)
You will need:
16 x Short
Dowels
(H2)
(P5)
(P5)

Page 6
Step 5
6 x Cam
Bolts
(H3)
You will need:
Screw the cam bolts (H3) into the top panel (P1).
Insert the cam nuts (H4) into the panels (P2),(P3) and (P4), cover the top panel (P1) to the those
panels. Rotate the cam nuts so the arrows point towards the incoming cam bolts.Push the top
panel (P1) into place and tighten the cam nuts.
(P1)
(H3) (H3)
(P4)
(P3) (P4) (P2)
(P1)
Step 6
6 x Cam
Nuts
(H4)
You will need:
(H4) (H4) (H4)

Step 7
Page 7
You will need:
6 x Allen
Bolts
(H5)
Screw the bottom panel (P6) to the panels (P2),(P3),(P4) using the allen bolts (H5).
Align each wheel with the 4 pilot holes in the bottom panel (P6). Place the two brake wheels
nearest to the front of the unit. Screw the castors into place with the screws (H6) .
(P4)
(P3) (P4) (P2)
(H5) (H5) (H5)
(P6)
Step 8
You will need:
2 X Wheel
(H8)
2 x Brake
Wheel
(H7)
16 x Screws
(H6)
(H6)
(H7)
(H8)
(H7)
(H8)
(P1)
(P6)

Step 9
Page 8
The job is now complete!
In the interest of our environment
Please dispose of all packaging thoughtfully.