fantastic furniture HAVANA Table Nest Rectangle User manual

HAVANA
Table Nest Rectangle
www.fantasticfurniture.com.au
Version 1.0

Enjoy
Your purchase from
Australia’s Best Value Furniture Store
www.fantasticfurniture.com.au PAGE 2

Assembly checklist
Useful Information
www.fantasticfurniture.com.au PAGE 3
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never ues any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk bed should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (sucn as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.

Top Panel
(P1)
Top Panel
(P8)
LF
Leg
(P2)
LF
Leg
(P9)
RR
Leg
(P5)
RR
Leg
(P12)
RF
Leg
(P3)
RF
Leg
(P10)
RF
Leg
(P4)
RF
Leg
(P11)
Long Apron
(P6)
Long
Apron
(P13)
Long
Apron
(P13)
Short
Apron
(P14)
Short
Apron
(P7)
Short
Apron
(P7)
16 x Dowels
(H1)
18 x Cam Bolts
(H2)
18 x Cam Nuts
(H3)
2 x Long Bolts
(H4)
2 x Hexagonal Nuts
(H6)
2 x Half Round
Nuts
(H5)
1 x Spanner
(H7)
6 x Screws
(H9)
2 x Glues
(H10)
12 x Small Dowels
(H8)
LF : Left Front
LR : Left Rear
RF : Right Front
RR : Right Rear
What you need
to assemble the product
Other tools you need
Flat head screwdriver; Phillips head
screwdriver; Hammer
Parts list
Box 1: Top Panel (P1); LF Leg (P2);
RF Leg (P3); RF Leg (P4);
RR Leg (P5); Long Apron (P6);
Short Apron (P7);
Top Panel (P8); LF Leg (P9);
RF Leg (P10); RF Leg (P11);
RR Leg (P12); Long Apron (P13);
Short Apron (P14);
www.fantasticfurniture.com.au PAGE 4
DO NOT USE
8 x Plastic Glides
(H11)

(P2)
(P7)
(P7)
(P4)
(P4)
(P3)
(P3)
(P5)
H2
H8
H8
Squeeze Glue (H10) into the dowel holes in Short Aprons (P7).
Insert
4 x Cam Nuts (H4) into the holes of Short Aprons (P7) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Legs (P2, P4) and Legs (P3, P5) to Short Aprons (P7),
then tighten the cam nuts using a Flat head screwdriver.
Make sure the side with the bigger
holes of the Short Aprons (P7)
is facing to the bottom of Legs.
H2
H8
H8
H10
H10
H10
H2
H3
H2
(P2)
H8
H2
H3
H3
H3
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Squeeze Glue (H10) into dowel holes in Legs (P2, P3, P4, P5) and insert 6 x Small Dowels (H8).
Screw
6 x Cam Bolts (H2) into place using a Phillips head screwdriver.
www.fantasticfurniture.com.au PAGE 5
Phillips head
screwdriver
You will need
Step 1
6 x Cam Bolts
(H2)
6 x Small
Dowels (H8)
1 x Glue
(H10)
1 x Glue
(H10)
You will need
4 x Cam Nuts
(H3)
Step 2
Flat head
screwdriver
(P5)
H8
H2

(P6)
(P4)
(P5)
H1
H1
H4
H1
H1
H2
H10
H1
H1
H2
H4
H1
H1
H3
H10
H3
www.fantasticfurniture.com.au PAGE 6
1 x Glue
(H10)
You will need
2 x Cam Nuts
(H3)
Step 3
Flat head
screwdriver
1 x Glue
(H10)
You will need
Step 4
Squeeze Glue (H10) into dowel holes in Long Apron (P6).
Insert 2 x Cam Nuts (H3) into the holes of Long Apron (P6)
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Long Apron (P6) to Legs (P4, P5), then tighten the cam nuts using a Flat head screwdriver.
Hammer 4 x Plastic Glides (H11) into end of each leg.
2 x Long Bolts
(H4)
2 x Cam Bolts
(H2)
Phillips head
screwdriver
8 x Dowels
(H1)
Squeeze Glue (H10) into dowel holes in Top Panel (P1) and insert 8 x Dowels (H1).
Screw 2 x Cam Bolts (H2) into Top Panel (P1) with a Phillips head screwdriver.
Insert
2 x Long Bolts (H4) into place as shown.
Make sure the side with the bigger
holes of the Long Apron (P6)
is facing up.
4 x Plastic
Glides (H11)
Hammer
H11
H11
H11
H11

(P1)
(P4)
(P5)
H9
H3
H3
H9
H9
H7
H5 H6
Squeeze Glue (H10) to dowels in Top Panel (P1).
Insert 2 x Cam Nuts (H3) into the holes of Legs (P4, P5).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach table leg fram to Top Panel (P1) with 2 x Half Round Nuts (H5)
and 2 x Hexagonal Nuts (H6) using Spanner (H7).
Tighten Cam nuts using a Flat head screwdriver.
Attach table leg frame to Top Panel (P1) with 3 x Screws using a Phillips head screwdriver.
(P9)
(P12)
(P10)
H2
H2
H8
H8
H8
H8
H2
H8
H2
(P11)
H2
H2
H8
www.fantasticfurniture.com.au PAGE 7
2 x Cam Nuts
(H3)
Flat head
screwdriver
Phillips head
screwdriver
You will need
Step 5
2 x Half Round
Nuts (H5)
2 x Hexagonal
Nuts (H6)
3 x Screws
(H9)
1 x Spanner
(H7)
1 x Glue
(H10)
H10
H10
Squeeze Glue (H10) into dowel holes in Legs (P9, P10, P11, P12) and insert 6 x Small Dowels (H8).
Screw
6 x Cam Bolts (H2) into place using a Phillips head screwdriver.
Phillips head
screwdriver
You will need
Step 6
6 x Cam Bolts
(H2)
6 x Small
Dowels (H8)
1 x Glue
(H10)

(P13)
(P12)
(P9)
(P11)
(P10)
(P13)
H3
H3
H3
H3
www.fantasticfurniture.com.au PAGE 8
(P14)
(P9)
(P10)
(P12)
(P11)
H3
H11
H11
H11
H11
H3
Squeeze Glue (H10) into dowel holes in Short Apron (P14).
Insert 2 x Cam Nuts (H3) into the holes of Short Apron (P14).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Short Apron (P14) to Legs (P9, P10),
then tighten the cam nuts using a Flat head screwdriver.
Hammer 4 x Plastic Glides (H11) into end of each leg.
H10
Squeeze Glue (H10) into the dowel holes in Long Aprons (P13).
Insert
4 x Cam Nuts (H4) into the holes of Long Aprons (P13) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Legs (P9, P11) and Legs (P10, P12) to Long Aprons (P13),
then tighten the cam nuts using a Flat head screwdriver.
H10
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
1 x Glue
(H10)
You will need
4 x Cam Nuts
(H3)
Step 7
Flat head
screwdriver
1 x Glue
(H10)
You will need
2 x Cam Nuts
(H3)
Step 8
Flat head
screwdriver
Make sure the side with the bigger
holes of the Long Aprons (P13)
is facing to the bottom of Legs.
Make sure the side with the bigger
holes of the Short Apron (P14)
is facing up.
4 x Plastic
Glides (H11)
Hammer

Squeeze Glue (H10) to dowels in Top Panel (P8).
Insert 4 x Cam Nuts (H3) into the holes of Legs (P9, P10, P11, P12).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach table leg frame to Top Panel (P1), tighten Cam nuts using a Flat head screwdriver.
Attach Long Apron to Top Panel (P1) with 3 x Screws using a Phillips head screwdriver.
(P8)
(P8)
H1
H1
H2
H9
H1
H1
H2
H1
H1
H2
H2
H1
H1
H9
H9
www.fantasticfurniture.com.au PAGE 9
(P9)
(P10)
(P12)
(P11)
H3
H3
4 x Cam Nuts
(H3)
Flat head
screwdriver
Phillips head
screwdriver
You will need
Step 10
3 x Screws
(H9)
1 x Glue
(H10)
H10
1 x Glue
(H10)
You will need
Step 9
4 x Cam Bolts
(H2)
Phillips head
screwdriver
8 x Dowels
(H1)
Squeeze Glue (H10) into dowel holes in Top Panel (P8) and insert 8 x Dowels (H1).
Screw 4 x Cam Bolts (H2) into Top Panel (P8) with a Phillips head screwdriver.

Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
www.fantasticfurniture.com.au PAGE 10
Step 11
Step 12
Recommended weight capacity : 80KG.