Festo NEBM-H6G4-Q13-LE4 Series User manual

6.
8.
NEBM-H6G4-...-Q13...-LE4
Motor cable
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
[phone]
www.festo.com
Assembly instructions
8174235
2022-04b
[8174237]
Translation of the original instructions
© 2022 all rights reserved to Festo SE & Co. KG
1Applicable documents
All available documents for the product è www.festo.com/sp.
2 Safety
2.1 Safety instructions
–Work on the product may only be carried out by qualified personnel who can
evaluate the work and detect dangers. The qualified personnel are trained in
electrical engineering.
–Do not connect or disconnect the push-in connector while the voltage is live.
–Do not wire or disconnect an open cable end when powered.
–Only mount the product on components that are in a condition to be safely
operated.
2.2 Intended use
Connection of a motor EMMB-AS to a servo drive CMMB-AS or CMMT-AS.
3 Additional information
–Accessories è www.festo.com/catalogue.
4 Structure
4.1 Product design
1 23
4 5
Fig.1
1
Socket, plug pattern H6, 4-pin
2
wire end sleeve (3x)
3
Cables
4
PE insulated wire
5
Extension sleeve
4.2 Contact assignment
Electrical connection 1
Field device side
Assignment/signal Electrical connection 2
Controller side
1 Socket Pin 2 Wire ends1)
1 U WH or YE
2 V RD
3 W BK
4 PE, shielding GNYE
1) Colour code in accordance with IEC 60757:2021-06
Tab. 1: Contact assignment
5 Assembly
5.1 Mounting electrical connection 1
1. Align the socket 1 to fit the plug.
2. Connect the socket 1 to the plug and click into place.
5.2 Mounting electrical connection 2
For servo drive CMMB-AS
•Connect the wires in accordance with the contact assignment.
For servo drive CMMT-AS
1. Detach the clevis shoe 5.
2. Strip the insulated wire 4 and attach a wire end sleeve (1x 0.75 mm2 x 10).
3. Connect the wires in accordance with the contact assignment.
5.3 Wiring
Feature Cable characteristic Wiring
-K Standard Flexible (freely movable, unguided wiring)
The line can be dynamically bent, but not for robots
or energy chains.
-E Suitable for energy chains In energy chain or flexible
Tab. 2: Wiring
5.4 Mounting in energy chain
1. Lay out the energy chain lengthways.
2. Place the cables in the energy chain without twisting them.
3. Separate cables from each other using separators/drilled holes.
4. Do not bind cables in bundles.
5. Maintain space X. X > 10% of the cable diameter D.
With the energy chain hanging vertically: increase the space X.
Align the energy chain in the working position:
–Make sure that the radius is greater than the bending radius R of the
cables.
–The cables can move freely in the bending radius KR of the energy chain.
ÄThe cable movement is not forced by the energy chain.
7. Mount the energy chain è corresponding instruction manual.
Fasten the cables:
–for short energy chains with a length < 1 m at both ends of the energy chain
–for long sliding energy chains with a length > 1 m at the driver end only
9. Do not move cables all the way to the fastening point.
ÄThe mounting space A between the fastening point and bending move-
ment is maintained.
NOTICE
Damage to cables if the chain breaks.
• Replace cables after a chain break.
NOTICE
Malfunction and material damage due to vertically suspended cables.
The cables stretch.
• Regularly check the length of the cables.
•Readjust the cables if required.

6 Technical data
NEBM-H6G4...-Q13...-LE4 -E -K
Certificates, declaration of conformity è www.festo.com/sp
Cable characteristic Suitable for energy
chains
Standard
Cable function Power line
Cable composition [mm²] 4x0.79 (AWG 18)
Shielding Shielded
Cable diameter D [mm] 7.3 7.4
Mounting space A [mm] 146 –
Current rating at 40 °C [A] 9.5
Surge resistance [kV] 2
Operating voltage range
AC UB[V] 0 … 300
DC UB[V] 0 … 300
Bending radius
Fixed cable installation R [mm] ³ 55 ³ 74
Flexible cable installation R [mm] ³ 55 ³ 111
Ambient temperature
Fixed cable installation [°C] –25 … +90
Flexible cable installation [°C] –25 … +90
Material
Cable sheath PVC TPE-E
Insulating sheath PVC [SR-PVC] TPE-E
Note on materials Contains paint-wetting impairment substances1)
Electrical connection 1
Function Field device side
Connection type Socket
Connection technology Plug pattern H6, coded for motor
Degree of protection IP20 In assembled state
Electrical connection 2
Function Controller side
Connection type Cable
Connection technology Open end
1) PWIS = paint-wetting impairment substances
Tab. 3: Technical data