
Contents and general instructions
III
Festo P.BE−CPV−DI02−EN en 0704NH
Contents
Intended use VII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Target group VII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service VII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes on the use of this manual VIII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important user instructions IX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. InstallationCPV−DI02 and CPV−CS02 1−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 General instructions on installation 1−3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Electrical connecting and display elements 1−4. . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.1 Overview for setting the CPV Direct 1−5. . . . . . . . . . . . . . . . . . . . . . . . .
1.2.2 Setting the station number 1−7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.3 Setting the diagnostic mode (CPV−DI02)
or the load voltag monitoring (CPV−CS02) 1−9. . . . . . . . . . . . . . . . . . . .
1.2.4 Recognizing the CPI extension with the SAVE button 1−10. . . . . . . . . . .
1.2.5 Help table for setting the station number 1−10. . . . . . . . . . . . . . . . . . . .
1.3 Connecting the field bus 1−15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.1 Field bus cable 1−15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.2 Field bus baud rate and field bus length for PROFIBUS−DP
(CPV−DI02) 1−17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.3 Field bus interface 1−18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.4 Connectionpossibilities 1−20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4 Bus termination with termination resistors (CPV−DI02) 1−24. . . . . . . . . . . . . . . . .
1.5 Connecting the power supply 1−25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.1 Cable for power supply 1−25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.2 Selecting the power unit 1−27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.3 Connecting the power supply 1−29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6 Extending the CPV Direct 1−33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6.1 Rules for extending the CPI system 1−35. . . . . . . . . . . . . . . . . . . . . . . . .
1.7 Preparing the CPI system for commissioning 1−37. . . . . . . . . . . . . . . . . . . . . . . . .
1.7.1 Checking the CP strings 1−37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7.2 Saving the string assignment 1−38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8 Switching−on reaction of the CPI system 1−40. . . . . . . . . . . . . . . . . . . . . . . . . . . . .