Festo VABM-L1-***HWS1-***-GR Series Assembly instructions

Translation of the original instructions
1 Further applicable documents
All available documents for the product èwww.festo.com/pk.
Observe further applicable documents:
– Assembly instructions for separator VABD-...-B
2 Safety instructions
– Only assemble the product on components that are in a condition to be safely
operated.
– Do not interchange outputs 2 and 4 of the components during the mounting
procedure.
3 Product range overview
3.1 Included in delivery
1Manifold rail(1x)
VABM-L1-...HWS1/2-...-GR
2Blanking plug(1x)
3Plug module(1x)
Fig. 1
3.2 Not included in the delivery
4Supply plate
VABF-L1-...-P3A4-...-T1
5Cover plate VABB-L1-...-T
6Solenoid valve VUVG-...
Fig. 2
7Fixed flow restrictor VFFG-T-F...
8Check valve VABF-L1-...H-L2
9QS fitting
10 Electrical interface VAEM-L1-S-...
11 Blanking plug B-M7
12 Screw M5x16-A2-70-PRES-IP
Fig. 3
4 Mounting
4.1 Preparation
• Form pressure zones with the VABD-...-B
separatorè 1 Further applicable documents.
To feed additional operating pressure into the pressure zones or increase the
exhaust performance:
• Mount supply plate4 on manifold rail1.
In case of unused valve positions:
• Mount cover plates5.
4.2 Assembly of blanking plug/plug module
Fig. 4
• For dismounting of the plug module3, use the M4 thread (X).
With external pilot air:
• Push plug module3 into port 14 (A).
With internal pilot air:
1. Screw the blanking plug2 into the port 14 (A).
Tightening torque: 1.5 Nm – 20 %.
2. Screw both blanking plugsaA into the ports 14 (B).
4.3 Assembly of supply plate/cover plate/solenoid valve
Fig. 5
1. Place the components4/5/6 on the manifold rail1.
2. Tighten the screws (C).
VABM-L1- 10HWS 14HWS
(C) 0.3 Nm + 50 %0.55 Nm ± 50 %
Tab. 1
3. If applicable, place additional components4/5/6 as desired.
8080413
Manifold rail
VABM-L1-...HWS1/2-...-GR
8080413
2018-05a
[8080415]
Instructions|Assembly
Festo AG & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
[phone]
www.festo.com

4.4 Assembly of fixed flow restrictor/check valve/QS fitting
Fig. 6
1. Screw the QS fittings9 into channels 1, 3 and 5, as well as the ports 14 and
84.
2. Screw QS fittings9 into the respective outputs 2 and 4.
9M5 M7 GxG¼GÅ
[Nm] 1.5 – 30%1.5 – 20%5 – 20%8.5 ± 15%8.5 ± 15%
Tab. 2
3. Screw the fixed flow restrictors7/check valves8 into the channels 3 and 5
of the sub-base1 thereby forming a thread until they sit flush. When screw-
ing in again, use the threads already present.
VABM-L1- 10HWS 14HWS
72.0 Nm ± 15 %2.0 Nm ± 15 %
81.2 Nm ± 15 %2.0 Nm ± 15 %
Tab. 3
4.5 Assembly of electrical interface
NOTICE!
If the plug is bent during assembly, the function of the electrical interface can no
longer be guaranteed.
• Mount and plug the electrical interface parallel to the manifold rail.
Fig. 7
1. Place the electrical interfaceaJ on the manifold rail1.
2. Tighten the screws (D). Tightening torque: 0.7 Nm ± 20 %.
Screws (D): the variants VAEM-L1-S-M3-26/-50 only have 2screws each.
4.6 Assembly on the control cabinet
Fig. 8
1. Use control cabinet cut-out contour èwww.festo.com/sp.
2. Place the manifold rail1 on the control cabinet cut-out.
When degree of protectionIP 67 is not required:
1. Select ISO 4762 - M5 screws suitable for the installation situation.
2. Tighten the screws. Tightening torque: 3.5Nm±20%.
To comply with degree of protectionIP 67:
•Tighten screwsaB. Tightening torque: 4Nm±20%.
5 Earthing
Fig. 9
• Connect the earth terminal(E) to the earth potential. Shim the earthing
screw(G) with a toothed disc(F). The toothed disc(F) penetrates the anod-
ised coating of the manifold rail1. Earthing screw(G): M5x10.
ÄConductive connection established.