Friant MY-HITE FCNAHBT User manual

MY-HITE ADJUSTABLE TABLE
Model Number : FCNAHBT
Corner T Leg Base
ALL
WORKSTYLES
WELCOME
Please Read Instructions Before Use
ASSEMBLY INSTRUCTIONS

2
12
1.Read instructions
carefully. Check that no
parts are missing.
Single Sided
Wrench
Socket Head
Wrench
Electric Drill
Friant & Associates, LLC does not assume any responsibility for product that is altered in
any way.
2.Carefully identify each
component, especially
those that are similar.
The most common
mistake is mixing
up the order and
placement of parts.
IMPORTANT: When placing table in nal location, be sure there is
ample room for adjustment around ALL sides, and at the highest (50”)
and lowest (24.5”) points the table can reach. Make sure table will not
come into contact with any xed objects (xed tops, storage, shelving,
etc.) while adjusting.
Tools Needed
WARNING: Failure to follow the assembly instructions in this manual
can result in product damage, or personal injury.
Thank you for choosing Friant. We appreciate the trust and
condence you have placed in us and are committed to providing you
the best possible product.
Introduction
Friant offers a comprehensive line of ofce furniture for every space and requirement,
now including My-Hite, a height adjustable table that allows for standing or sitting
while working.
User Notes
1. As with all power-operated products, please follow instructions closely and handle
with care.
2. When moving My-Hite tables, please lift the tables, do not drag or tilt the table on
one leg as misalignment may occur
3. Check that the load on the table does not exceed limits (220lbs maximum on
straight, 330lbs maximum on corner).
4. The input voltage should be within 108-132V
5. Use the glides to properly level the table before use.Table should be level and aligned
at all times.
6. Before rst use, perform reset operation.
7. If, after trouble shooting the problem persists, contact Customer Service for further
assistance.

3
PART# IMAGE NAME PIECES
A Side Bracket 3
B Column Leg 3
CPad 1
D Crossbeam 3
E Center Rails 2
F Control Panel 1
G Control Box 1
HTelescopic Cover Plate 1
I Connector Wires 1 + 3
J, O Feet
3 feet or 2
feet & 1 post
foot
KSocket Button Head Bolt
M6*20mm 12
LSocket Button Head Bolt
M6*12mm 20
M Wire Manager 4
NTruss Head Screw
M5*20mm 34
Step 1: Place worksurface nished side down on a blanket.
Step 2: Insert Aside bracket into D crossbeam assembly. Repeat on other sides.
Step 3: Insert C pad under Bleg during assembly process for proper spacing.
D
CROSSBEAM
A
SIDE BRACKET
B
COLUMN LEG
WORKSURFACE
C
PAD
Parts List Installation Steps

4
A
B
K
SOCKET BUTTON
HEAD BOLT
M6*20mm
J
FOOT
Step 4: Use 4socket button head bolts, M6*12mm to secure side bracket, column leg and
crossbeam together as shown in detail.
Step 5: Remove C pad after leg installation, then reuse for assembly of other leg(s)
repeating steps 3 & 4. Remove pad when done.
Step 6: Attach Jfeet to Bcolumn leg with
K(4) socket button head bolts, M6*20mm.
Tighten bolts securely. Repeat step 6 with
other two legs
Step 7: Place all 3 leg assemblies on worksurface and insert Ecenter rails into D
crossbeams as shown. Hole on center rails should be centered between crossbeams.
Center leg assemblies on the worksurface. Make sure your overhang is even on all three
sides.
E
CENTER
RAILS
Base is: A - 40”-68”
B- 36”-54”
• Maximum recommended top: 54”x78”
• Minimum recommended top: 36”x40”
• Install My-Hite tops 4” from the back of the base when using 29”+
depth tops is recommended.
IMPORTANT: Make sure column legs are sitting perfectly at against the
worksurface
K
SOCKET BUTTON
HEAD BOLT
M6*20mm
O
POST FOOT
Step 6a: With option of Post foot: Attach
Opost foot to one column leg with K
(4) socket button head bolts, M6*20mm.
Tighten bolts securely. Repeat step 6
with other two legs.

5
Step 8: Secure Ecenter rails to D
crossbeams with L (8) socket button head
bolt M6*12mm.
N
TRUSS HEAD
SCREWS
M5*20mm
F
CONTROL
PANEL
Step 9 & 10: Ensure the leg assembly is still
centered, both side-to-side and front-to-back.
Secure the leg assembly to the worksurface
with N(12) truss head screws M5*20mm.
Secure the side bracket to the worksurface
with N12 truss head screws M5*20mm.
Step 8a: With option of post foot, as shown
below:
Step 9a: With option of post foot, as shown
below:
Step 11: Secure the Fcontrol panel in the
desired location with N(2) truss head screws
M5*20mm.
Step 11a: With post foot option as shown
below:
Step 12: Insert the Gcontrol box in-between
crossbeams. Connect Fcontrol panel to G
control box with Iconnector wires. as shown.
Use Mwire manager to secure Iconnector wires
to underside of worksurface.
Step 12a:With option of post foot, as
shown below:
G
CONTROL
BOX
I
CONNECTOR
WIRES
L
SOCKET BUTTON
HEAD BOLT
M6*12MM
E
CENTER
RAILS
D
CROSSBEAMS
N
TRUSS HEAD
SCREWS
M5*20MM
M
WIRE
MANAGER

6
Step 14: Turn table right side up, adjust the glides as necessary, and plug the power cord
into a 110v outlet.
Schematic view of the My-Hite wiring:
Step 13: Install the H telescopic cover plates,
leaving exit space for the electrical power
cords, and secure to worksurface with N (8)
truss head screws M5*20mm
Step 13a: With option of post foot, as shown
below:
Ensure the length of the plug-in cord is adequate to reach the outlet, as
well as the distance the table will travel up and down. Range: 24.5” at
lowest to 50” highest.
N
TRUSS HEAD
SCREWS
M5*20mm
H
TELESCOPIC
COVER PLATE

7
Error code Explanation Cause Solution
H01 Motor has
overheated
Overuse 1.
2.
3.
ERR,
ASR or
RST (solid
or ashing)
System is
locked
Various Reasons 1.
2.
3.
No display Control
Panel has
lost power
Disruption in
power supply to
base
1.
2.
3.
E01,
E02, or
E03
Excessive
weight
distribution
Too much
weight (limit
exceeded)
or
Other problem
1.
2.
3.
E07,
E08, or
E09
Signal
Interruption
Signal is
interrupted
between leg
and computer
1.
2.
CLEAR MAXIMUM & MINIMUM HEIGHT
SPECIAL CLEAR MINIMUM & MAXIMUM HEIGHT
Step 15: It is important to perform the reset
operation below before you use your My-
Hite table for the rst time.
FIRST TIME USE:
RESET OPERATION
1. Lower the table to 24.5” by holding arrow down (V) button. Release button.
2. Press the arrow down (V) button again and hold til ASR shows on the display.
3. Release the button and the ASR will ash on the display
4. Hold the arrow down button again. Table will shift up and down slightly as it resets to
24.5”.
SET MINIMUM HEIGHT
SET MAXIMUM HEIGHT
1. Press the arrow down (V) button to get to desired minimum height.
Note: the arrow down button must be the last button pressed to set the minimum height. Do not
press the arrow up button when trying to set the minimum height.
2. Hold “S” button till screen display ashes. Immediately press “S” button twice again.
3. Display will ash “000” and then show the set minimum height.
1. Press the arrow up (
V
) button to get to desired maximum height.
Note: the arrow up button must be the last button pressed to set the maximum height. Do not
press the arrow down button when trying to set the maximum height.
2. Hold “S” button til screen display ashes. Immediately press “S” button
twice again.
3. Display will ash “999” and then show the set maximum height.
TO PROGRAM THE MEMORY CONTROL PANEL:
Adjust the table to the desired height, press the Skey and one of the three preset
buttons. This position is now saved. Once a preset button is pushed, the table will
automatically move to the preset height. Repeat this procedure for each preset button.
NOTE : If you cannot lower the table to the 24.5” height to perform reset operation,
you may need to clear out the maximum and minimum height (See instructions
below). Once completed, please return to the Reset Operation instructions.
1. Table can be at ANY HEIGHT but NOT the minimum or maximum.
2. Hold “S” til display ashes. Release button.
3. Press “S” slowly, multiple times - until “555” shows on display.
Note: Display will show other codes, continue to press “S” until “555” shows.
4. Display will then show table height and can now move to any height between 24.5” and
50.1”.
1. Following is a special reset procedure when minimum and maximum height is set
within 1” of each other:
2. Unplug unit for 10 minutes
3. Connect unit to power take care not to touch up or down arrows
4. Hold S button until it ashes
5. Let go and press S button 6 times in a row
6. 555 will show up on the display, minimum and maximum heights are now cleared.
TROUBLESHOOTING MY-HITE
July 2019
1980 West Avenue, 140th, San Leandro CA 94577 TEL: [phone] FAX: [phone] http://www.friant.com