Frico Elztrip EZ106N User manual

Elztrip EZ100
600 - 1500 W
.... 7
SE
.... 17
DE
.... 15
RU
.... 11
NO .... 13 FR
.... 9
GB
.... 21
FI
.... 19
PL
Original instructions

Elztrip EZ100
2
L
[mm]
A
[mm]
EZ106N 870 655
EZ111N 1470 1252
EZ115N 1950 1731
1 2
EZMVK
EZ100
MÅTT

Elztrip EZ100
3
3 4
a < H
Dh = 1,5 - 2 m
EZ100
A 50
B 50
C 50
D 500
E1800
EZ106N 3,2 kg
EZ111N 5,4 kg
EZ115N 7,0 kg

Elztrip EZ100
4
Accessories
Type E-nr
(SE)
EL-nr
(NO)
HxWxD
[mm]
ERP 85 820 05 54 238 86 153x93x40
ERPS 85 820 10 54 328 90 153x93x40
T10S 85 809 33 54 911 12 80x80x31
TKS16 85 809 37 54 911 51 80x80x39
TD10 85 809 39 54 911 39 80x80x31
KRT1900 85 810 12 54 910 50 165x57x60
CIRT 85 702 92 54 325 39 155x87x43
Type EL-nr
(NO)
HxWxD
[mm]
EDM61 54 328 87 48x48x120
SSR30A 54 328 89 103x23x103
SSR50A 54 328 92 94x45x103
SSR70A 54 328 94 94x90x103
KRT1900
T10S TKS16
ERP
20
25
30
15
10
5
TD10
CIRT EDM61 SSR
CIRT
1
/
2
h
1 h
2h
4h
kW
SP
PV
MAN AT ALM
AUTO
MAN
WEST 6100+

Elztrip EZ100
5
Wiring diagrams
EZ1
230V ~
1
N
32
EZ1
K12U34U K GG
230V~
ERP
1
N
32
EZ1
1
N
32
EZ1
1
N
32
P
230V~
N
Thermostat
EZ1
1
N
32
EZ1
1
N
32
EZ1
1
N
32
EZ1
230V~
1
N
32
EZ1
1
N
32
EZ1
1
N
32
Control by thermostat
Output control
Internal wiring diagram
Output control with timer

Elztrip EZ100
6
Technical specifications
Type Heat
output
[W]
Voltage
[V]
Min.
cable
Ø
[mm2]
Dimensions
LxHxW
[mm]
Distance
between
brackets
[mm]
Max.
surface
temperature
[°C]
E-nr
(SE)
EL-nr
(NO)
EZ106N 600 230V~ 1.5 870x50x150 655 280 85 700 03 54 324 50
EZ111N 1050 230V~ 1.5 1470x50x150 1252 280 85 700 04 54 324 51
EZ115N 1500 230V~ 1.5 1950x50x150 1731 280 85 700 05 54 324 52
Protection class Elztrip EZ100: (IP44), splash-proof design.
Approved by SEMKO and CE compliant.

Elztrip EZ100
9
GB
General Instructions
Read these instructions carefully before
installation and use. Keep this manual for
future reference.
The guarantee is only valid if the units
are used in the manner intended by the
manufacturer and in accordance with the
Frico mounting and operating instructions.
Application area
Elztrip EZ100 has a single heating panel and
is designed for ceiling heights between 2.5 and
4 metres. EZ100 is used in shops, schools,
exhibition halls, workshops and hospitals.
Private homes and offices are also common
areas of use.
EZ100 is suitable both for total and
supplementary heating, as well as for
protection against cold draughts from large
glass surfaces. Protection class: IP44.
Operation
The panels have an operating temperature of
up to 280oC and the heat is radiated to cold
surfaces. Heating with radiant heaters is very
energy effecient and a high comfort level is
obtained.
Mounting
Elztrip EZ100 is mounted on the ceiling, on
armature rails or suspended from the ceiling
by means of rods or chains. EZ100 is intended
for permanent installation and should always
be mounted horizontally.
In rooms frequently used, the heater should
be mounted 1.5 to 2 metres above head
height, see Fig. 3. The distance between the
panels should not be more than the height
between panel and floor, i.e ”a” should be less
than ”H” , see Fig.3. For minimum mounting
distance, see Fig.4.
Ceiling fixtures and screws are found inside
the connection box.
Mounting on the ceiling
1. Mount the ceiling fixtures on the ceiling.
2. Open the folded mounting hinges on the
top side of the heater and hang the heater
on the ceiling fixtures. See Fig. 1. Make sure
that the guide pegs are fitted into the holes, to
ensure that the heater is fixed in a horizontal
position. Fasten the screws.
Mounting on the wall (only horizontal)
Brackets for wall mounting (EZMVK) are
extra.
1. Mount the bracket on the wall.
2. Open the folded mounting hinges on the
top side of the heater and hang the heater
on the brackets. See Fig. 2. Make sure that
the guide pegs are fitted into the holes, to
ensure that the heater is fixed in a horizontal
position. Fasten the screws.
Connection
The terminal box cover has self-tapping
screws. The screw should only be unthreaded
1,5 turns, after which the cover can be
removed. NB While the screw is self-tapping,
the thread is vunerable to damage if the screw
is fully removed and replaced several times.
EZ100 is intended for 230V~ and permanent
installation. The heater(s) should only be
wired by a competent electrician, and in
accordance with existing national regulations.
The appliance should be preceded by
a double pole switch with at least 3 mm
breaking gap. There are two holes with cable
glands Ø 21mm on the top of the connection
box. Connection and serial connection of
EZ100 is done with a maximum cable size of
4x2.5 mm2 + earth.
Start up (E)
When the unit is used for the first time or
after a long period of disuse, smoke or odour
may result from dust or dirt that has collected
on the element. This is completely normal
and disappears after a short time.
Installation and operating instructions

Elztrip EZ100
10
GB
Residual current circuit breaker (E)
When the installation is protected by means
of a residual current circuit breaker, which
trips when the appliance is connected,
this may be due to moisture in the heating
element. When an appliance containing a
heater element has not been used for a long
period or stored in a damp environment,
moisture can enter the element.
This should not be seen as a fault, but is
simply rectified by connecting the appliance
to the mains supply via a socket without a
safety cut-out, so that the moisture can be
eliminated from the element. The drying
time can vary from a few hours to a few days.
As a preventive measure, the unit should
occasionally be run for a short time when it is
not being used for extended periods of time.
Maintenance
There might be a rattling noise the first time
of use when the surface coating of the panels
is settling.
If the heater is used in rooms where there
are aerosols, lacquer, solvents and similar,
this can cause a coating on the panels and
discolour them. The output is not affected.
In all electrical heating appliances, small
clicks can occur due to movement when the
material expands and contracts with changes
in temperature.
Safety
• For all installations of electrically heated
products should a residual current
circuit breaker 300 mA for fire protection
be used.
• Do not touch surface of heater when in
use!
• The unit must not be covered fully
or partially with clothes or similar
materials, as covering can result in a risk
of fire!
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved. Children shall not play with
the appliance. Cleaning and user
maintenance shall not be made by
children without supervision.

Art.nr 208956, 130611 HH/SÄ
Main office
Frico AB Tel: [phone]
Box 102
SE-433 22 Partille [email protected]
Sweden www.frico.se
For latest updated information and information
about your local contact: www.frico.se