Furuno VR-7000 User manual

VOYAGE DATA RECORDER (VDR)
VR-7000/VR-7000S
OPERATOR'S MANUAL
www.furuno.com
Model
SIMPLIFIED VOYAGE DATA
RECORDER (S-VDR)

・FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomi a, 662-8580, JAPAN
A
:
JUL
2014
.
Printed in Japan
All rights reserved.
R1
:
JAN
.
10, 2023
Pub. No.
OME-44850-R1
(
REFU
)
VR-7000/7000
0 0 0 1 9 7 2 0 4 1 5

i
IMPORTANT NOTICES
General
• This manual has been authored with simplified grammar, to meet the needs of international users.
• The operator of this equipment must read and follow the instructions in this manual.
Wrong operation or maintenance can void the warranty or cause injury.
• Do not copy any part of this manual without written permission from FURUNO.
• If this manual is lost or worn, contact your dealer about replacement.
• The contents of this manual and the equipment specifications can change without notice.
• The example screens (or illustrations) shown in this manual can be different from the screens you
see on your display. The screens you see depend on your system configuration and equipment
settings.
• Save this manual for future reference.
• Any modification of the equipment (including software) by persons not authorized by FURUNO will
void the warranty.
• The following concern acts as our importer in Europe, as defined in DECISION No 768/2008/EC.
- Name: FURUNO EUROPE B.V.
- Address: Siriusstraat 86, 5015 BT, Tilburg, The Netherlands
• The following concern acts as our importer in UK, as defined in SI 2016/1025 as amended SI 2019/
470.
- Name: FURUNO (UK) LTD.
- Address: West Building Penner Road Havant Hampshire PO9 1QY, U.K.
• All brand, product names, trademarks, registered trademarks, and service marks belong to their
respective holders.
How to discard this product
Discard this product according to local regulations for the disposal of industrial waste. For disposal in
the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the
correct method of disposal.
How to discard a used battery
Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter
on Maintenance. If a battery is used, tape the + and - terminals of the battery before disposal to pre-
vent fire, heat generation caused by short circuit.
In the European Union
The crossed-out trash can symbol indicates that all types of batteries
must not be discarded in standard trash, or at a trash site. Take the
used batteries to a battery collection site according to your national
legislation and the Batteries Directive 2006/66/EU.
In the USA
The Mobius loop symbol (three chasing arrows) indicates that
Ni-Cd and lead-acid rechargeable batteries must be recycled.
Take the used batteries to a battery collection site according to
local laws.
In the other countries
There are no international standards for the battery recycle symbol. The number of symbols can in-
crease when the other countries make their own recycle symbols in the future.
Cd
Ni-Cd Pb

ii
SAFETY INSTRUCTIONS
WARNING WARNING
ELECTRICAL SHOCK HAZARD
Do not open the equipment.
Only qualified personnel should work
inside the equipment.
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury
can result.
Immediately turn off the power
(BATTERY and AC switches in that
order) at the DCU and also turn off
the power at the ship's mains
switchboard if water leaks into the
equipment or the equipment is
emitting smoke or fire.
Continued use can cause fatal
damage to the equipment.
Do not disassemble the DRU.
The important data is saved to the
DRU. To prevent the loss of data, do
not disassemble the DRU.
Do not allow rain or water splash
to contact the equipment.
Fire or electrical shock can result.
Do not disassemble the battery in
the DCU.
Battery fluid is harmful to the eyes
and skin, particularly the eyes. If the
fluid contacts skin or eyes, flush area
with fresh water and contact a
physician immediately.
Do not dispose of the battery or
acoustic beacon of the Fixed DRU
in fire.
Those components may burst if
disposed of in fire. Further, dispose
of the battery in accordance with
appropriate regulations.
Do not touch any electrically
conductive parts.
Touching electrically conductive
parts can result in electrical shock.
Use rubber gloves, etc. when
conducting inspection or
maintenance work.
Do not short battery terminals.
Short can lead to bursting or fire.
Indicates a condition that can cause death or serious
injury if not avoided.
Indicates a condition that can cause minor or moderate
injury if not avoided.
WARNING
CAUTION
Warning, Caution Prohibitive Action Mandatory Action
Use the correct fuse.
A wrong fuse can cause fire or
serious damage to the equipment.

SAFETY INSTRUCTIONS
iii
CAUTION
Do not:
- use batteries of different capacities
- mix old batteries with new
- mix batteries of different makes
The battery of the DCU and Float-free
DRU have multiple cells. Batteries
themselves may become damaged or
damage to electrical parts may result.
WARNING
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
WARNING LABELS
Warning labels are attached to the DCU.
Do not remove the labels. If the label is missing or damaged, contact a FURUNO agent or
dealer about replacement.
Name: Warning Label 1
Type: 86-003-1011-3
Code No.: 100-236-233-10
About the TFT LCD
The TFT LCD is constructed using the latest LCD techniques, and displays
99.99% of its pixels. The remaining 0.01% of the pixels may drop out or
blink, however this is not an indication of malfunction.
Do not connect/disconnect the cable
while turning the power on.
The unit may be damaged.
WARNING
Do not wet the capsule of the
Float-free DRU.
The wetted capsule may
accidentally transmit a signal.
Do not approach the antenna of
the Float-free DRU.
The antenna of the Float-free DRU
emits electromagnetic radio
frequency (RF) that can be harmful
to the human body. Distance at
which RF radiation level of 100 and
10 W/m
2are given in the table
below.
100W/m2
10W/m2
0.16m
0.48m
IEC60945
IEC60945
RF power density Distance Description
required by

iv
TABLE OF CONTENTS
FOREWORD ...................................................................................................................vi
SYSTEM CONFIGURATION ........................................................................................viii
1. OPERATION ..........................................................................................................1-1
1.1 Overview .................................................................................................................... 1-1
1.2 Operating Procedure.................................................................................................. 1-5
1.2.1 How to turn the power on then record the data.............................................. 1-5
1.2.2 How to stop recording .................................................................................... 1-6
1.3 Operation on Remote Alarm Panel ............................................................................ 1-6
1.3.1 Start screen and base screen ........................................................................ 1-6
1.3.2 Controls.......................................................................................................... 1-7
1.3.3 How to adjust the brilliance of the LCD and keys........................................... 1-7
1.3.4 Main menu overview ...................................................................................... 1-8
1.3.5 How to extract the recorded data to an external media ...............................1-12
1.3.6 How to record the data to a USB flash memory........................................... 1-15
1.3.7 How to execute SAVE function for recorded data (only for VR-7000S)....... 1-15
1.3.8 Brilliance sharing function ............................................................................ 1-16
1.4 Alerts ........................................................................................................................ 1-17
1.4.1 What is an alert? .......................................................................................... 1-17
1.4.2 Alert list ........................................................................................................ 1-18
1.4.3 Alert icons and their meanings..................................................................... 1-19
1.5 How to Release the Fixed DRU ............................................................................... 1-19
1.6 How to Release the Capsule from the Bracket of the Float-free DRU in Emergency
Situation ................................................................................................................... 1-19
2. MAINTENANCE .....................................................................................................2-1
2.1 General Maintenance and Cleaning........................................................................... 2-1
2.2 Maintenance of the Float-free DRU ........................................................................... 2-2
2.2.1 Notice for the maintenance and self test........................................................ 2-2
2.2.2 Monthly maintenance ..................................................................................... 2-4
2.2.3 Normal self test .............................................................................................. 2-6
2.2.4 Extended self test .......................................................................................... 2-8
2.2.5 Annual Performance Test for the Float-free DRU........................................ 2-10
2.2.6 Shore-Based Maintenance (SBM) ...............................................................2-10
2.3 Annual Recertification .............................................................................................. 2-11
2.4 Fuse Replacement ................................................................................................... 2-12
2.5 Consumable Parts.................................................................................................... 2-13
2.6 Self Test ...................................................................................................................2-13
2.7 Verification of Recording Function of the Long Term Device................................... 2-15
3. TROUBLESHOOTING ...........................................................................................3-1
3.1 General Troubleshooting............................................................................................ 3-1
3.2 Alert List ..................................................................................................................... 3-1
3.2.1 Alert list for BAM mode .................................................................................. 3-1
3.2.2 Alert list for Legacy mode............................................................................... 3-8
4. REMOTE PLAYBACK FUNCTION (LAND-SHIP COMMUNICATION) ................4-1
4.1 Preparations............................................................................................................... 4-1
4.2 Limitations and Notifications ...................................................................................... 4-1
4.3 Recommended Network Construction ....................................................................... 4-2

TABLE OF CONTENTS
v
APPX. 1 MENU ITEMS.............................................................................................AP-1
APPX. 2 PARTS LIST/LOCATION ..........................................................................AP-2
APPX. 3 LIST OF TERMS AND ABBREVIATIONS/SYMBOLS .............................AP-5
APPX. 4 PLAYING BACK RECORDED DATA .......................................................AP-7
SPECIFICATIONS ..................................................................................................... SP-1

vi
FOREWORD
A Word to the Owner of the VR-7000/7000S
Congratulations on your choice of the FURUNO Voyage Data Recorder (VDR) VR-7000/Simpli-
fied Voyage Data Recorder (S-VDR) VR-7000S. We are confident you will see why the FURUNO
name has become synonymous with quality and reliability.
Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for innovative and
dependable marine electronics equipment. This dedication to excellence is furthered by our ex-
tensive global network of agents and dealers.
Your equipment is designed and constructed to meet the rigorous demands of the marine envi-
ronment. However, no machine can perform its intended function unless properly installed and
maintained. Please carefully read and follow the operation and maintenance procedures set forth
in this manual.
We would appreciate feedback from you, the end-user, about where we are achieving our purpos-
es.
Thank you for considering and purchasing FURUNO equipment.
What is a VDR?
A VDR records various data and events encountered aboard ship. The purpose of the VDR is to
help investigators locate the causes of marine incidents.
The revised SOLAS Chapter V requires the installation of VDRs on passenger ships of 150 GT
and above on all voyages and other ships of 3000 GT and above on international voyages and for
newly built ships on and after 1 July, 2002.
The basic VR-7000/7000S consists of a Data Collecting Unit (DCU), a Data Recording Unit
(DRU), a Remote Alarm Panel (RAP), a video LAN converter, a sensor adapter and microphones
to record bridge audio. A Junction Box (JB) is optional. The DCU contains the Data Processor
Unit, interface modules and backup batteries. It collects data from sensors as required by the IMO
and IEC standards. The DCU processes the incoming data and information in the order of occur-
rence while old data is overwritten with new data for storage in the DRU for 48 hours. The batteries
supply power to the DCU to record bridge audio for two hours in case of a ship’s mains power
failure.
The flash memory in the DRU stores the data coming from the DCU. All essential navigation and
status data including bridge conversation, VHF communications, and radar images are recorded.
The data can be retrieved by using playback software for investigation after an incident.
The Fixed DRU* components are embodied in a protective capsule. The capsule ensures survival
and recovery of the recorded data after an incident. An acoustical pinger helps locate the Fixed
DRU underwater.
The capsule of the Float-free DRU* is stored in the bracket. When the Float-free DRU sinks to
depths of up to four meters, the capsule automatically comes off from the bracket then floats on
the sea surface. At the same time, the capsule starts to transmit 406 MHz signal for locating the
position of capsule and 121.5 MHz signal for homing for at least 168 hours.
*: Select one for VR-7000S.

FOREWORD
vii
Features
The main features of the VR-7000/7000S are as shown below.
Program No.
• VR-7010 DCU: 2450102-01.XX • VR-7017 RAP: 2450103-01.XX
XX: Minor change (For VR-7000S, XX is 10 or after for DCU, 06 or after for RAP.)
Note: When the VDR program version is “01.20” or later, Live Player V5 program version should
be “01.10” or later. When the VDR program version is “01.20” or earlier, Live Player V5 program
version should be “01.20” or earlier.
Fonts
The “iwata open type” font is used for the Remote Alarm Panel VR-7017.
Open Source Software
This product includes software to be licensed under the GNU General Public License (GPL), GNU
Lesser General Public License (LGPL), BSD, MIT and others. For details about the term of use
for these software, see the OSS license list on the supplied program CD (directory: \OSS_Li-
censeList\vdr).
The program(s) is/are free software(s), and you can copy it and/or redistribute it and/or modify it
under the terms of the GPL or LGPL as published by the Free Software Foundation. Please ac-
cess to the following URL if you need source codes: https://www.furuno.co.jp/cgi/cnt_oss_e01.cgi
Reverse engineering
Reverse engineering (disassemble, decompile) of the software of this equipment is strictly prohib-
ited. However, reverse engineering is permitted under the following conditions:
Disclosure of Information about China RoHS
With regards to China RoHS information for our products, please refer to our website
(www.furuno.com).
• Color LCD with remote alarm panel.
• Complies with the following standards:
• VR-7000: IEC 61996-1 Ed.2.1, IEC 61162-1 Ed.5.0, IEC 61162-2 Ed.1.0, IEC 61162-450 Ed.2.0,
IEC 62288 Ed.2.1, IEC 60945 Ed.4.0, IEC 61924-2 Ed.1.0, IEC 62923-1/2 Ed.1.0
• VR-7000S: IEC 61996-1 Ed.2.1, IEC 61996-2 Ed.2.0, IEC 61162-1 Ed.5.0, IEC 61162-2 Ed.1.0,
IEC 61162-450 Ed.2.0, IEC 62288 Ed.2.0, IEC 60945 Ed.4.0, IEC 62923-1/2 Ed.1.0
• Reliable and fast data exchange between DCU and DRU via Ethernet.
• Fixed DRU and Float-free DRU with 48 hours recording.
• Compatible with remote maintenance.
• Recorded data can be analyzed and monitored on shore.
• Software updating from a PC connected to Ethernet.
• Long term device for storage (VR-7000: 720 hours recording, VR-7000S: 48 hours recording) and
retrieval of data.
• The library used for the reverse engineering (GNU Library General Public License Version 2, GNU
Lesser General Public License Version 2.1, or later editions) is clearly noted.
• The reverse engineered software is used only within the scope outlined under the appropriate li-
cense.

viii
SYSTEM CONFIGURATION
Basic configuration is shown with solid line.
Environmental category
All units (other than VR-7021F/7024F, VR-7022F, VR-
7012W and VR-7020)
Protected from the weather
VR-7021F/7024F Portable
VR-7022F, VR-7012W, VR-7020 Exposed to the weather
Data
Collecting
Unit (DCU)
VR-7010
Fixed Data Recording Unit (Fixed DRU)
VR-7020*
3
Float-free Data Recording Unit
(Float-free DRU)
VR-7021F/7024F*
3
Video LAN Converter
IF-7100
24 VDC
PC
Live Player V5
VR-7030
100-230 VAC
Remote Alarm Panel
VR-7017*
1
Microphone
VR-7011
Waterproof Microphone
VR-7012W
Max. 8 units
Radar/ECDIS display 100-230 VAC
100-230 VAC
Max. 2 units
Radar, ECDIS, etc.
VHF Audio
- Serial Interface: Max. 2 ch
(IEC 61162-1/2)
- Serial Interface: Max. 6 ch
(IEC 61162-1)
Intelligent HUB
HUB-3000
*4
Sensor Adapter
MC-3000S
Sensor Adapter
MC-3010A
Sensor Adapter
MC-3020D
Serial Interface
Analog Interface
Digital IN Interface
Junction Box
VR-7022F*
3
Network
Equipment
Power Supply Unit
PSU-011*
2
Junction Box
IF-8540
or
IF Signal
*
1
: Nominal viewing distance: 0.5 m
*
2
: For Russian vessel only.
*
3
: When using the VR-7000S, select either the
“VR-7020” or the “VR-7021F/7024F and
VR-7022F”.
*
4
: Use Switching HUB (HUB-100) for
IEC61162-450 Ed.1 compliant network.
Max. 2 units
Intelligent HUB
HUB-3000
*4

1-1
1. OPERATION
1.1 Overview
The VR-7000/7000S consists of a Data Collecting Unit (DCU), Data Recording Units
(Fixed DRU and Float-free DRU), Remote Alarm Panel (RAP), Video LAN Converter,
Sensor Adapter and bridge microphone units. The VDR system continuously stores
data for 48 hours onto the Flash Memory in the capsule, erasing the oldest data stored
as new data is recorded. The VDR mainly records the sentences shown in the table
below.
Main sentences to be recorded
Power supply precaution
If ship’s mains power source (100-230 VAC) and emergency source fail, the VR-7000/
7000S continues to record bridge audio for two hours from backup batteries.
Continuity of storing data
The VDR should be provided with power to store data for over 48 hours (for Fixed DRU
and Float-free DRU) or over 720 hours (for long term device of the DCU) on a first-in,
first-out basis. Recording is terminated only under the following conditions:
• During essential maintenance while the vessel is in port.
• When the vessel is laid-up.
Data to be recorded IEC 61162 formatter
Date and time ZDA
Ship’s position and datum used GNS and DTM
Speed (water and/or ground) VBW
Heading (true) HDT
Heading (magnetic) HDG
AIS-VHF data-link message VDM
AIS-VHF data-link own-vessel message VDO
Depth (echo sounder) DPT
Alerts and Alarms ACN, ALC, ALF, ALR
Rudder sensor angle RSA
Rudder order status ROR
Heading/track control command HTC
Heading/track control data HTD
Engine order/response RPM, XDR
Hull openings, watertight doors XDR
Accelerations and hull stress HSS, XDR
Wind speed and direction MWV
VDR alert output ALF, ALC
Heartbeat supervision sentence HBT

1. OPERATION
1-2
Data Collecting Unit
The DCU mainly consists of a Data Processor Unit and Power Control Panel. The
DCU includes batteries with a lifetime of approximately four years. The DCU collects
the data from various sensors radar/ECDIS and records them in the Fixed DRU, Float-
free DRU and internal long term device.
Recording interval of data and audio is as follows:
• Radar/ECDIS video signal: every 15 seconds
• Bridge and VHF audio: real time
• IEC sentences: when received
• Analog and digital data: every second
For VR-7000, you can select one or two 512-GB SSD(s) as internal long term de-
vice(s). When selecting one SSD, you can add another one using an optional SSD kit
later.
*: The recording interval for 3 channels is 15 seconds, which is compliant with
IEC61996-1 Ed.2.1 and IEC61996-2 Ed.2.0. Other channels record a maximum of
four video signals at intervals of 15 seconds, using the time-division method.
For VR-7000S, there are four save areas (Area1, 2, 3, 4) in the long term device(s).
Each area can record data for 12 hours.
Data Recording Unit
Fixed DRU
The Fixed DRU is housed in a highly visible protective capsule which can withstand a
fire of 1,100°C for one hour and deep-sea pressure of 6,000 m.
The underwater acoustic beacon (pinger) on the capsule automatically transmits 10
ms pulses at 37.5 kHz for at least 90 days when it is submerged in water. The expect-
ed life of the beacon battery is three years.
Float-free DRU
The capsule of the Float-free DRU has the same functionality of an satellite EPIRB
(Emergency Position-Indicating Radio Beacon). The VDR data is recorded in the stor-
age module at the bottom of capsule.
The DCU feeds the VDR data to the bracket of the Float-free DRU through the LAN
cable, then the bracket feeds the data to the capsule by wireless communication.
The capsule of the Float-free DRU is stored in the bracket. When the Float-free DRU
sinks to depths of up to four meters, the capsule is automatically released from the
bracket then floats to the sea surface. At the same time, the capsule starts to transmit
406 MHz signal for locating the position of capsule, 121.5 MHz signal for homing and
AIS messages (VR-7024F only) for at least 168 hours.
Note: Select fixed DRU or float-free DRU for VR-7000S.
No. of pcs Storage time Video signal channels recorded at the same time
1 SSD (512 GB) 720 hours Up to 5 channels*
2 SSDs (1 TB) Up to 6 channels*

1. OPERATION
1-3
Data items to be recorded
Note: If the sensor data is input to the DCU through an external unit (sensor adapter,
junction box, etc.), the input of the sensor data is delayed because of the communica-
tion lag between the DCU and external unit.
Date and time: Date and time are obtained from an external GPS navigator refer-
enced to UTC. When an external GPS navigator is not available, a signal is recorded
with a built-in clock in the DCU.
Ship’s position and datum used: Latitude, longitude and datum are obtained from a
GPS navigator, Loran-C receiver or other EPFS or INS available on standard serial
interface. The source of data is identifiable on playback.
Speed (water and/or ground): Speed through the water (STW) or speed over the
ground (SOG) is recorded. The resolution is 0.1 kn. Transverse speed is also indicat-
ed when available on board.
Heading (true, magnetic): Heading is recorded to a resolution of 0.1°. The data is la-
beled G (gyrocompass), GPS, GLONASS, MAG. If heading information is not avail-
able in IEC 61162 format, an appropriate interface may be necessary.
Depth (echo sounder): Depth under keel up to a resolution of 0.1 m as available on
the ship is recorded.
Alarms: The status of all IMO mandatory alarms is recorded individually with ID num-
ber and time stamp. Audible alarms from the alarm units are stored simultaneously by
the bridge audio microphones.
Rudder order/response: Rudder order and response angles are recorded up to a
resolution of 1° as available on the ship. The rudder information is recorded. If more
than one rudder is provided, the circuitry can be duplicated.
Engine order/response: The DCU obtains the engine order and response from the
engine telegraph or direct engine control. The engine parameters with shaft revolution
and ahead/astern indicators are recorded to a resolution of 1 rpm.
All order and response from bow, stern, thruster, tunnel thrusters and controllable
pitch propellers shall be recorded.
Hull openings, watertight doors: Digital and serial signals can be input individually.
The data is stored with time stamps.
Accelerations and hull stresses: The DCU obtains signals from appropriate hull
stress and response monitoring devices. The inputs are recorded individually and
stored with time stamps.
Wind speed and direction: The DCU obtains the signal from appropriate wind speed
and direction sensor. The inputs are recorded individually and stored with time
stamps. The wind speed resolution is 1 unit (1 kn, 1 m/s, etc.). The wind direction res-
olution is 1°.
VDR alarm output: If, as an option, such messages are sent then the appropriate
sentence formats are ALF and ALC.
Radar/ECDIS data: Radar/ECDIS image is recorded in the Fixed DRU, Float-free
DRU and long term device via the LAN or the video LAN converter. Range rings,
EBLs, VRMs, plotting symbols, radar maps, parts of SENC, voyage plan, and other
essential navigational indications are included in the recorded radar image. Own

1. OPERATION
1-4
ship’s mark and position (latitude and longitude), course, speed, voyage plan, and oth-
er essential navigational indications are included in the recorded ECDIS image. One
complete picture frame is captured at intervals of 15 s. Scanning may be interlaced or
non-interlaced.
The channel number and resolution can be recorded is shown in the table below.
*: Recorded to the long term device (SSD) only. Not recorded to the Fixed DRU and
Float-free DRU.
Bridge audio: Up to eight microphones are supplied as standard to record conversa-
tion at conning station, radar display and chart table. Microphone captures conversa-
tion in the bridge, audio signals from equipment and sound from machinery. The
microphone generates a test beep every 12 hours which is also recorded. The micro-
phone picks up audio signals ranging from 150 to 6000 Hz.
Communications audio: A maximum of two VHF communications are recorded for
both transmitted and received audio signals.
Minimum data retention period
The VDR data is retained in the recording media, following termination of recording.
The minimum data retention periods for each recording unit are shown in the table be-
low (IEC61996-1/IEC61996-2 compliant).
Input method No. of pcs Resolution/Max. channel number
Inputs through
the video LAN
converter
1 SSD
(512 GB)
UXGA (16001200): 2 ch + Full HD (19201080): 1 ch
2 SSDs
(1 TB)
UXGA (16001200): 2 ch + Full HD (19201080): 1 ch +
WUXGA (19201200): 1 ch*
IEC61162-450
format
1 SSD
(512GB)
For PNG format:
UXGA (16001200): 2 ch + Full HD (19201080): 1 ch
For JPEG format (quality is 50 or above):
WUXGA (19201200): 3 ch
For JPEG format (quality is less than 50):
WUXGA (19201200): 5 ch
2 SSDs
(1TB)
For PNG format:
UXGA (16001200): 2 ch + Full HD (19201080): 1 ch +
WUXGA (19201200): 1 ch*
For JPEG format (quality is 50 or above):
WUXGA (19201200): 3 ch + WUXGA (19201200): 1 ch*
For JPEG format (quality is less than 50):
WUXGA (19201200): 5 ch + WUXGA (19201200): 1 ch*
Unit Minimum Data Retention Period
Long term device (DCU) 2 years after recording
Fixed DRU
Float-free DRU 6 months after recording

1. OPERATION
1-5
1.2 Operating Procedure
1.2.1 How to turn the power on then record the data
Data Collecting Unit
To start recording, open the DCU door with its key and turn on the AC and BATTERY
switches in that order on the power control panel. Confirm that the AC SUPPLY
MAINS LED and BATTERY BACKUP LED on the power control panel light. Data is
automatically recorded in the Fixed DRU*, Float-free DRU* and long term device.
*: Select one for VR-7000S.
Note 1: When turning the power on at temperatures of 0 °C or lower, the DCU must
be warmed before it can be operated, which takes a maximum of 30 minutes. The er-
ror message may appear on the screen of the VR-7017, however, this is not abnormal.
Note 2: If the VR-7000/7000S system fails to start, it may be restarted.
Note 3: Do not turn off the DCU power for 30 seconds after the power is turned on.
Recorded data can be corrupted.
Note 4: Do not exert force on the opened DCU door. Force can damage the door.
Note 5: Do not connect multiple USB flash memories to the USB port via s USB HUB.
Video LAN Converter (IF-7100)
The video LAN converter converts the radar video signal to the LAN signal.
Turn the power on/off for the IF-7100 and the equipment connected to the IF-7100 (i.e.
processor unit for radar or ECDIS) in the following order. Otherwise the IF-7100 may
not function properly.
Power-on: Turn on the IF-7100 and the connected equipment in that order.
Power-off: Turn off the connected equipment and the IF-7100 in that order.
Note: The IF-7100 does not have a power switch. Turn off the IF-7100 from the main
switchboard.
NOTICE
Do not open the DCU door unless authorized to do so.
The DCU comes with a key to protect against any unauthorized
access. The key must be kept securely by authorized personnel.
DCU Power control panel
BATTERY switch
AC switch
BATTERY BACKUP LED
(BATT BACK UP)
SYSTEM FAIL LED
(SYS FAIL)
AC SUPPLY MAINS LED
(AC MAINS)
USB port
(See paragraph 1.3.7.)

1. OPERATION
1-6
1.2.2 How to stop recording
Recording is terminated only under the following conditions:
• During essential maintenance while the vessel is in port.
• When the vessel is laid-up.
To stop recording, open the DCU door with its key and turn off the BATTERY and AC
switches in that order. DO NOT turn off the system by the main breaker while the BAT-
TERY switch is on. If only the AC switch is turned off, the system operates on the bat-
teries. The system stops after recording the audio data only for two hours. When the
AC power is supplied to the DCU again, the batteries are charged. The BATTERY
BACKUP LED flashes while charging the batteries.
Note: After the power to the DCU is turned off, wait at least 10 seconds before reap-
plying the power. The DCU may not function correctly.
1.3 Operation on Remote Alarm Panel
1.3.1 Start screen and base screen
No power switch is provided on the Remote Alarm Panel; it is turned on and off by the
power switch on the DCU. After the boot program screen appears, the start screen ap-
pears followed by the base screen.
Note: When the DCU does not boot normally, it takes a maximum of 10 minutes to
display the base screen. The error message “Lost DCU” (“No DCU connection” for
Legacy mode) appears on the screen.
Start screen
Base screen for VR-7000
VR-7017
REMOTE ALARM PANEL
Base screen for VR-7000S
[MENU / ESC] : List [ENT] : - - - ▲ /
▼
/
◄
/
►
: Brill
VR -7000
[MENU / ESC] : List [ENT] : - - - ▲ /
▼
/
◄
/
►
: Brill
VR -7000 S
“Press MENU, then ENT to save recorded data.”
VR -7017 VDR REMOTE ALARM PANEL
VR -7017 SVDR REMOTE ALARM PANEL

1. OPERATION
1-7
1.3.2 Controls
1.3.3 How to adjust the brilliance of the LCD and keys
1. Press the BRILL key to show the [BRILL] setting window.
2. To adjust the brilliance, use the cursorpad; or for the LCD, or for the
keys.
3. Press the ENT or MENU/ESC key to close the setting window.
Control Function
BRILL Short press: Displays the [BRILL] setting window.
Long press: Restores the brilliance of the LCD and keys to
default.
ACK BAM mode: Not used.
Legacy mode: Acknowledge an alert to stop the flashing of
the alert list and silence the alert buzzer.
TEST Opens the test menu.
Extract Extracts the recorded data to the external media.
MENU/ESC Short press: Opens/closes the menu, returns one layer in
menu operation.
Long press: When one ore more alerts are active, opens the
alert list. When no active alert exists, returns to the base
screen except in pop-up displays (e.g. key beep, extraction re-
lated, etc.) and tests.
ENT • Confirms a selection.
• Legacy mode only: Silences the alert buzzer temporarily
when there are unacknowledged alerts. (The alert buzzer
sounds again in 30 seconds after the buzzer stops.)
Cursorpad
Short press: Selects a menu item, switches the page, adjusts
the brilliance of the LCD and keys when the [BRILL] setting
window opens.
Long press: Moves the cursor continuously.
BRILL
ENT
MENU
ESC
TEST
Extract
ACK
BRILL
ACK
TEST
Extract
MENU
ESC
ENT
Setting ranges: 0 to 7
Defaults: 5
BRILL
LCD Min
Min
Max
MaxKe
y
5
5
◄►
▼▲

1. OPERATION
1-8
1.3.4 Main menu overview
1. Press the MENU/ESC key to
open the main menu on the
base screen or alert list.
2. Use the cursorpad (or )
to select a menu item then
press the ENT key.
[Serial Monitor]
You can monitor the sensor information input to the serial channels.
To see the information for a serial channel, use the cursorpad to select a serial chan-
nel (SI01 to SI16) then press the ENT key to show the serial monitor screen. The latest
received data is displayed on the top of the screen.
Note: A serial channel whose number is SI17 or later is no use.
Press the ENT key to stop the serial display. To restart the serial display, press the
ENT key again.
Execute SAVE Function
Serial Monitor
Sensor(LAN)Monitor
Analo
g
Monitor
Di
g
ital Monitor
Ima
g
e Ca
p
ture Status
Audio Monitor
Life Parts List
Status Monitor
Settings
Only for VR-7000S
To shift the page,
use the cursorpad
(◄ or ►).
Serial Channel Select
◄
1 (SI01 - SI30)
►
SI11:XXXXX
SI12:XXXXX
SI13:XXXXX
SI14:XXXXX
SI15:XXXXX
SI16:XXXXX
SI17:XXXXX
SI18:XXXXX
SI19:XXXXX
SI20:XXXXX
SI21:XXXXX
SI22:XXXXX
SI23:XXXXX
SI24:XXXXX
SI25:XXXXX
SI26:XXXXX
SI27:XXXXX
SI28:XXXXX
SI29:XXXXX
SI30:XXXXX
SI01:GPS
SI02:XXXXX
SI03:XXXXX
SI04:XXXXX
SI05:XXXXX
SI06:XXXXX
SI07:XXXXX
SI08:XXXXX
SI09:XXXXX
SI10:XXXXX
[MENU
/ ESC]: Back [ENT]: In
p
ut
▲
/
▼
/
◄
/
►
: Select
To switch the channel,
use the cursorpad
(◄ or ►).
Serial Monitor
◄
SI01
►
$GPZDA.104523.4582.23.12.2012.09.00•54
$GPGNS.104523.477.3434.000.N.13510222.E.N.01.1.1.5.0.-2.3.4.1.0•3A
$GPDTM.W84.0.0.1.N.1.0.W.2.0.W72•46
$GPVTG.176.T.180.0.M.1.0.N.1.8.K.A•3C
[MENU
/ ESC]: Back [ENT]: Sto
p
◄
/
►
: Select

1. OPERATION
1-9
[Sensor(LAN) Monitor]
You can monitor the sensor information input to the LAN channels.
To see the information for a sensor(LAN) channel, use the cursorpad to select a sen-
sor(LAN) channel (LN01 to LN64) then press the ENT key to show the sensor (LAN)
monitor screen. The latest received data is displayed on the top of the screen.
Press the ENT key to stop the sensor display. To restart the sensor display, press the
ENT key again.
[Analog Monitor]
You can monitor the sensor information input to the analog channels (AN001 to
AN120).
To shift the page,
use the cursorpad
(◄ or ►).
Sensor(LAN)Channel Select
◄
1 (LN01 - LN30)
►
LN11:XXXXX
LN12:XXXXX
LN13:XXXXX
LN14:XXXXX
LN15:XXXXX
LN16:XXXXX
LN17:XXXXX
LN18:XXXXX
LN19:XXXXX
LN20:XXXXX
LN21:XXXXX
LN22:XXXXX
LN23:XXXXX
LN24:XXXXX
LN25:XXXXX
LN26:XXXXX
LN27:XXXXX
LN28:XXXXX
LN29:XXXXX
LN30:XXXXX
LN01:GPS
LN02:XXXXX
LN03:XXXXX
LN04:XXXXX
LN05:XXXXX
LN06:XXXXX
LN07:XXXXX
LN08:XXXXX
LN09:XXXXX
LN10:XXXXX
[MENU
/ ESC]: Back [ENT]: In
p
ut
▲
/
▼
/
◄
/
►
: Select
To switch the channel,
use the cursorpad
(◄ or ►).
Sensor(LAN)Monitor
◄
LN01
►
$GPZDA.104523.4582.23.12.2012.09.00•54
$GPGNS.104523.477.3434.000.N.13510222.E.N.01.1.1.5.0.-2.3.4.1.0•3A
$GPDTM.W84.0.0.1.N.1.0.W.2.0.W72•46
$GPVTG.176.T.180.0.M.1.0.N.1.8.K.A•3C
[MENU
/ ESC]: Back [ENT]: Sto
p
◄
/
►
: Select
To switch the channel,
use the cursorpad
(◄ or ►).
Analo
g
Monitor ◄1 (AN001 - AN016)►
AN001: - 0. 04V
AN002: 1. 23mA
AN003: 0. 50V
AN004: - 1. 00V
AN005: 0. 23mA
AN006: - 1. 11V
AN007: 0. 45mA
AN008: 2. 50V
AN009: - 2. 12V
AN010: 3. 48V
AN011: 2. 10V
AN012: - 0. 90V
AN013: 6. 17mA
AN014: 4. 39mA
AN015: 2. 25V
AN016: 1. 04V
[MENU
/ ESC]: Back ◄ /
►
: Select

1. OPERATION
1-10
[Digital Monitor]
You can monitor the sensor information input to the digital channels (DC001 to
DC640).
[Image Capture Status]
You can monitor the information of the images recorded in the DCU. The information
for the image captures (the time and date when the image is captured to the VDR, cap-
tured image size, etc.) are updated.
[Audio Monitor]
You can check the status of the microphones and communications equipment (VHF,
etc.).
To switch the channel,
use the cursorpad
(◄ or ►).
Di
g
ital Monitor
◄
1 (DC001 - DC032)
►
DC001: 1
DC002: 1
DC003: 0
DC004: 0
DC005: 1
DC006: 1
DC007: 0
DC008: 1
DC009: 1
DC010: 1
DC011: 0
DC012: 0
DC013: 1
DC014: 1
DC015: 0
DC016: 1
DC017: 1
DC018: 1
DC019: 0
DC020: 0
DC021: 1
DC022: 1
DC023: 0
DC024: 1
DC025: -
DC026: -
DC027: -
DC028: -
DC029: -
DC030: -
DC031: -
DC032: -
[MENU
/ ESC]: Back
◄
/
►
: Select
Ima
g
e Ca
p
ture Status ◄1 / 2 ►
Radar1
Ca
p
tured Time:
01/09/2014
10:30:20
Source:
Xband.1
Location: MFD0
Active: Yes
Resolution:
1280x1024
Radar2
Ca
p
tured Time:
01/09/2014
10:30:20
Source:
Sband.1
Location: MFD0
Active: Yes
Resolution:
1280x1024
ECDIS
Ca
p
tured Time:
01/09/2014
10:30:20
Source:
ECDIS.1
Location: MFD0
Active: Yes
Resolution:
1280x1024
[MENU
/ ESC]: Back ◄ /
►
: Page
To switch the page,
use the cursorpad
(◄ or ►).
Microphone/VHF
volume level
Audio Monitor
Level: Level: Level: Level: Level:
Level: Level: Level: Level: Level:
[MENU
/ ESC]: Back
◄
/
►
: - - -
VHF1
Status:
- - -
VHF2
Status:
- - -
Status:
MIC TestOK
MIC1
Status:
MIC TestNG
MIC2
Status:
Not
Connected
MIC3
MIC8
Status:
MIC TestOK
Status:
Not
Connected
MIC7
Status:
MIC TestNG
MIC6
Status:
MIC TestNG
MIC5
Status:
MIC TestOK
MIC4