Good Way REAM-A-MATIC RAM-5 GT Manual

REAM-A-MATIC
Tube Cleaning Machine
Operating and
Maintenance
Instructions
Read before operating.

RAM 5
2
CONTENTS:
IMPORTANT SAFETY INSTRUCTIONS.................................................................................................3
ELECTRICAL PRECAUTIONS ................................................................................................................4
OPERATIONAL PRECAUTIONS........................................................................................................ 4-5
THE RAM 5 REAM-A-MATIC®........................................................................................................... 5-6
INTRODUCTION ....................................................................................................................................5
SETTING THE SPEED.............................................................................................................................6
ASSEMBLY...............................................................................................................................................6
CONNECTING THE FLEXIBLE SHAFT.................................................................................................6
OPERATION - GENERAL .......................................................................................................................7
OPERATION – MANUAL MODE...........................................................................................................7
OPERATION – SPEED-FEED MODE.....................................................................................................8
INSTALLING THE SHAFT STOP ............................................................................................................9
SPEED-FEED GEAR/ROLLER REPLACEMENT....................................................................................9
FLEXIBLE SHAFTS................................................................................................................................10
SPEED-FEED TROUBLESHOOTING ..................................................................................................10
GENERAL TROUBLESHOOTING........................................................................................................11
STORAGE..............................................................................................................................................12
ROUTINE MAINTENANCE..................................................................................................................12
SPECIFICATIONS .................................................................................................................................12
PARTS LIST...................................................................................................................................... 13-15
PARTS DIAGRAM ........................................................................................................................... 15-19
Thank you for purchasing this Goodway “RAM 5” vari-speed reversing self-feeding
tube cleaner. We appreciate your business and look forward to serving you in the
future. As with all Goodway products, you can be assured that the nest quality
components and workmanship have gone into this machine.
Please take a few minutes to read the following Operating and Maintenance
Instructions. By carefully following the instructions, you will obtain years of
trouble free service from this product. Please pay particular attention to the safety
instructions and exercise caution when using this machine.
GOODWAY®TECHNOLOGIES CORPORATION
HVAC & FACILITY MAINTENANCE SOLUTIONS
For Sales Call: 1-800-333-7467
For Service Call: 1-800-370-2855

RAM 5 3
WARNING
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using this tube cleaning machine.
1. Read all instructions before using unit. Failure to follow all instructions may result in
serious injury.
2. Keep objects, loose clothing, hair and body parts away from openings and
moving parts.
3. Do not overreach or stand on unstable support. Keep good footing and balance at
all times.
4. Stay alert – watch what you are doing!
5. Do not operate the product when fatigued or under the inuence of alcohol
or drugs.
6. Keep operation area clear of all persons.
7. Use personal safety equipment. Always wear eye protection. Dust mask, non-skid
rubber sole safety shoes, hard hat, gloves, and hearing protection
are recommended.
8. Use only GOODWAY recommended accessories and replacement parts.
9. This unit is to be used only by trained operators.

RAM 5
4
ELECTRICAL PRECAUTIONS
• Never expose the unit to rain or the elements. Store unit indoors in a cool, dry area.
• Make certain that the power source conforms to the requirements of
the equipment.
• DANGER: For proper protection this product must be grounded. Always plug
the power cord into a properly grounded receptacle. Improper connection of the
equipment-grounding conductor introduces risk of electrocution. Check with a
qualied electrician or service personnel if you are in doubt as to whether an outlet
is properly grounded. Never remove the grounding prong from the power
cord plug.
• This unit is equipped with a Ground Fault Circuit Interrupter (GFCI) at the plug
end of the cord for electrocution protection. DO NOT REMOVE THIS DEVICE!!
If replacement of the plug or cord becomes necessary, use only identical
replacement parts that include GFCI protection.
• Do not use any type of adaptor with this product.
• WARNING: To reduce the risk of electrocution, keep all connections dry and off
the ground. Do not handle the unit or electrical plug with wet hands.
• When unplugging the power cord, grasp the plug – not the cord.
• Unplug the power cord when servicing the unit or leaving the
machine unattended.
• Do not roll the machine over the power cord, pull the cord, close a door on the
cord or pull the cord around sharp corners. Keep the cord away from hot surfaces.
• Do not use the machine if it has a damaged cord or plug.
OPERATIONAL PRECAUTIONS
• Do not use in an environment or on objects that are above 175°F (79°C).
• Do not use with ammable or explosive uids such as gasoline, fuel oil, kerosene,
etc. Do not use in explosive atmospheres.
• Keep clear of moving shaft. Make sure the shaft will not catch on anything while
in use.
• Check exible shaft for weak or worn condition before each use. Make certain that
all connections are tight and secure.
• If the machine does not operate properly or is damaged contact Goodway
Customer Service.
• Disconnect the plug from the power source and turn off water supply before
disconnecting hoses, ttings, or exible shaft and before making any adjustments
or changing accessories. Such preventive safety measures reduce the risk of
starting the unit accidentally.

RAM 5 5
• Check for misalignment or binding of moving parts, breakage of parts, and any
other condition which may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
• If servicing this unit, use only identical replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of electric shock or injury.
• Be sure to select the proper size exible shaft and tool for the job. Do not force the
tool. Use the correct tool for the application.
• DANGER!! DO NOT OPERATE THE UNIT WITH COVER(S) REMOVED WITH
MOVING PARTS AND ELECTRICAL CONNECTIONS ARE EXPOSED!!!
• Keep objects, loose clothing, hair and body parts away from openings and
moving parts.
THE RAM 5 REAM-A-MATIC®
INTRODUCTION
The RAM-5 Speed-Feed with Variable-Speed Ream-A-Matic® represents the latest
in exible shaft tube cleaning technology. The variable speed function controls both
brush rotational speed and shaft feed rate and allows the operator the ability to match
brush speed and feed rate to the particular cleaning job (enhanced tube, stubborn
deposits, etc). The Speed-Feed attachment mechanically feeds the shaft into the tube,
greatly increasing efciency and reducing operator fatigue. The RAM-5 can also be
used by manually feeding the shaft into the tube, similar to previous Ream-A-Matic®
models. In the manual mode, the full range of cleaning tools can be used to handle
difcult deposits. When the deposits to be cleaned are soft enough to be removed by a
nylon brush, the Speed-Feed attachment makes cleaning quick and easy.
The RAM-5 uses a brush or other cleaning tool on the end of a rotating, nylon-encased
exible steel shaft. As the rotating tool/shaft assembly is fed through the tube, the
brush or tool loosens any deposits (mud, sand, etc) as water owing through the casing
ushes them out. An electronic valve automatically opens the water ow only when
shaft is rotating. The RAM-5 is designed for both enhanced-bore (internally “ried” or
grooved) and smooth-bore tubes with an inside diameter (ID) between 1/4" and 1"
(6.4/25.4mm).
• Enhanced Tubes: The rotational speed of the cleaning tool controls the linear feed
rate of the shaft into the tube. It is important to minimize slip between the brush
and the grooves in the tube. Too much slip (rotational speed exceeds the natural
feed rate of the helix in the tube) won’t allow the brush bristles to reach into the
grooves, leaving them fouled. However, if the brush is not rotating fast enough the
opposite can happen and the operator can end up pushing the brush bristles past
some of the grooves.

RAM 5
6
• Smooth-Bore Tubes: The operator needs only to select a comfortable rotational
speed and feed rate.
Setting the Speed
• The rotational speed of the exible shaft is controlled by the Speed Control on the
unit’s control panel.
• For enhanced tubes start speed at 400 RPM. Increase speed as needed.
• For smooth-bore tubes set the speed at 800 rpm, change if necessary.
ASSEMBLY
1. Place the power unit on bench or
oor with the front louvered
side down.
2. Insert the two large thumbscrews
through slotted holes in the
handlebar and fasten loosely into
the tapped holes in the edges of the
back of the power unit.
3. Push the dolly bar tight against the
bottom of the power unit and tighten
the thumbscrews. The machine may
now be turned upright.
CONNECTING THE FLEXIBLE SHAFT
1. Select the proper size exible shaft (GTC-701, GTC-702, GTC-703, or GTC-704) for
the tube diameter and length to be cleaned.
Note: When the Speed-Feed attachment is used, the exible shaft must be 20' (6.1m)
longer than the longest tube to be cleaned. Speed-Feed attachment is used only with
GTC-702 (Special), GTC-703 or GTC-704 Series Shaft. All other shafts must be fed
manually into a tube
2. Insert the square end of the exible shaft into the square in the drive shaft of the
machine. The shaft might have to be turned slightly for alignment.
3. Push quick connect nut until latches engage.

RAM 5 7
OPERATION - GENERAL
1. Connect water hose to water inlet. Water supply should be clean (use screen
washer) to avoid clogging solenoid valve. Consult Goodway catalog for heavy-
duty water hoses.
2. Open water supply. DO NOT RUN DRY. Solenoid valve in power unit will allow
water to ow only when the machine is running.
3. Plug the ground fault cord into an outlet in
accordance with the electrical requirements
shown on the nameplate. Push the reset
button on the ground fault. The power
indicator light on the machine will light and
the air pump inside the housing will start.
4. Tip the machine over on its back so the
exible shaft is parallel to the oor.
5. Set speed to desired level. Both linear and
rotational are controlled simultaneously
OPERATION – MANUAL MODE
1. Connect either the single or double foot switch to the small air ttings on the right
side (facing power unit) of the power unit. When using the single switch, connect
tubing to the shorter tting.
2. Select proper size cleaning tool and thread onto the end of the exible shaft.
Never use a tool larger than the I.D. of the tube. When using brushes, use the lock
nut provided to keep brush from unthreading in the reverse direction.
Note: Most tubes are rolled at tube sheet. Always measure I.D. beyond roll or consult
manufacturer' manual for tube O.D. and gauge.
3. Position tube length marker on shaft casing so that when the shaft is fully inserted
in the tube, only half the cleaning tool extends outside the opposite end of tube.
4. Uncoil exible shaft completely and feed into tube. DO NOT FORCE SHAFT
DOWN TUBE. Allow machine to do the work. If resistance is felt, back off 2" or 3"
(51 or 76mm) and feed shaft again until it goes easily. If resistance is too great, use
a smaller cleaning tool.
5. For easiest operation, insert shaft into tube and allow to remain for several hours
before use to remove loops from exible shaft.

RAM 5
8
OPERATION – SPEED-FEED MODE
SPEED-FEED ATTACHMENT IS DESIGNED TO BE USED ONLY WITH NYLON
BRUSHES AND GTC-702 (SPECIAL), GTC-703 OR GTC-704 SERIES SHAFTS.
1. Thread the exible shaft guide tube onto the tting of the right side of the power
unit and connect the control hoses to the small air ttings.
2. Squeeze the top of the trigger and note direction of exible shaft rotation. Shaft
should rotate counterclockwise as viewed from the tip. If it does not, reverse
control hoses on air ttings. Squeeze top and bottom of trigger and check for
proper operation. THE SHAFT MUST COME TO A COMPLETE STOP BEFORE
REVERSING DIRECTION.
3. Attach Goodway nylon brush to exible shaft. Securely tighten the small lock nut.
USE ONLY SMALL LOCK NUTS SUPPLIED WITH GOODWAY BRUSHES. Use of a
larger nut will jam the guide rollers. GTC-703Q and GTC-704Q Quick Disconnect
Flexible Shafts and brushes can be used for 9/16"-1" (14.3mm-25.4mm) I.D. tubes.
GTC-702Q Quick Disconnect Flexible Shaft can not be used in Speed-Feed Mode.
4. Remove tube length marker.
5. Install shaft stop (see "INSTALLING THE SHAFT STOP").
6. Make sure the gear/roller set installed is the correct size for the exible shaft being
used, and that the gear portion is toward the gearbox cover. Hold the shaft casing
about two feet from the brush end and insert shaft fully into the entry port on the
left side of the power unit. With shaft fully inserted, squeeze top of trigger to feed
shaft through the guide tube and into the control handle.
7. To adjust the forward shaft stop to the desired tube length, loosen the hex screws
on the locking collar and slide locking collar to the desired position. Retighten hex
screws. THE SPRING AND METAL CONE MUST BE ON THE BRUSH SIDE OF THE
LOCKING COLLAR.
8. Speed-Feed is supplied with a safety strap to protect the operator in the event
that a blockage is encountered in a tube and the control handle is forced back
toward the operator. Fasten the strap across the tube sheet snugly enough to
allow moving the control handle from tube to tube. The safety strap will need to be
moved as the operator moves vertically on the tube sheet. If the tube sheet is too
wide for one strap, connect additional straps as needed. Insert the strap through
the eye on the top of the control handle and connect to tube sheet.
9. Position the control handle over the tube to be cleaned and squeeze the top of
the trigger to enter the tube. The Speed-Feed stops automatically at the preset
distance. Squeeze the bottom of the trigger to reverse out of the tube. When
exiting tube, it is recommended that the control handle be held a few inches away
from the tube end. When the brush is seen, release the trigger.
10. When an unusually heavy build up of deposit is present, the brush may not feed
completely through the tube on the rst pass. I f the Speed-Feed stalls part way
into a tube, stop and reverse the unit to completely exit the tube. Try another
pass through the tube. Repeat this procedure until the entire length of the tube is
cleaned. In extreme cases it may be desirable to switch to manual mode and use a
cleaning tool other than a brush.

RAM 5 9
INSTALLING THE SHAFT STOP
INSTALL THE REAR CONE, COLLAR, SPRING AND THE
FRONT CONE AS FOLLOWS:
1. Insert the shaft through the RAM-5, advancing the shaft through the guide tube
and gun handle, then into the tube to be cleaned for the desired length – let the
brush go halfway out of the tube on the
other end.
2. Go back to the machine and slide the shaft
stop up as close to machine as you can get it
and tighten the collar.
3. Activate the machine and retract the shaft a
few feet then advance it until it stops. Check
to make sure the brush is halfway out of
the tube.
WARNING: Incorrect installation may cause motor failure!!
SHAFT STOP INSTALLATION
SPEED-FEED GEAR/ROLLER REPLACEMENT
DO NOT USE GREASE OR ANY OTHER LUBRICANT ON THE GEARS!! Remove the four
cover screws holding the ribbed cover on the bottom of the power unit.
1. Pry the cover gently and evenly.
2. If present, remove spacers, noting their
position. The spacers must go in the same
position when reassembling the unit. Not all
units require spacers.
3. Remove and install gears as required. Insert
gear/roller so that the gear portion is toward
the cover. Please note that the main drive
gear is keyed to the drive of the power unit.
All other gears are interchangeable.
4. Reverse the above procedure for reassembly.
NOTE: When changing shaft sizes, gears must also be changed. Select gears/rollers,
collar and rear cone from parts list.

RAM 5
10
FLEXIBLE SHAFTS
Please refer to the booklet “Flexible Shafts – Operating and Maintenance Instructions”
for important information about proper use, maintenance, and storage of
exible shafts.
SPEED-FEED TROUBLESHOOTING
SHAFT WILL NOT FEED FORWARD:
• Check to see if shaft casing is caught on drain assembly (2257). Trim casing
if needed.
• Forward stop valve stem needs oil.
NOTE: The forward stop valve stem (part No. 2207, Key #12) must be oiled
approximately every 10,000 tubes. Lack of lubrication can cause the valve stem to stick
holding the valve open. This prevents the unit from feeding the shaft forward. Apply a
light oil (3 in 1, WD-40, etc.) between the forward stop spring and the gearbox/roller
housing inside the base of the power unit. Lubricant can be applied by removing the
cover then placing it on the valve stem.
• Reset ground fault.
• Check control hose connections at power unit.
• Remove control hoses at power unit and check for air ow from the small air
ttings. Cover only one tting at a time.
SHAFT WILL NOT REVERSE:
• Reset ground fault.
• Check control hose connections at power unit.
• Remove control hoses at power unit and check for air ow from the small air
ttings. Cover only one tting at a time.
UNIT RUNS BUT SHAFT DOES NOT MOVE OR MOVES
SLOWLY:
• Check bends in guide tube. Bends should be no less than one foot radius.
• Check to see if guide tubes need cleaning. Clean with 7/8" (22.2mm) nylon brush.
• Check for clogged tube.
• Remove exible shaft from Speed-Feed unit. Wipe any grease or slime off shaft
casing. If the shaft is new, it may be necessary to “rough up” the casing with some
ne sandpaper.
• Check the chain and sprockets for proper tension and alignment.
• Check to see if the bearings (p/n 825-R5) are worn to the point that the gears have
moved slightly apart from each other, thereby reducing their grip. There should be
no side to side movement of the gear in the bearing.
• Follow instructions under “Speed-Feed Gear/Roller Replacement” and clean the
gears/rollers of any lubricant that may be on them.
• Check all air hose connections.

RAM 5 11
GENERAL TROUBLESHOOTING
Problem PROBABLE CAUSE REMEDY
Runs for short period of
time and stops (power
light remains on)
• Leak in air control circuit
• Circuit Breaker Tripped
• Air switch leaking (rare)
• Disconnect power, remove
cover. Disconnect air hoses
from air switches to allow foot
pedal bellows to inate to full
height. Reconnect and tighten
all connections
• Push Circuit Breaker button to
reset
• Replace air switch
Runs in one direction only • Leak in air control circuit
• Faulty wire connection(s)
• Faulty Air switch
• Faulty Control Board
• See Above
• Disconnect power, remove
cover. Check all power
connections
• Check air switches
• Call Goodway
Water leaking from base • Leak in water circuit
plumbing
• Leak at shaft manifold seal
• Disconnect power, remove
cover. Check hoses and ttings
for leaks.
• Check for leak where drive shaft
enters shaft manifold.
Runs for short period of
time and stops (power
light off), GFCI trip/won’t
reset
• Electrical short to ground • If GFCI continually trips call
Goodway - there may be an
unsafe electrical condition!!
Motor jerks or runs
erratically
• Speed Control
• Control board
• Check speed control
potentiometer –check
resistance across outer leads
(~5K ohms). Check resistance
between middle and outer lead
- rotate speed control (0 to 5K
ohms).
• See wiring diagram and check
trimmer pot settings.
Motor runs but shaft does
not turn
• Problem with chain and/or
sprockets
• Broken exible shaft
• Disconnect power, remove
cover. Check chain and
sprockets.
• Replace shaft ttings and/or
core.
No water through exible
shaft
• Problem with water
supply
• Inlet screen clogged
• Main inlet solenoid valve
not working
• Water supply not on,
restrictions in hose or hose too
small, water supply pressure
insufcient.
• Remove hose and clean screen.
• Disconnect power, remove
cover. Check solenoid wiring
and connections.

RAM 5
12
STORAGE
Disconnect water supply line. Disconnect the exible shaft and drain water to prevent
rusting of shaft. Do not store machine where residual water in machine may freeze.
Refer to Flexible Shaft manual for exible shaft storage.
Routine Maintenance
• Lubricate Chain and Sprockets every 100 hours of running time with a good grade
non-detergent SAE 20 to 50 weight petroleum-based oil or NLGI no. 1 or no.
2 grade mixed-base or lithium-soap grease. Apply lubricant to chain sparingly,
and then wipe off excess. DANGER! MAKE SURE POWER IS OFF BEFORE
LUBRICATING CHAIN!
• Check all louvers and water drain holes for obstructions.
• Check for decaying hoses and wire insulation.
• Check for water leaks.
SPECIFICATIONS
Motor 3/4 HP, DC Brush Motor
Nominal Power Requirement 7.5 Amps @ 115 VAC (865 Watts - 115V Model)
3.75 Amps @ 230 VAC (865 Watts - 230V Model)
Maximum Power
Requirement
15 Amps @ 115VAC (1725 Watts - 115V Model)
7.5 Amps @ 230 VAC (1725 Watts - 230V Model)
Rotational Speed 0 – 850 RPM
Water Line Connection 3/4” Standard Garden Hose
Maximum Water Pressure 100 PSI (7 BAR)
WARRANTY INFORMATION
Please check the included warranty card for all warranty information

RAM 5 13
PARTS LIST
KEY# PART# DESCRIPTION QTY.
1 1056 Barbed Fitting 3
3 1417 Light 1
* 1719 Roll Pin, 1/16", Control Gun 2
4 2200 Base 1
5 2201 Cover 1
7 2203 Gear Box 1
8 2203-4 Snap Ring, 40mm 1
9 2204 Gear Box Cover 1
10 2205-702 Driver Roller/Gear (for GTC-702 shaft) 1
2205-703 Driver Roller/Gear (for GTC-703 shaft) 1
2205-704 Driver Roller/Gear (for GTC-704 shaft) 1
11 2206-702 Roller/Gear (for GTC-702 shaft) 4
2206-703 Roller/Gear (for GTC-703 shaft) 4
2206-704 Roller/Gear (for GTC-704 shaft) 4
12 2207 Stop Valve 1
13 2208 Guide Bushing 1
14 2209 Key, 1/8" x 3/16" 1
15 2263 Stop Spring 1
16 2211 Tube, Connector 1
17 2212-1 Support Block 1
18 2214 Air Pump, 115 V 1
214A Air Pump, 230 V 1
29 2227 Fan, (115V Models) 1
2227A Fan, (230V Models) 1
30 2229 Drive Shaft 1
31 M-90VDC-075 Motor, 90 Volt DC, 3/4 HP (115V Models) 1
M-180VDC-075 Motor, 180 Volt DC, 3/4 HP (230V Models) 1
32 2233 Grommet 1
33 2234 Main Wire Harness 1
35 2239 Allen Wrench 1
37 2241 Screen 1
41 2245 Pin, Trigger 1
43 802 Fitting 1
44 803 Screen Washer 1
46 806 Carry Handle 1
47 808 Electrical Connector 1
48 817-3 Switch Cover (115V Models only) 1
49 819 Nipple 1
50 820 Solenoid Valve, (115V Models) 1
820A Solenoid Valve, (230V Models) 1
51 821 Reducer 1
52 822 Elbow 1
53 892Q Manifold 1
54 823N Nuts 2

RAM 5
14
KEY# PART# DESCRIPTION QTY.
55 824 Seal 1
56 825-R5 Bearing 10
57 2286 Sprocket, 48T x 1/2” Bore 1
58 2285 Sprocket, 17T x 5/8” Bore 1
59 2287 Chain, 18" Long w/Master Connecting Link 1
60 833-1 Bearing 1
61 835 Latch 1
62 839 Bumper 7
64 842 GFCI Plug & 30 ft 14 AWG Cord, (115V Models) 1
842A GFCI Plug & 30 ft 14 AWG Cord, (230V Models) 1
* 842AX Romex Clamp 1
66 2267 Air Switch 2
67 871 Receptacle (115 V Models only) 1
* 879 Motor Clip 2
68 847-SF Single Foot Switch 1
72 810 Handlebar 1
73 811 Hanger 1
74 812 Thumbscrews 2
75 812-1 Washer 2
76 813 Wheel 2
77 814-1 Wheel Block Assembly 2
78 814-3 Wheel Bolt 2
79 815 Dolly Bar 1
80 826 Snap Ring 1
83 2249 Air Harness 1
88 2212-4 Bulk Head Fitting 2
* 2256 Receptacle Clip 2
* 840 Bumper Screws 7
91 2264 Coil Return Spring 2
92 609 Screw 2
93 2262 Bracket 1
94 2273 Spacer 2
95 2275 Connector 1
96 R7-12 Controller, For DC Motor (115V & 230 Models) 1
97 SQC-10 Torsion Spring 1
98 SQC-07 Latch 2
99 HWS-1024-163-SC Screw 10-24 1,63 long socket head 3
100 SQC-02 Manifold Outer Ring 1
101 SQC-08 Spacers St. St. 3
102 SQC-01 Manifold Inner Ring 1
PARTS LIST

RAM 5 15
PARTS DIAGRAM
SQC-ASSM-892-R5

RAM 5
16
RAM-5 GT
2219-702
2219-703
2219-704

RAM 5 17
PARTS LIST
KEY# PART# DESCRIPTION QTY.
2 1321-1 Outer Sleeve 15' (4.6m)
20 2216 Hose Fitting, Female 1
21 2217-15 Guide Tube 15' (4.6m)
22 2218 Control Handle 1
23 2219-2 Coil Spring 1
24 2219-703-1 Cone 1
25 2219-703-2 Collar (for GTC-703
shaft)
1
2219-704-2 Collar (for GTC-704
shaft)
1
26 2219-703-4 Rear Cone (for GTC-
703 shaft)
1
2219-704-4 Rear Cone (for GTC-
704 shaft)
1
27 2224 Trigger 1
28 2225 Trigger Pads 2
34 2238 Bumper, Tube 1
63 841R Twin Hose 18' (5.5m) 18' (5.5m)
69 DDC-4 Pin 1
70 DDC-5 Ring 1
81 2248 Tube, Control Gun 1
82 2244 Safety Strap 1
84 2212-5 Fitting 2
85 HWC-113 Clamp 1
86 2253 Elbow 4
87 2254 Orice 2
89 HWS1162SH Screw 6
90 2257 Drain Assembly 1

RAM 5
18
WIRING DIAGRAMS
RAM-5-DC, 115 VOLT WIRING DIAGRAM

RAM 5 19
RAM-5A-DC, 230 VOLT WIRING DIAGRAM

Provides innovative maintenance solutions for a wide variety
of industries including commercial HVAC, food and beverage
processing, power generation and manufacturing.
HVAC & FACILITY MAINTENANCE SOLUTIONS
For Sales Call: 1-800-333-7467
For Service Call: 1-800-370-2855
GOODWAY®TECHNOLOGIES CORPORATION
420 West Avenue, Stamford, CT 06902 USA
Tel: [phone] · Toll-Free Tel: [phone]
Fax: [phone] · Toll-Free Fax: [phone]
Email: [e-mail]
Visit: www.goodway.com
P/N RAM-5DC
©Copyright 2019 Goodway Technologies Corp., Stamford, CT USA
Effective date March 13, 2019
Goodway is a Trademark of Crossford International.
Goodway reserves the right to improve products; contact the factory for the latest conguration and uses.