Great Little Trading Alba L4472 User manual

1
Alba Corner Base Unit & Top Shelf
L4472
easy - medium - hard
Assembly Difculty
two-person job
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools.Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the tools
you need at the beginning of the instructions.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail
through the whole process. But if it all feels a bit too much
like hard work, then we do have an assembly company we
can recommend: the Flatpack Construction Company offers a
nationwide service and can be contacted on 0843 289 4951 or
www.atpackconstruction.co.uk.
13/06/2019
V1

2
Safety Warnings:
Please read these instructions carefully before assembly.
• During assembly children should be kept away from the product due
to possible risk of injury.
• Assemble and use on a at and level surface.
• This product is heavy, we recommend that you build it where you are
planning to use it.
• This unit can only be used in conjunction with other Alba Corner
units.All stacked Alba furniture must start with a GLTC Alba base unit.
• It is recommended that the Alba range is only stacked 3 units high i.e.
1x corner base + top shelf & 2x corner shelf units.
• DO NOT use power tools in the assembly of this product as there is a
risk of over tightening and consequently splitting of the wood.
• Do not over tighten hardware. Cam dowels should be inserted to
the collar. Back panel screws should be screwed until they naturally
tighten/stop. This is difcult to feel if power tools are being used.
• WARNING! FURNITURE TIPPING RISK. Serious or fatal crushing
injuries can occur from furniture tipping over. Ensure you secure this
furniture product to the wall before you use it, using the kit provided.
If you have not received an anti-tip kit with your product please
contact Customer Services.
• To avoid possible injury from tipping - DO NOT allow children to step
or climb on the product.
• Check all xtures and ttings regularly and tighten as necessary.
• Remove all packaging before allowing your child to use the product.
• Please retain for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
• Regularly check all fastenings, xtures and ttings to ensure that they
properly tightened.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
A B
C D
E F
G H
I
1x Top Shelf - LH Base Panel
Component Check List Component Check List
J
K L
1x Top Shelf - RH Base Panel
1x Top Shelf - LH Side Panel 1x Top Shelf - RH Side Panel
1x Top Shelf - RH Back Upstand 1x Top Shelf - RH Back Upstand
1x Base Unit - LH Side Panel 1x Base Unit - RH Side Panel
1x Base Unit - LH Top Panel 1x Base Unit - RH Top Panel
1x Base Unit - LH Base Panel 1x Base Unit - RH Base Panel
1x Base Unit - Back Support Panel 1x Base Unit - Back Support Panel
1x Base Unit - Back Panel 1x Base Unit - Back Panel
M N
O P

4
#1 #2
#3 #4
#5 #6
You will need
(not supplied)
Philips Head Screwdriver
Component Check List
23x Cam Dowels
35mmL
30x Wooden Dowels
25mmL
35x Cam Locks
15mmL dia
24x Domed Head Screws
14mmL
6x Double Ended Cam Dowels 1x Anti-tip kit

5
DC
#1
#2
Hardware for Step 1: Hardware for Step 2:
2x #2 Wooden Dowels 7x #1 Cam Dowels
4x #3 Cam Locks
2x #5 Double Ended
Cam Dowels
Using Cam Locks:
When inserting into the panel, ensure that each cam lock’s
arrow is pointing towards the drill hole on the side edge of
the panel & the dowel that it will be receiving.
When the panels are in the connected position, using a
screwdriver, turn the cam lock in a clockwise direction to
lock and secure.
STEP 1:
Take top shelf panels A & B and position with large drill holes facing up and the
angled edges next to each other as shown.
Insert 2x wooden dowels (#2) into the inner holes on the angled edge of panel A.
Insert 2x double ended cam dowels into the outer holes on the edge of the same
panel.
Insert 2x cam locks into the large drill holes on the same panel and turn clockwise to
lock.
Pull the ends of cam dowels out a little.
Now push the two panels together and insert 2x cam locks (#3) into the large drill
holes on panel B and turn clockwise to lock.
STEP 2:
Using a Phillips screwdriver, prepare the top shelf side panels by inserting 3x cam
dowels (#1) into the smaller holes of BOTH panels D & C.
Then insert 1x cam dowel (#1) into the end of panel E.
A B
#3 #3
#3 #3
#1 #1
#1 #1
#1 #1
#5
#5
#2
#2
DC
#1
E
#1

6
STEP 3:
Create the upstand. Take panel F and
connect to panel E. Insert 1x cam lock into
the large hole by the connection and turn
clockwise to lock.
Ensure the large drill holes on both panels
are facing outwards as shown.
STEP 4:
Insert 4x cam dowels (#1) into the smaller,
outer drill holes on both panels A & B.
B A
E F
#1
Hardware for Step 4:
Hardware for Step 3:
4x #1 Cam Dowels
1x #3 cam lock
STEP 5:
Insert 4x wooden dowels into the remaining holes on
A/B panels.
Push the upstand panels E/F onto the A/B panels and
insert 4x cam locks into the large drill holes on E & F.
Turn clockwise to lock.
B
E F
A
#3
#2
Hardware for Step 5:
4x #2 Wooden Dowels
4x #3 Cam Locks
#3
#1
#1 #1
#1
#2
#2
#2
#2
#3
#3
#3
#3

7
#2
#3
C
A B
D
STEP 6:
Insert 2x wooden dowels (#2) into the innermost
holes on the edges of panels A & B.These will insert
into the larger holes on panels C & D.
Attach the side panels and secure using 3x cam locks
(#3) on BOTH sides.
NOTE:The shaped side of the side panels to be facing
up as shown.
STEP 7:
The top shelf is now ready for use.
Hardware for Step 5:
4x #2 Wooden Dowels
6x #3 Cam Locks
#3
#3
#3 #3
#3
#3
#2
#2
#2 #2

8
STEP 8:
Repeat Step 1 to join the corner panels
together. Join panels I & J (base unit top
panel), then K & L (base unit base panel).
Ensure all cam locks are tightened before
moving to the next step.
STEP 9:
Carefully turn joined panels K & L over,
to show the small set of drill holes in the
corner.
Insert 2x cam dowels (#1) into the smaller,
middle drill holes in the corners of BOTH
sets of joined panels.
Hardware for Step 8:
4x #2 Wooden Dowels
8x #3 Cam Locks
4x #5 Double Ended
Cam Locks
#3 #2 #1
I I
K K
J J
L L
Hardware for Step 9:
4x #1 Cam Dowels
#3
#3
#3
#3
#3
#3
#3
#3 #1 #1
#2
#2
#5
#2
#2
#5
#5
#5
#1 #1

9
STEP 10:
Insert 4x cam dowels (#1) into BOTH of the
base unit side panels G & H.
STEP 11:
Take the K/L base panel and
insert 4x wooden dowels into the
remaining holes in the corner.
Position back support panel N rst,
it needs to be at on the oor. The
large drill holes on the panel to be
facing the oor and the small pilot
holes on the edge MUST be facing
outwards by the corner. Push onto
the the dowels of K/L.
Now take back support panel M and position with the drill holes facing outwards.
Push onto the dowels of K/L and insert 1x cam lock into the hole that can be seen
and turn clockwise to lock.
Take the I/J top panel and insert 4x wooden dowels into the remaining holes in the
corner.
Now push this onto the back support panels N & M.
Insert 1x cam lock in the large hole on panel M and turn clockwise to lock.
NOTE: The cam locks on panel N will be secured at a later stage.
Hardware for Step 10:
8x #1 Cam Dowels
#1
#2
#3
G
K
L
I
J
H
Hardware for Step 11:
2x #3 Cam Locks
BASE
TOP
It is important that these
small pilot holes are visible
and in this position on panel
N, as they are needed in a
later step.
NM
#1
#1
#1
#1
#1
#1 #1
#1
#3
#3
#2
#2
x4
x4
8x #2 Wooden Dowels

10
STEP 12:
Take side panel H and insert 4x wooden dowels in
the remaining drill holes.
Line up the grooved edge on panel H with the
grooved edges of the corner panels and push on to
the ends of panels L & J.
Insert 4x cam locks into the drill holes on panels L
& J and turn clockwise to lock.
STEP 13:
Keeping the unit in the same position, repeat step
12 with panel G.
This time, ensure the grooved edge is facing the
the oor.
Tighten all cam locks fully.
Now the unit is stable, please carefully lower it
onto its base.
Hardware for Step 12: Hardware for Step 13:
4x #2 Wooden Dowels 4x #2 Wooden Dowels
4x #3 Cam Locks 4x #3 Cam Locks
K
L
G
H
H
M
#2
#2
#3
#3
BASE
TOP
#2
#2
#2
#2
#3
#3
#3
#3
#3
#3
#3
#2
#2
#2
#2
#3