Great Little Trading Loxley L5013 User manual

1
Loxley Storage Cupboard
L5013
Assembly Difculty
two-person job
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools.Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the tools
you need at the beginning of the instructions.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail
through the whole process. But if it all feels a bit too much
like hard work, then we do have an assembly company we
can recommend: the Flatpack Construction Company offers a
nationwide service and can be contacted on 0843 289 4951 or
www.atpackconstruction.co.uk.
20/07/2020
V1
easy - medium - hard

2
Safety Warnings:
• Adult assembly required.
• In an unassembled state product contains small parts which may pose
a choking hazard, not suitable for children under 3 years.
• Assembly to be carried out by a competent adult only. During
assembly children should be kept away from the product due to
possible risk of injury. Do not use this item if any components are
missing or damaged.
• DO NOT over load. Max weight 50Kg in total.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• Assemble and use on a at and level surface.
• This product is heavy. We recommend that you build it where you are
planning to use it.
• Serious or fatal crushing injures can occur from furniture tipping over.
In order to prevent overturning, ensure you secure this furniture
product to the wall before you use it, using the anti-tip kit device
provided. If you have not yet received an anti-tip kit with your product
please contact customer services. You will need to source suitable
xings for your wall . If in doubt, please consult a qualied trades
person.
• Do not let children climb or hang on drawers, doors or shelves.
• Place the heaviest items in the lower drawers or shelves.
• Regularly check all xtures and ttings to ensure that they properly
tightened and tighten as necessary.
• PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
• Regularly check all fastenings, xtures and ttings to ensure that they
properly tightened.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
A B
C D
EF
1x Side Panel
Component Check List Component Check List
1x Side Panel
1x Top Shelf 1x Mid Shelf
1x Upper Back Panel 1x Lower Back Panel
1x Base Panel 4x Wooden Feet
G H
I J
1x Door Panel 1x Door Panel
#1 #2
#3 #4
#5 #6
You will need
(not supplied)
Philips Head Screwdriver
#7 #8
#9 #10
12x Cam Locks
20x Wooden Dowels
12x Cam Dowels
2x Wooden Handles
2x Handle Bolts
(18mm)
4x Bolts
(25mm)
8x Door Screws
(12mm)
1x Magnet Catch
2x Screw
(15mm)
18x Back panel Screws
(20mm)
1x Anti- tip Kit2x Pairs of Hinges
#11

4
Hardware for Step 1:
STEP 1:
Take Mid Shelf panel D and attach the magnet catch (#8) using 2x 15mm
screws (#9).
Please note that the position of the magnet catch can be adjusted.
Once the unit is fully built and the doors are on you may need to move the
magnet catch forward or back to make sure the doors are closing properly.
To do this, release the screws, move the catch, then re-tighten.
1x #8 Magnet Catch
2x #9 Screws (15mm)
D
A
#8
#2
#2
#2
#2
#9
STEP 2:
Using a phillips screwdriver, insert 4x Cam dowels (#2) into the outer drill
holes of BOTH panel A and B.
Hardware for Step 2:
8x #2 Cam Dowels
B
#2
#2
#2
#2

5
STEP 3:
You will be building this unit with the back on the oor.
The back edges of the panels will have a groove or pilot
holes on it.
Insert 6x wooden dowels (#3) into the remaining small
holes on panel A as shown. Position panel A with the
grooved edge on the oor.
Take Top Shelf Panel C and orientate with the upstand
and grooved edge on the oor and join with panel A on
the top set of dowels. When in position and connected,
insert 2x cam locks (#1) into the large holes by the join
and turn clockwise to secure.
STEP 4:
Insert 6x wooden dowels (#3) into the remaining small
holes on panel B as shown.
Position panel B with the grooved edge on the oor and
join it to the part assembled unit.
Insert 2x Cam Locks (#1) into EACH shelf by the join and
turn clockwise to secure.
C
D
A
A
C
D
#1
#3
Hardware for Step 3: Hardware for Step 4:
4x #1 Cam Locks 4x #1 Cam Locks
6x #3 Wooden Dowels 6x #3 Wooden Dowels
Using Cam Locks:
When inserting into the panel, ensure that each cam lock’s arrow is
pointing towards the drill hole on the side edge of the panel & the
dowel that it will be receiving.
When the panels are in the connected position, using a screwdriver,
turn the cam lock in a clockwise direction to lock and secure.
#1
#1
#3
#3
#3
TOP
TOP
BASE
BASE
B
#1
#1
#1
#1
#3
#3
#3
#3
#3
#3
Now take mid shelf panel D and orientate so that the magnet catch is at the top
and join to the middle of panel A. When in position, insert 2x cam locks (#1) into
the large holes by the join and turn clockwise to secure.
#3
#3 #1

6
STEP 5:
Insert 4x cam dowels (#2) into the outer holes of
base panel G as shown.
Then insert 4x wooden dowels (#3) into the inner
holes.
With the grooved edge on the oor, join the base
panel G with the rest of the unit.
When in position, insert 4x cam locks into the large
drill holes on both side panels (A & B) and turn
clockwise to secure.
STEP 6:
Attach the feet to the base using 1x wooden dowels (#3) and 1x 25mm bolt
(#7) for EACH foot.
G
#2
#2
#2
#2
G
A
B
#1
#1
#1
#1
#3
#3
#3
#3
TOP
#3
H
H
H
H
#7
#7
#7
#3
#3
#3
Hardware for Step 6:
4x #7 Bolts (25mm)
4x #3 Wooden Dowels
Hardware for Step 5:
4x #1Cam Locks
4x #2 Cam Dowels
4x #3 Wooden Dowels
#3
#7

7
STEP 8:
With the help of a second person, carefully stand
the unit on its feet.
Insert the hinge sets into each side of the unit.
STEP 7:
With the help of a second person, carefully turn the
unit over.
Position lower back panel F in the cupboard section
(nearest the feet.) Position the upper back panel E
on the top where the shelf is.
E
F
#10
Hardware for Step 8:
2x #11 Pairs of Hinges
#11
#11
Hardware for Step 7:
18x #10 Back panel Screws
(20mm)
Ensure the holes on the back panels and the pilot holes in the unit are clearly
aligned.
Carefully insert 18x back panel screws (#10) into the holes and tighten with a
Phillips screwdriver. It is important these screws are inserted straight or you risk
damaging the unit.
There are 2 holes highlighted below that are left to apply the anti-tip kit that is
provided.
The protruding rod on each hinge needs to be pushed in the drill holes on the
base panel (H) and underside of the mid shelf (D).
Pivot the hinges out in order to receive the door panels.
Protuding rod goes into drill
hole on base panel
Protuding rod goes into drill
hole on underside of mid shelf
D
H

8
STEP 10:
Attach the 2x handles (#4) to the doors using 2x handle
bolts (#5).
If you need to adjust the magnet catch, please do so now.
Your unit is now ready to use.
x2
x2
x2
x2
Hardware for Step 9:
8x #6 Door Screws
l
J
STEP 9:
Two people are needed for this step.
Take door panel J and slide into the hinges on the
RH side of the unit (when facing), aligning the drill
holes on the door with those on the hinge.
Note the magnet plate is pre-attached and this
should end up on the inside of the cupboard.
Insert 4x door screws (#6) into the hinges, starting
at the top.
Ensure the screws are fully inserted and lay at
against the hinge.
Repeat with door I.
#4
#4
#5
#5
Hardware for Step 10:
2x #4 Wooden Handles
2x #5 Handle Bolts (18mm)
Copyright© 2020 G.L.T.C. Ltd. All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
NOTE: You need to x the hardware
on one door before moving to the next
one.
#6
#6
#6 x2 #6
#6