Great Little Trading Whittington L4981 User manual

1
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools.Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the tools
you need at the beginning of the instructions.
• It’s a good idea to build the unit in the room where you are going to be
using it, to avoid the need to move it after it’s been assembled.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts and hardware.
easy - medium - hard two-person job
Assembly Difculty
Thank you for shopping with GLTC, we hope you enjoy having
this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail through
the whole process. But if it all feels a bit too much like hard work, then
we do have an assembly company we can recommend: the Flatpack
Construction Company offers a nationwide service and can be
contacted on 0843 289 4951 or www.atpackconstruction.co.uk.
Whittington Desk & Hutch
www.gltc.co.uk
29/04/2020
V4

2
Safety Warnings:
• Adult assembly required.
• Unassembled product contains small parts which may present a
choking hazard.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• Assemble and use on a at and level surface.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• Check all xtures and ttings regularly and tighten as necessary.
• Please retain these instructions for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• The painted/lacquered surface is resistant to staining if cleaned
immediately, however please protect the surface from contact with
ball point pen and indelible style felt markers as the ink is by nature
permanent.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
Component Check List
A I
C K
E
GH
B J
D L
F
1x Desk Top 1x Hutch: Side Panel
1x Drawer Front 1x Hutch: Small Shelf
2x Drawer Sides
1x Hutch: Back Panel
4x Desk Legs 1x Hutch: Vertical Divider
1x Drawer Back 1x Hutch: Top Shelf
1x Drawer Base
1x Hutch: Side Panel

4
Component Check List Component Check List
#1 #9 #2 #10
#3 #11
#5
#4
13x Cam Lock
2x L-Shaped Runner
8x Bolt (57mm)
13x Cam Dowel
2x Flat Runner
20x Wooden Dowel 1x Drawer Handle
7x Wood Screw
(30mm)
8x Flat Washer 8x Split Washer
#6
#7 #8
12x Wood Screw
(14mm)
(not supplied)
Your will need a Phillips
Screwdriver

5
STEP 1:
Position the desk top on a protective surface like a rug or carpet as shown.
Attach the 2x at runners (#9) to the inside of the desk. Ensure the runners
are positioned with the wheels at the front opening of the desk and with the
wheel on the upper edge of the runner as shown.
Use the holes shown to attach the runner to ensure the positioning is correct
and use 3x screws (#6) to attach each runner.
Ensure the screws are fully inserted to ensure the drawer runs smoothly.
STEP 2:
Prepare the hardware to attach the legs by taking 1x bolt (#4), thread on 1x
split washer (#8) followed by 1x at washer (#7). Prepare all remaining bolts.
Take one leg (B) and attach to the desk top using 2x of the pre-prepared bolts/
washer sets.
Please note: When screwing in the pairs of bolts, for smoother insertion do
not screw one individual bolt all the way in, but instead alternate securing each
of the bolts until they are completely secure and as tight as they can possibly
go.
Repeat with 3 remaining legs (B).
Hardware for Step 1:
Hardware for Step 2:
6x #6 Wood screws (14mm)
8x #4 Bolts (57mm)
8x #8 Split Washers
8x #7 Flat Washers
A
A
B
B
B
B
#8 #7
#6
#6
#6
#9
#4

6
STEP 3:
Take both of the drawer side panels (E) and position
with drawer back panel (D) so that the grooves on
the panels are all facing inwards and aligning. The
small drill holes along the edges of the panels E
should be visible and facing up.
Fix the side panels to the back panel using 2x #5
screws on BOTH sides.
Hardware for Step 3:
4x #5 Wood Screws
(30mm)
F
#5
STEP 4:
Slide drawer base panel F into the grooves.
E
E
D
E
E
D

7
STEP 5:
Take the drawer front panel C and insert 2x cam
dowels (#1) into the 2 smaller holes on the ends
of the panel. Insert 2x wooden dowels (#3) into
the larger holes.
Attach the drawer handle (#11) using 1x screw
(#5).
STEP 6:
Attach the drawer front to the drawer box.
Insert 2x #2 Cam locks into the large holes on
the side panels and turn clockwise to secure in
place.
Hardware for Step 6:
2x #2 Cam Locks
Hardware for Step 5:
2x #1 Cam Dowels
2x #3 Wooden Dowels
1x #11 Handle
1x #5 Wood Screw
(30mm)
#5
#1
#2
#3
#11
C
C
E
E
Using Cam Locks:
When inserting into the panel, ensure that
each cam lock’s arrow is pointing towards the
drill hole on the side edge of the panel & the
dowel that it will be receiving.
When the panels are in the connected
position, using a screwdriver, turn the cam lock
in a clockwise direction to lock and secure.

8
STEP 7:
Turn the drawer over so the small holes on
the edges of the side panels are visible.
Position 2x L-Shaped drawer runners (#10)
on each side ensuring the wheel is at the
back of the drawer.
Secure both runners to the drawer using 6x
screws (#6).
STEP 8:
Carefully stand the desk up on its legs and insert the
drawer.
Hardware for Step 7:
2x #10 L-Shaped Runners
6x #6 Wood Screws (14mm)
#6
#6
#10
#6

9
STEP 9:
Prepare both hutch side panels (H & I) and
insert the cam dowel and wooden dowel
hardware into the pre-drilled holes as shown.
Cam dowels to go in the smaller holes,
wooden dowels in the larger holes.
STEP 10:
Position side panel H on the oor and push
hutch back panel (G) into position onto the
hardware as shown.
Keep the back panel supported and insert 2x
cam locks (#2) into the drill holes on the back
of panel G, turning clockwise to secure.
Hardware for Step 9:
Hardware for Step 10:
10x #3 Wooden Dowels
7x #1 Cam Dowels
H
I
#1
#2
#3
2x #2 Cam Locks
H
G

10
STEP 11:
Take the upper shelf panel (L) and insert 2x
wooden dowels (#3) and 1x cam dowel (#1) into
the holes shown.
Then x panel L onto the hutch back/side panels
as shown.
Insert 1x cam lock (#2) into the large hole by the
side panel and turn clockwise to secure.
STEP 12:
Take vertical divider panel (J) and insert 2x
wooden dowels (#3) and 1x cam dowel (#1)
into the holes shown.
Then x panel J onto panel L as shown. Insert
1x cam lock (#2) into the top of panel J and
turn clockwise to secure.
Hardware for Step 11: Hardware for Step 12:
L
L
L
H
H
J
J
G
G
#1
#1
#3
#3
#2
#2
1x #1 Cam Dowels 1x #1 Cam Dowels
2x #3 Wooden Dowels 2x #3 Wooden Dowels
1x #2 Cam Lock 1x #2 Cam Lock