Grizzly T33255 User manual

For questions or help with this product contact Tech Support at [phone] or [e-mail]
MODEL T33255
61" 9-DRAWER
TOOL CHEST
INSTRUCTIONS
Introduction
The Model T33255 9-Drawer Tool Chest requires
some assembly. Follow the instructions below for
assembly, operation, and maintenance.
Figure 1. Model T33255.
• To reduce risk of crushing injuries from
tool chest tipping over on you:
— Do not stand on tool chest or in drawers.
— Keep wheels locked and turned facing
front of tool chest.
— Push tool chest only. Do not pull it.
— Only open one drawer at a time.
— Only move or transport tool chest with
all drawers closed and locked.
• Do not exceed weight capacities:
— Max individual drawer weight limit
is 100 lbs.
— Max tool chest weight limit (including
contents) is 1150 lbs.
• To prevent accidental rolling, always lock
brakes after moving tool chest.
• Do not allow children to have unsupervised
access to tool chest.
Assembly
1. Attach handle to each side of tool chest with
(4) 1⁄4"-20 x 1⁄2" hex bolts (see Figure 2). Do
not over-tighten!
Inventory
Description Qty
• Tool Chest with Drawers ............................ 1
• Fixed Casters ............................................. 2
• Swivel Casters with Brake .......................... 2
• Handles ...................................................... 2
• Keys ............................................................ 2
• Hex Bolts 1⁄4"-20 x 1⁄2" ................................. 8
• Hex Bolts 3⁄8"-16 x 1"................................. 16
• Power Cord ................................................. 1
Note: Some inventory items may be stored in
drawers.
Needed for Setup
Description Qty
• Additional Person ....................................... 1
• Open-End Wrenches 7⁄16", 9⁄16" ..............1 Ea.
Figure 2. Handle installed.
x 4
Handle
(1 of 2)
COPYRIGHT © MARCH, 2022 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 04/22) #SS22275 PRINTED IN CHINA V1.03.22
***Keep for Future Reference***

-2- Model T33255 (Mfd. Since 4/22)
Figure 3. Example of caster installation.
2. Remove casters and hardware from bottom
drawer.
3. With help from another person, lay back of
tool chest flat on floor.
Note: We recommend sweeping the floor
clean and laying down a piece of cardboard
or a blanket to prevent scratching the finish
during this step.
4. Attach each caster using (4) 3⁄8"-16 x 1" hex
bolts (see Figure 3).
5. Return tool chest to upright position.
Locking Caster
To lock caster, press down on caster lock (see
Figure 4). Secure each corner caster to ensure
tool chest will not shift position.
Figure 4. Location of caster lock.
Caster Lock Unlock
Lock
Removing & Installing Drawers
To remove and install drawers:
1. Fully extend drawer and remove contents.
2. Push left locking tab down and hold, then pull
right locking tab up and hold (see Figure 5).
Note: Larger lower drawers feature two
guides per side.
The drawers can be removed and re-installed if
necessary.
3. Pull drawer out to remove.
4. To re-install, insert drawer runners into slides
(see Figure 5) and push drawer completely
in. Locking tabs will automatically snap into
place to secure drawer in slides.
Locking Drawers
Use the included keys to secure the drawers. Only
completely closed drawers will lock.
Maintenance
• Use soft, clean cloth and soapy water (use
regular dish soap) to remove grease, dirt, or
oil. Do not use solvents or flammable clean-
ing liquids.
• Lubricate drawer slides as needed with dry
lubricant, such as Grizzly's Model G4682
Sprayway Dry Coating Lube.
• Use graphite to lubricate lock annually.
x 16
Caster
(1 of 4)
Tool chests can tip and cause crushing
injury when wheels are not set up properly.
When stationary, wheels should always
be locked and turned facing the front of
the tool chest to avoid injury and prevent
tipping accidents.
Figure 5. Location of drawer locking tabs.
Right Locking Tab
Left Locking Tabs
Drawer Runner

Model T33255 (Mfd. Since 4/22) -3-
Power Strip
The T33255 features a pre-installed power strip
with (4) 5-15 outlets and (2) USB ports, conveniently
located for easy access. The included power strip
has the following ratings:
Power
Cord with
Plug
Figure 6. Example of power strip and plug
location.
Grounding & Plug Requirements
Figure 7. Typical 5-15 plug and receptacle.
Grounding Pin
Neutral Hot
5-15 PLUG
GROUNDED
5-15 RECEPTACLE
Electrocution, fire, shock,
or equipment damage
may occur if power strip
is not properly grounded
and connected to power
supply.
Max. Amperage Load..................................12A
Max. Voltage .............................................. 125V
Cycle ..........................................................60 Hz
Max. Wattage ..........................................1500W
USB Output............................ 5VDC, Max. 2.1A
• Do not connect to plug receptacle via
extension cords or in series with other
power strips.
• Keep electrical connections clear of flam-
mable materials.
• Keep electrical connections dry. Do not
use in damp or wet conditions.
• Do not connect devices to power strip
that draw more than listed power strip
rating. Equipment must be used in accor-
dance with any instructions or labeling.
• Power strips are designed for use with
low-powered loads, such as battery char-
gers. Not designed for use with high-
powered loads, such as space heaters or
microwaves.
• Do not run cord under floor coverings or
where it may be tripped over.
• Not meant for outdoor use.
• Prevent unauthorized use by children or
untrained users.
110V Circuit Requirements
Nominal Voltage .................... 110V, 115V, 120V
Cycle ..........................................................60 Hz
Phase ........................................... Single-Phase
Power Supply Circuit ......................... 15 Amps
Plug the provided power cord into the power strip
socket (see Figure 6).
This tool chest is prewired to connect to a power
supply circuit that has a verified ground and
meets the following requirements:
A power supply circuit includes all electrical equip-
ment between the breaker box or fuse panel in the
building and the power strip. The power supply
circuit used for this power strip must be sized to
safely handle the full-load current drawn from the
power strip for an extended period of time. (If this
power strip is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
This power strip MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
This power strip is equipped with a power cord
that has an equipment-grounding wire and a
grounding plug. Only insert plug into a matching
receptacle (outlet) that is properly installed and
grounded in accordance with all local codes and
ordinances. DO NOT modify the provided plug!
Socket
Power Strip

-4- Model T33255 (Mfd. Since 04/22)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
1
2
4
5
6
7
9
11
12
13
14
15
17
8
310
18
19
20
16
22
21
•110V
•Single-Phase
•12 Amps Max.
FIREHAZARD!
Do not connect
equipmentwith
higheramperage
ratingthan this
receptical.
23
24
T33255 Parts Breakdown & List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1PT33255001 DRAWER SLIDE SET 13 PT33255013 DRAWER, MI DDLE
2PT33255002 HEX BOLT 3/8-16 X 1 14 PT33255014 DRAWER, TOP
3PT33255003 HEX BOLT 1/4-20 X 1/2 15 PT33255015 GRIZZLY NAMEPLATE
4PT33255004 LOCK SET WITH 2 KEYS 16 PT33255016 POWER CORD 18G 3W 72" 5-15P/C14
5PT33255005 CASTER, 6" FIXED 17 PT33255017 POWER CORD BRACKET
6PT33255006 CASTER, 6" SWIVEL WITH BRAKE 18 PT33255018 QR CODE LABEL
7PT33255007 DRAWER LI NER, SMALL 19 PT33255019 WARNING LABEL
8PT33255008 DRAWER LI NER, LARGE 20 PT33255020 GRIZZLY.COM LABEL
9PT33255009 CABINET BODY 21 PT33255021 POWER STRIP 18G 3W 6"
10 PT33255010 HANDLE 22 PT33255022 MOUNTI NG PLATE
11 PT33255011 WOOD TOP 23 PT33255023 POWER STRIP LABEL
12
PT33255012 DRAWER, LOWER
24
PT33255024 PHLP HD SCR 8-32 X 1/2
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call [phone] or visit our online parts store at www.grizzly.com to check for availability.
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact [phone] or www.grizzly.com.