HE-VA Combi-Disc Series Guide

8000501-01 200620

DK Combi-Disc 4,5 –5,5 m 15-04-2020
3 Tilbage til indholdsfortegnelse
Contents
Delivery check..................................................................................................................................................... 4
Setting-up of the machine .............................................................................................................................. 4
Safety Instructions for Combi-Disc..................................................................................................................... 5
Safety and Instructions on Hydraulics................................................................................................................. 6
Complaints........................................................................................................................................................... 6
Labels on the machine......................................................................................................................................... 7
Safety –and other markings on the machine................................................................................................ 7
Technical Specifications / Data........................................................................................................................... 8
Transport ............................................................................................................................................................. 8
Attachment...................................................................................................................................................... 9
Uncoupling ..................................................................................................................................................... 9
Settings and adjustment..................................................................................................................................... 10
Drawbar ........................................................................................................................................................ 10
Disc................................................................................................................................................................ 10
He-va SAT system:....................................................................................................................................... 11
Stone protection............................................................................................................................................ 14
Quick-Push shearpin.................................................................................................................................... 14
Hydraulic automatic release system............................................................................................................. 15
Replacement of wearing point...................................................................................................................... 16
Maintenance and service ................................................................................................................................... 17
Lubrication ................................................................................................................................................... 17
Spare parts list ................................................................................................................................................... 21
Drawbar and cylinder................................................................................................................................... 21
Pivoting Crossbar no. 630757077 Cat. 3 / Cat. 4 and Ball Hitch (Optional)............................................. 23
Pivoting crossbar no. 630757034 Cat. 3 (Optional).................................................................................... 24
Tine Quick Push with 200 mm wearing point, long and short as well as left/right model........................ 25
Tine Quick Push with 120 mm Easy Draft wearing point, long and short as well as left/right model..... 27
Overview Quick Push tineholders................................................................................................................ 29
Notes.................................................................................................................................................................. 30
Tine hydraulic with 200 mm wearing point, long model, (short not shown).............................................. 31
Tine hydraulic with Easy Draft 120 mm wearing point, long model.......................................................... 33
Tiller middle frame and wings..................................................................................................................... 35
Support wheel ............................................................................................................................................... 37
Spindle for support wheel............................................................................................................................. 38

DK Combi-Disc 4,5 –5,5 m 15-04-2020
4 Tilbage til indholdsfortegnelse
Middle frame for Disc-Roller....................................................................................................................... 39
Wheel frame before machinenumber 350873 ............................................................................................. 41
Wings............................................................................................................................................................. 43
Lock claw system .......................................................................................................................................... 45
Notes.................................................................................................................................................................. 47
Single V-Profile roller –scraper –material damper guard........................................................................ 48
Doubble U/V-Profil roller –scraper –material damper guard ................................................................. 49
Rubber damped bearings and protection shield for ordinary bearings...................................................... 51
U-Profile roller ............................................................................................................................................. 52
Disc bars........................................................................................................................................................ 53
Disc................................................................................................................................................................ 55
Edge Equipment ........................................................................................................................................... 57
Disc cutter in front of tines (additional equipment).................................................................................... 59
Lights............................................................................................................................................................. 61
Longfinger harrow (additional equipment)................................................................................................. 63
Electric dept stop for disc............................................................................................................................. 65
Hydraulic brake............................................................................................................................................ 67
Pneumatic brake........................................................................................................................................... 69
Hydraulic........................................................................................................................................................... 71
Tiller folding cylinders ................................................................................................................................. 71
Drawbar and transport wheels..................................................................................................................... 72
Hydraulics for stone protection.................................................................................................................... 73
Linkage ......................................................................................................................................................... 75
Folding 4,5m................................................................................................................................................. 76
Folding 5,5 m................................................................................................................................................ 77
Depth controller discs 4,5 meter................................................................................................................... 79
Depth controller discs 5,5 meter................................................................................................................... 80

DK Combi-Disc 4,5 –5,5 m 15-04-2020
5 Tilbage til indholdsfortegnelse
EC DECLARATION OF CONFORMITY
in accordance with the EU Machinery Directive 2006/42/EC
applicable as from December 29th 2009:
HE-VA ApS
N. A. Christensensvej 34,
DK-7900 Nykøbing Mors
hereby confirms that the following machine has been manufactured in accordance with the Council
Directive 2006/42/EC.
The declaration comprises the following machine:
Combi-Disc 4,5m –5,5m
Nykøbing the 1st of June 2017
Villy Christiansen
The undersigned is furthermore authorized to compile technical documentation for the above
machine.

UK Combi-Disc 4,5 –5,5m 20-06-2020
4Back to the table of contents
Delivery check
Setting-up of the machine
Check :
•the roller for any damage.
•the roller for any paint damage during transport.
•the hydraulic hoses for cuts and squeezing damage. Check also that the other hydraulic
components have not been damaged during transport.
•that the frame construction has not been damaged.
•that the transport wheel nuts are tightened and OK.
•the air pressure in the tyres (according to the technical specifications).
•that all wearing parts are intact.
•that all distance clips for depth control are delivered with the machine.
•and test the lights, (if mounted).
Check the tightening :
•of wheel bolts x-Nm according to specifications
•flange for towing eye 6 pcs of bolts 541 Nm

UK Combi-Disc 4,5 –5,5m 20-06-2020
5Back to the table of contents
Safety Instructions for Combi-Disc
Do not start-up the machine if there are persons in exposed positions** within a hazardous area*.
When persons are in exposed positions (e.g. in connection with adjustment, maintenance, attachment
and uncoupling), the following conditions must be observed:
•The machine must be lowered to firm ground.
•The hydraulics must be relieved.
•The tractor must be stopped and the key removed from the ignition switch.
•The driver must ensure that no persons are staying in exposed positions during the operation.
* Hazardous area: On and under the machine within a distance of 4 m from the
machine.
** Person in exposed position: Any person who is staying wholly or partly within a
hazardous area.
Most accidents that happen in connection with the operation, transport and maintenance of machines
are caused by non-compliance with the most elementary safety conditions.
Therefore it is vital that anybody working at the machine carefully complies with the safety
instructions as well as other instructions applying to the machine.
The machine may only be operated, maintained and repaired by persons, who are familiar with this
work and who are further familiar with the possible elements of danger with this particular machine.
ATTENTION !! Rotary parts and loose clothes are a dangerous combination.
IMPORTANT !! In connection with the risk of parts falling down, it may endanger the
lives of persons staying on the base frame of the machine, when it is
operated attached to a tractor.

UK Combi-Disc 4,5 –5,5m 20-06-2020
6Back to the table of contents
Safety and Instructions on Hydraulics
1. The maximum working pressure is 225 bar.
2. It is advisable to label the attachment parts at hydraulic connections between the tractor and the
tool in order to eliminate incorrect operation!
3. When checking for hydraulic leaks, use suitable safety wear (eye protectors, gloves, etc.)
High-pressure hydraulic oil may penetrate the skin and cause dangerous injuries.
In case of injury, consult a doctor immediately. RISK OF INFECTION!
4. After operating the hydraulics, lower the machine to firm ground.
Relieve the hydraulics, stop the motor and remove the ignition key.
5. Check the hydraulic hoses on a regular basis, however, every six months as a minimum due to
any cracks, wear and tear, etc. Replace any defective hoses immediately.
6. The life of hydraulic hoses is maximum 5 years.
New hydraulic hoses must meet the manufacturer's requirements.
Complaints
2-year guarantee:
2-year guarantee on all material and design defects, provided that HE-VA’s operating instructions are
followed and that only original HE-VA components have been used. Al warranty repair work is only
performed according to a prior agreement with HE-VA and within normal working hours. Machines
for improvement shall be submitted in cleaned condition.
The second year of the guarantee period only includes delivery of components and not replacement of
these.
No compensation for loss of operation and profit or other indirect losses.
With front-mounted tools, HE-VA disclaims any liability for the tractor.
INSTRUCTIONS ON TRANSPORT ON THE PUBLIC ROADS
Check before transport on public roads that the attachment of the machine at the tractor is in accordance
with the local rules and regulations in force (permitted total weight, permitted axle load, transport width,
lights, warning signs, etc.).
FRONT AXLE LOAD
After the attachment of the machine and at maximum load, the driving properties of the tractor must be
ensured. Check that the front axle is sufficiently loaded. As a minimum, the front axle load must be 20%
of the tractor weight. Permitted axle load and permitted total weight for the tractor must always be
observed.
NB! The driving, controlling and braking properties are affected by the attached machine
combination.

UK Combi-Disc 4,5 –5,5m 20-06-2020
7Back to the table of contents
Labels on the machine
You will find several labels on your Disc-Roller containing safety and practical instructions as regards
the correct application of the machine. Please study the instructions and point out to the user the
importance of the labels as well as the safety instructions in these Operating Instructions. Always keep
the labels clean and readable –if not they must be replaced.
Safety –and other markings on the machine
Study the Operating Instructions thoroughly before any
operation of the machine and observe all safety instructions.
Take care that no persons are within the machine’s hazardous
area during the unfolding and folding procedure..
Plate with number and year of manufacture
Tighten up the bolts regularly. If this is not performed, our
warranty obligations will no longer apply.
Maximum torque in Nm. w/lubricated thread
Metric thread
Quality 8.8
Quality 10.9
Quality 12.9
M10x1,5
47
65
79
M12x1,75
81
114
136
M14x2,0
128
181
217
M16x2,0
197
277
333
M18x2,5
275
386
463
M20x2,5
385
541
649
M22x2,5
518
728
874
M24x3,0
665
935
1120
Wheel-fixing bolt M18x1,5 fine-pitch thread
433 Nm
Wheel-fixing bolt M22x1,5 fine-pitch thread
803 Nm

UK Combi-Disc 4,5 –5,5m 20-06-2020
8Back to the table of contents
Technical Specifications / Data
Working
width
Roller type / Diameter
No. of
rings
No. of
tines
Weight kg
Quick-
push/hydr.
No. of
discs
Power
require-
ment, HK
4,25 m
Enkelt U-Profile 600 mm
30
7
5.375/5.525
34
300-400
Enkelt V-Profile 600 mm
30
7
5.540/5.690
34
300-400
Enkelt V-Profile 700 mm
30
7
5.810/5.960
34
300-400
Twin V-Profile 600-600 mm
30
7
5.520/5.670
34
300-400
Twin U-Profile 600-600 mm
30
7
5.850/6.000
34
300-400
5,25 m
Enkelt U-Profile 600 mm
36
9
6.315/6.465
42
350-450
Enkelt V-Profile 600 mm
36
9
6.490/6.640
42
350-450
Enkelt V-Profile 700 mm
36
9
6.820/6.970
42
350-450
Twin V-Profile 600-600 mm
36
9
6.460/6.610
42
350-450
Twin U-Profile 600-600 mm
36
9
6.810/6.960
42
350-450
Support wheels Tiller 4,25 / 5,25
Transport wheels Disc 4,25 / 5,25
300/55x14,5
Max. inflation Bar: 4,4
400/60x15,3-14 Ply / 500/50x17,0-18 Ply
Max. inflation Bar: 4,5 / 3,5
Transport height 4,25 / 5,25
Transport width 4,25 / 5,25
3,1 meter / 3,6 meter
2,62 meter / 2,62 meter
Combi-Tiller meets the standard DS/ISO 11001-1, three point linkage.
Transport
1. Lift the discs to the top before folding up the machine.
2. Then lift the machine to maximum transport height.
3. Now pressurise the folding cylinders and the side sections will be folded up. After
that put the function in floating position, however, ensure that the locking claws
have locked the side sections.
4. Now the machine is secured and ready for transport.
5. Lower the machine in order to minimise the transport height, to obtain a center of
gravity as low as possible. It is recommendable to drive slowly and carefully in
turns and roundabouts.

UK Combi-Disc 4,5 –5,5m 20-06-2020
9Back to the table of contents
Important:
Attachment
1. Reverse the tractor to the machine.
2. Connect all hydraulic hoses to the tractor outlets.
3. Pressurise the drawbar - and the wheel cylinder (red) so that the machine drawbar
is lifted to the suitable height.
4. Then reverse the tractor and attach the machine.
5. Now lift the machine to maximum height.
6. Fold up the side sections (blue) towards the stop on the centre frame.
7. When the side sections are unfolded, open the locking claws first and after that
the side sections will unfold.
8. When the side sections are completely unfolded, let go of the hydraulic handle
and the machine is ready for use.
Set the tractor’s flow control on MAX., to make sure that the side sections will
follow each other.
9. Unfold the edge equipment to working position.
10. Now lift and lower the discs to the required working depth. The support wheels at
the Tiller are not for depth controle of the tines, they are only meant to make sure
the machine operates with a steady movement to keep same working depth from
side to side.
Uncoupling
1. Lift the machine up and tilt the depth stop on the drawbar forward towards the
tractor.
2. Now lower the machine onto firm ground.
3. Adjust the drawbar –and wheel cylinder (red) so that the drawing bolt is loose.
4. Now the machine may be uncoupled.
5. Drive the tractor a little forward and then relieve all hydraulic hoses.
Important:
Put the machine on level ground
and relieve the hydraulics, before
leaving the machine.
Check that the towing hook height is between 500 and 550 mm.
Check that the male quick-couplings of the Disc-Roller fit the
female quick-couplings of the tractor.

UK Combi-Disc 4,5 –5,5m 20-06-2020
10 Back to the table of contents
Settings and adjustment
When starting-up the Combi-Disc, it is very important that the machine is parallel with the surface of
the earth. The packing roller and the tractor keep the machine in an exact working depth.
Support wheels are not for depth adjustment, but only to avoid uneven working depth at the tines from
side to side.
Drawbar
The horizontal position is adjusted by means of
the adjustment plates at the drawbar cylinder.
Height of the towing eye: approx. 500 - 550 mm
Disc
The Discs are adjusted up or down by a hydraulic
Master-Slave system.
It is important that the discs are regularly lifted to the top
to reset the Master-Slave system. The depth position is readable on the scale (standard).
The sensor can be adjusted, where el. depth stop is mounted.
It is possible to over steer the electrical system by turning off the switch mounted in the cabin, now the
discs can pass the sensor, thereby a deeper working depth is achieved e.g. at headland and tramlines.

UK Combi-Disc 4,5 –5,5m 20-06-2020
11 Back to the table of contents
He-va SAT system:
Hydraulic adjustable weight transfer system, ensuring equal weight transfer in the total working width,
resulting in the fact that the wing sections are following the ground.
Manometer for pressure adjustment on 2-sections machines
In transport position, the hydr. pressure in the system is adjusted to approx. 50 bar. During operation,
the hydr. pressure will vary - depending on the soil surface.

UK Combi-Disc 4,5 –5,5m 20-06-2020
12 Back to the table of contents
21
3
Edge equipment
The edge equipment can be adjusted
three places:
1. Loosen two bolts –move the
arm out/in.
2. Use the spindle –it raises
and lowers the disc. Loosen
two bolts –raise/lower by
the spindle and retighten the
bolts.
3. Loosen one bolt –tilt the
disc more or less.
Edge equipment for Disc-Roller
Contour
The disc can be adjusted so that
excavated soil is collected.
Keep the disc away from the ground
to avoid bending when turning.

UK Combi-Disc 4,5 –5,5m 20-06-2020
13 Back to the table of contents
Scraper
The Disc-Roller Contour has special designed scrapers among the packer rings on the single V-
Profile and U-Profile as well as on the Wave Roller.
To avoid unnecessary wear and to obtain the best scraper effect it is important to check the
centering of the scrapers every day.
Material-damper-guard
The Disc-Roller Contour can be equipped with material damper guard, ensuring that excavated soil
from the discs is falling down before packing.
The material damper guard is height adjustable in 5 cm steps,
by unlocking 1 pin in each bracket.
To dismount the material damper guard, unlock pins and unbolt.
5 cm
per step
trin

UK Combi-Disc 4,5 –5,5m 20-06-2020
14 Back to the table of contents
Stone protection
Quick-Push shearpin
When the shear bolt is broken and the tine has been released, place the shear bolt one notch forward
before the machine can operate again.
Pull out the hair-clip (Pos. 1).
Pull the tine back to normal working position (Pos. 2).
Push the shearpin (Pos. 3) one notch forward to a new position in the
tine. Do not push the bolt totally through
(it can be necessary to remove soil etc. from the hole in the tine).
Important: All activities under the machine are deprecated when the
shearpin is being moved or changed.
Push back the hair-clip (Pos. 1), so that it locks the shear bolt in its place,
and the machine is ready for operation.
When the shearpin is broken for the eighth time, it is used up.
Be aware that the shearpin must never be shorter than 65 mm.
When a new shear bolt is mounted it is important that it is placed rightly.
The end of 40 mm (Pos. 3) is to turn away from the tine.
OBS: A →Shims must always be mounted on the opposite side as the shearpin is inserted from.
1
2
3

UK Combi-Disc 4,5 –5,5m 20-06-2020
15 Back to the table of contents
Hydraulic automatic release system
Before each season it has to be controlled, that the gas pressure in the accumulator
(Pos.1) is 90 bars. This requires special tools and can only be performed by an
authorized dealer.
Before the start-up of the machine the hydraulic pressure in the closed hydraulic stone
protection system must be controlled on the machine’s pressure gauge (Pos. 2). The
hydraulic reset pressure should be minimum 120 bar and must not exceed 160 bar.
IMPORTANT –the hydraulic pressure is to be controlled continuously and must never be under
100 bar.
If there is a need to adjust the working pressure, follow the below instructions:
Mount the quick coupling of the hydraulic hose (Pos. 3) in the tractor’s oil outlet.
Turn on the ball valve (Pos. 4), and the working pressure can now be adjusted up or
down with the tractor’s oil outlet.
When the desired pressure is achieved, turn off the ball valve again (Pos. 4), and the
tractor’s hydraulic system is relieved before the quick coupling (Pos. 3) is dismounted
and placed in the parking device of the machine.
During the operation of the machine the tine is swinging automatically to the rear if it meets an
obstacle. In normal circumstances the tine will automatically return to the working position again
after having passed the obstacle. At extreme obstacles and/or soil conditions it might be necessary
to stop and eventually lift the machine from the soil.
It is important that no persons are near to the machine as the tine is returning to the
working position with high speed and might throw with soil and stones.
1
2
3
4

UK Combi-Disc 4,5 –5,5m 20-06-2020
16 Back to the table of contents
Replacement of wearing point
Before working with the machine’s wearing points, the machine is to be fastened.
This can be performed by trestles under the main frame.
Dismount M12x50 mm bolt (Pos. 1) by means of 2 pcs. 19 mm spanners. The
wearing point might fall off, when the bolt is removed –take care of foot and leg
injuries.
Dismount the wearing point by pushing it forward. This might be difficult due to
entrance of soil, and it might be a good idea to use a hammer.
Mount the new wearing point, item no. 645000044 (Pos. 2), by pushing the wearing
point to the rear and then in its place.
Check the M16 x 65 mm bolt for eventual damages and replace it as required, item no.
0235852+0272290+0264090
Mount the M16 x 65 mm bolt (Pos. 1), lubricate and tighten it with approx 20 Nm.
Be careful not to overtighten –the wearing point can be damaged
1
2

UK Combi-Disc 4,5 –5,5m 20-06-2020
17 Back to the table of contents
Maintenance and service
Important:
After 10 hours of operation, retighten wheels, bearings and stop rings. Check hydraulic hoses,
fittings and cylinders for leaks and retighten.
Check regularly that all bolts are tightened properly.
After end season, grease and wash machine, and grease the piston rods.
Lubrication
When greasing, maintaining and repair work, the machine must be lowered, the tractors brakes
activated and engine stopped
Tiller part:
There are 20 greasing nipples at the Combi-Tiller part, which has to be greased after every 15 hours
of operating and after washing the maschine. Greasing spots are located at the lift linkage, at all
hydraulic cylinders and at the wing sections bushings for hinges
There is 1 grease nipple at each support wheel in the hinges. The spindle in to adjust the support
wheel must be dismantled at least once a year to be greased (figure1).
There is 1 grease nipple at every hinge on the drawbar (figure 2).
On machines with hydraulic stone protection there are 2 grease nipples at each tine, which must be
greased every 10 hours operation (figure 3 og 4).
On the lift linkage her are 2 grease nipples at each arm (figure 3).
There are 2 grease nipples at each lift and folding cylinder (figure 5).
There are 3 grease nipples at each wing hinge (figure 6).
Disc-Roller part:
On the 4,5 meter Disc-Roller part there are 25 grease nipples and the 5,5 meter model there are 31
nipples.
There are 2 grease nipples at every hydraulic cylinder, except the 2 cylinders to adjust the depth of
the discs, which only have a nipple on the bushing (figure 7 and 8).
There is 1 grease nipple at each hinge on the wings, 4 pc. Total (figure 7).
There is 1 grease nipple at the transport wheel frame hinge (figure 9).
There is 1 grease nippæe at each roller bearing, which only have to be greased once or twice in
every season (figure 10).
Oil, type Hydro Texaco HD 32 has been
filled in the hydraulic system.

UK Combi-Disc 4,5 –5,5m 20-06-2020
18 Back to the table of contents
Figure 2
Figure 1
Figure 3
Figure 4
Figure 5

UK Combi-Disc 4,5 –5,5m 20-06-2020
19 Back to the table of contents
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10