Hearth & Home LOGS-NDI30 User manual

1
Hearth & Home Technologies • LOGS-NDI30 Log Instructions • 2226-935 Rev. C • 2/18
Log Set Assembly: LOGS-NDI30
Models: NDI30, NDI30-SP, NDI30-C, HNGINS-30-SP
LOG PLACEMENT INSTRUCTIONS
Log #1 (SRV2226-701) Position Log #1 as shown in Figure 2. Note additional placement instructions in Figure 1. Set the
rear log (Log #1) on the log shelf. Position the log against the back of the rebox. Center the log notch over the pilot assembly.
Figure 1.
LOG SHELF
Figure 2. Install Log #1
Figure 3. Place Log #2 Figure 4. Log #2
Log #2 (SRV2226-702): Position Log #2 as shown in Figure 3. Refer to Figure 1 and Figure 4 for additional details. Mate
the slot located on the bottom of Log #2 with the log pin located on the right side of the burner. Move the right end of Log
#2 forward until it comes into contact with the grate tine.
GRATE
TINES
LOG PINS
PILOT ASSEMBLY
GRATE BAR LOG
NOTCH
FLAT SPOT
FOR LOG #4
FLAT SPOT FOR
LOG #6
FLAT SPOT FOR
LOG #5
FLAT SPOT FOR
LOG #5
FLAT SPOT
FOR LOG #6
LOG
TOUCHES
GRATE TINE
MATE LOG
PIN WITH
LOG SLOT
SLOT
1
2
SRV2226-701
SRV2226-704
SRV2226-703
SRV2226-705
SRV2226-706
SRV2226-702
CAUTION: Logs are fragile, handle with care.

Hearth & Home Technologies • LOGS-NDI30 Log Instructions • 2226-935 Rev. C • 2/182
Log #4 (SRV2226-703): Position Log #4 as shown in Figure 7. See Figure 1 and Figure 2 for additional details. Place the
top end of log #4 on the at spot of Log #1. Position the forked end of Log #4 around the far left grate tine. Rotate the forked
end of the log to the left until the right fork touches the grate tine.
Log #5 (SRV2226-705): Position Log #5 as shown in Figure 8. Refer to Figures 1,2 and 3 for placement references. Position
the two forked ends of Log #5 on the at spots of Log #1 and Log #2. The thicker end of the logs rests on the grate bar.
Figure 7. Place Log #4 Figure 8. Place Log #5
Log #6 (SRV2226-704): Position Log #6 as shown in Figure 9. See Figures 1, 2 and 3 for additional details. Rest the forked
end of Log #6 on the at spot of Log #2. Position the back end of the log on the at spot of Log #1. Figure 10 shows the
log set properly installed.
LOG TOUCHES
GRATE TINE
PLACE TOP END OF
LOG ON FLAT SPOT
LOG TOUCHES
GRATE TINE
LOG RESTS ON
GRATE BAR
END OF LOGS
POSITIONED ON
FLAT SPOTS
Figure 9. Place Log #6 Figure 10. Log Set Installed
LOG POSITIONED
ON FLAT SPOT
FORKED END
RESTS ON
FLAT SPOT
45
6
Figure 5. Place Log #3 Figure 6. Log #3
Log #3 (SRV2226-706): Position Log #3 as shown in Figure 5. Refer to Figure 1 and Figure 6 for location of reference
points. Mate the slot located on the bottom of Log #3 with the log pin located on the left side of the burner. Move the left
end of Log #3 forward until it comes into contact with the grate tine.
LOG
TOUCHES
GRATE TINE
MATE LOG
PIN WITH
LOG SLOT SLOT
3